[Intel-gfx] [PATCH] [RFC] drm/i915/skl+: enable PF_ID interlace mode in SKL
Mahesh Kumar
mahesh1.kumar at intel.com
Wed Jun 7 09:49:05 UTC 2017
In previous GEN default Interlace mode enabled is IF-ID mode, but IF-ID
mode has many limitations in SKL. This mode doesn't support y-tiling,
90-270 rotation is not supported & YUV-420 planar source pixel formats
are not supported with above mode.
This patch make changes to use PF-ID Interlace mode in SKL+ platforms.
PF-ID mode require one scaler to be attached in pipe-scaling mode.
During WM calculation adjusted pixel rate need to be doubled.
During max_supported_pixel_format calculation vertical downscale is 2.0.
Signed-off-by: Mahesh Kumar <mahesh1.kumar at intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90238
---
drivers/gpu/drm/i915/intel_atomic.c | 13 ++++++++++
drivers/gpu/drm/i915/intel_display.c | 47 +++++++++++++++++++++++++++++++-----
drivers/gpu/drm/i915/intel_drv.h | 10 ++++++++
drivers/gpu/drm/i915/intel_panel.c | 9 +++++--
drivers/gpu/drm/i915/intel_pm.c | 17 ++++++++++++-
5 files changed, 87 insertions(+), 9 deletions(-)
diff --git a/drivers/gpu/drm/i915/intel_atomic.c b/drivers/gpu/drm/i915/intel_atomic.c
index d791b3ef89b5..06ed2fc449d7 100644
--- a/drivers/gpu/drm/i915/intel_atomic.c
+++ b/drivers/gpu/drm/i915/intel_atomic.c
@@ -248,6 +248,13 @@ int intel_atomic_setup_scalers(struct drm_i915_private *dev_priv,
return -EINVAL;
}
+ if (num_scalers_need > 1 &&
+ scaler_state->scaler_users & (1 << SKL_CRTC_INDEX) &&
+ scaler_state->scaler_users & (1 << SKL_PF_ID_INDEX)) {
+ DRM_ERROR("Can't attach scaler to CRTC in Interlace Mode\n");
+ return -EINVAL;
+ }
+
/* walkthrough scaler_users bits and start assigning scalers */
for (i = 0; i < sizeof(scaler_state->scaler_users) * 8; i++) {
int *scaler_id;
@@ -264,6 +271,12 @@ int intel_atomic_setup_scalers(struct drm_i915_private *dev_priv,
/* panel fitter case: assign as a crtc scaler */
scaler_id = &scaler_state->scaler_id;
+ } else if (i == SKL_PF_ID_INDEX) {
+ name = "PF-ID INTERLACE MODE";
+ idx = intel_crtc->base.base.id;
+
+ /* PF-ID interlaced mode case: needs a pipe scaler */
+ scaler_id = &scaler_state->scaler_id;
} else {
name = "PLANE";
diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c
index 85ac32549e85..15c79b46d645 100644
--- a/drivers/gpu/drm/i915/intel_display.c
+++ b/drivers/gpu/drm/i915/intel_display.c
@@ -4626,6 +4626,11 @@ skl_update_scaler(struct intel_crtc_state *crtc_state, bool force_detach,
*/
need_scaling = src_w != dst_w || src_h != dst_h;
+ if ((crtc_state->base.adjusted_mode.flags & DRM_MODE_FLAG_INTERLACE)
+ && scaler_user == SKL_PF_ID_INDEX)
+ /* PF-ID Interlace mode needs a scaler */
+ need_scaling = true;
+
/*
* if plane is being disabled or scaler is no more required or force detach
* - free scaler binded to this plane/crtc
@@ -4635,16 +4640,24 @@ skl_update_scaler(struct intel_crtc_state *crtc_state, bool force_detach,
* scaler can be assigned to other user. Actual register
* update to free the scaler is done in plane/panel-fit programming.
* For this purpose crtc/plane_state->scaler_id isn't reset here.
+ * Now Interlace mode is a new user of pipe-scaler, so free the scaler-id
+ * only if call is for respective user. If no user for scaler free it.
