[Intel-gfx] [PATCH] Revert "drm/i915/skl: New ddb allocation algorithm"
Rodrigo Vivi
rodrigo.vivi at gmail.com
Thu Jun 15 21:01:00 UTC 2017
On Thu, Jun 15, 2017 at 1:55 PM, Matt Roper <matthew.d.roper at intel.com> wrote:
> On Thu, Jun 15, 2017 at 01:52:02PM -0700, Rodrigo Vivi wrote:
>> On Thu, Jun 15, 2017 at 1:13 PM, Jani Nikula
>> <jani.nikula at linux.intel.com> wrote:
>> > On Thu, 15 Jun 2017, Ander Conselvan De Oliveira <conselvan2 at gmail.com> wrote:
>> >> On Thu, 2017-06-15 at 09:44 +0530, Mahesh Kumar wrote:
>> >>> Hi Ander,
>> >>>
>> >>>
>> >>> On Wednesday 14 June 2017 05:17 PM, Ander Conselvan De Oliveira wrote:
>> >>> > On Tue, 2017-06-13 at 12:06 -0700, Rodrigo Vivi wrote:
>> >>> > > On Tue, Jun 13, 2017 at 11:07 AM, Matt Roper <matthew.d.roper at intel.com> wrote:
>> >>> > > > On Tue, Jun 13, 2017 at 10:52:30AM -0700, Rodrigo Vivi wrote:
>> >>> > > > > This reverts commit bb9d85f6e9de8fef5236c076530eab67a2f2431b.
>> >>> > > > >
>> >>> > > > > New ddb allocation algorithm is a show stopper on my SKL system.
>> >>> > > > >
>> >>> > > > > Besides not be able to get external DP 4k at 60 (through USB type C),
>> >>> > > > > It fully hang my screen when unplugging the USB type C.
>> >>> > > > >
>> >>> > > > > Cc: Mahesh Kumar <mahesh1.kumar at intel.com>
>> >>> > > > > Cc: Maarten Lankhorst <maarten.lankhorst at linux.intel.com>
>> >>> > > > > Cc: Matt Roper <matthew.d.roper at intel.com>
>> >>> > > > > Signed-off-by: Rodrigo Vivi <rodrigo.vivi at intel.com>
>> >>> > > >
>> >>> > > > Is there a bugzilla entry with details/logs from the failure we can
>> >>> > > > refer to?
>> >>> > >
>> >>> > > nope, since I know it was working few weeks ago and then stopped
>> >>> > > working I went directly
>> >>> > > to bisect so I could get my system usable quickly again.
>> >>> > >
>> >>> > > But yes, I need to open a proper bugzilla and provide logs.
>> >>> > > Should we revert first and grab logs latter or we are going to try to
>> >>> > > analyse logs and fix?
>> >>> > >
>> >>> > > Anyways this is a big show stopper so I believe we revert at least
>> >>> > > before next pull request.
>> >>> >
>> >>> > This patch also causes artifacts in dual screen