*/
if (force_detach || !need_scaling) {
- if (*scaler_id >= 0) {
+ if (*scaler_id >= 0 &&
+ scaler_state->scaler_users & (1 << scaler_user)) {
scaler_state->scaler_users &= ~(1 << scaler_user);
scaler_state->scalers[*scaler_id].in_use = 0;
DRM_DEBUG_KMS("scaler_user index %u.%u: "
"Staged freeing scaler id %d scaler_users = 0x%x\n",
- intel_crtc->pipe, scaler_user, *scaler_id,
- scaler_state->scaler_users);
+ intel_crtc->pipe, scaler_user,
+ *scaler_id, scaler_state->scaler_users);
+
+ *scaler_id = -1;
+ }
+ if (*scaler_id >= 0 && !scaler_state->scaler_users) {
+ scaler_state->scalers[*scaler_id].in_use = 0;
*scaler_id = -1;
}
return 0;
@@ -4691,6 +4704,16 @@ int skl_update_scaler_crtc(struct intel_crtc_state *state)
adjusted_mode->crtc_hdisplay, adjusted_mode->crtc_vdisplay);
}
+static int skl_update_scaler_crtc_pf_id_output(struct intel_crtc_state *state)
+{
+ const struct drm_display_mode *mode = &state->base.adjusted_mode;
+
+ return skl_update_scaler(state, !state->base.active,
+ SKL_PF_ID_INDEX, &state->scaler_state.scaler_id,
+ state->pipe_src_w, state->pipe_src_h,
+ mode->crtc_hdisplay, mode->crtc_vdisplay);
+}
+
/**
* skl_update_scaler_plane - Stages update to scaler state for a given plane.
*
@@ -6258,6 +6281,15 @@ static int intel_crtc_compute_config(struct intel_crtc *crtc,
}
}
+ if (INTEL_GEN(dev_priv) >= 9) {
+ if (skl_update_scaler_crtc_pf_id_output(pipe_config)) {
+ DRM_ERROR("Unable to set scaler for PF-ID mode\n");
+ return -EINVAL;
+ }
+ intel_pch_panel_fitting(crtc, pipe_config,
+ DRM_MODE_SCALE_FULLSCREEN);
+ }
+
if (adjusted_mode->crtc_clock > clock_limit) {
DRM_DEBUG_KMS("requested pixel clock (%d kHz) too high (max: %d kHz, double wide: %s)\n",
adjusted_mode->crtc_clock, clock_limit,
@@ -8045,9 +8077,12 @@ static void haswell_set_pipeconf(struct drm_crtc *crtc)
if (IS_HASWELL(dev_priv) && intel_crtc->config->dither)
val |= (PIPECONF_DITHER_EN | PIPECONF_DITHER_TYPE_SP);
- if (intel_crtc->config->base.adjusted_mode.flags & DRM_MODE_FLAG_INTERLACE)
- val |= PIPECONF_INTERLACED_ILK;
- else
+ if (intel_crtc->config->base.adjusted_mode.flags & DRM_MODE_FLAG_INTERLACE) {
+ if (INTEL_GEN(dev_priv) >= 9)
+ val |= PIPECONF_PFIT_PF_INTERLACED_ILK;
+ else
+ val |= PIPECONF_INTERLACED_ILK;
+ } else
val |= PIPECONF_PROGRESSIVE;
I915_WRITE(PIPECONF(cpu_transcoder), val);
diff --git a/drivers/gpu/drm/i915/intel_drv.h b/drivers/gpu/drm/i915/intel_drv.h
index 83dd40905821..d4546f6498b9 100644
--- a/drivers/gpu/drm/i915/intel_drv.h
+++ b/drivers/gpu/drm/i915/intel_drv.h
@@ -483,6 +483,7 @@ struct intel_crtc_scaler_state {
* avilability.
*/
#define SKL_CRTC_INDEX 31
+#define SKL_PF_ID_INDEX 29
unsigned scaler_users;
/* scaler used by crtc for panel fitting purpose */
@@ -1206,6 +1207,15 @@ hdmi_to_dig_port(struct intel_hdmi *intel_hdmi)
return container_of(intel_hdmi, struct intel_digital_port, hdmi);
}
+static inline bool
+is_skl_interlace_mode(struct drm_i915_private *dev_priv,
+ const struct drm_display_mode *mode)
+{
+ if (INTEL_GEN(dev_priv) < 9)
+ return false;
+ return mode->flags & DRM_MODE_FLAG_INTERLACE;
+}
+
/* intel_fifo_underrun.c */
bool intel_set_cpu_fifo_underrun_reporting(struct drm_i915_private *dev_priv,
enum pipe pipe, bool enable);
diff --git a/drivers/gpu/drm/i915/intel_panel.c b/drivers/gpu/drm/i915/intel_panel.c
index 4114cb3f14e7..fae7fe7802f8 100644
--- a/drivers/gpu/drm/i915/intel_panel.c
+++ b/drivers/gpu/drm/i915/intel_panel.c
@@ -108,9 +108,14 @@ intel_pch_panel_fitting(struct intel_crtc *intel_crtc,
const struct drm_display_mode *adjusted_mode = &pipe_config->base.adjusted_mode;
int x = 0, y = 0, width = 0, height = 0;
- /* Native modes don't need fitting */
+ /*
+ * Native modes don't need fitting
+ * PF-ID Interlace mode in SKL+ require a pipe scaler
+ */
if (adjusted_mode->crtc_hdisplay == pipe_config->pipe_src_w &&
- adjusted_mode->crtc_vdisplay == pipe_config->pipe_src_h)
+ adjusted_mode->crtc_vdisplay == pipe_config->pipe_src_h &&
+ !(is_skl_interlace_mode(to_i915(intel_crtc->base.dev),
+ adjusted_mode)))
goto done;
switch (fitting_mode) {
diff --git a/drivers/gpu/drm/i915/intel_pm.c b/drivers/gpu/drm/i915/intel_pm.c
index aa9d8cef7ce0..dfb21f00fbed 100644
--- a/drivers/gpu/drm/i915/intel_pm.c
+++ b/drivers/gpu/drm/i915/intel_pm.c
@@ -3873,15 +3873,18 @@ static uint_fixed_16_16_t
skl_pipe_downscale_amount(const struct intel_crtc_state *crtc_state)
{
uint_fixed_16_16_t pipe_downscale = u32_to_fixed_16_16(1);
+ const struct drm_display_mode *mode;
if (!crtc_state->base.enable)
return pipe_downscale;
+ mode = &crtc_state->base.adjusted_mode;
if (crtc_state->pch_pfit.enabled) {
uint32_t src_w, src_h, dst_w, dst_h;
uint32_t pfit_size = crtc_state->pch_pfit.size;
uint_fixed_16_16_t fp_w_ratio, fp_h_ratio;
uint_fixed_16_16_t downscale_h, downscale_w;
+ uint_fixed_16_16_t min_h_downscale;
src_w = crtc_state->pipe_src_w;
src_h = crtc_state->pipe_src_h;
@@ -3891,10 +3894,19 @@ skl_pipe_downscale_amount(const struct intel_crtc_state *crtc_state)
if (!dst_w || !dst_h)
return pipe_downscale;
+ /*
+ * Interlace mode require 1 scaler so no other scaler can be
+ * attached to pipe. PF-ID mode is equivalent to 2.0 vertical
+ * downscale.
+ */
+ if (mode->flags & DRM_MODE_FLAG_INTERLACE)
+ min_h_downscale = u32_to_fixed_16_16(2);
+ else
+ min_h_downscale = u32_to_fixed_16_16(1);
fp_w_ratio = fixed_16_16_div(src_w, dst_w);
fp_h_ratio = fixed_16_16_div(src_h, dst_h);
downscale_w = max_fixed_16_16(fp_w_ratio, u32_to_fixed_16_16(1));
- downscale_h = max_fixed_16_16(fp_h_ratio, u32_to_fixed_16_16(1));
+ downscale_h = max_fixed_16_16(fp_h_ratio, min_h_downscale);
pipe_downscale = mul_fixed16(downscale_w, downscale_h);
}
@@ -4418,6 +4430,9 @@ skl_adjusted_plane_pixel_rate(const struct intel_crtc_state *cstate,
* with additional adjustments for plane-specific scaling.
*/
adjusted_pixel_rate = cstate->pixel_rate;
+ if (cstate->base.adjusted_mode.flags & DRM_MODE_FLAG_INTERLACE)
+ adjusted_pixel_rate *= 2;
+
downscale_amount = skl_plane_downscale_amount(cstate, pstate);
return mul_round_up_u32_fixed16(adjusted_pixel_rate,
--
2.11.0
More information about the Intel-gfx
mailing list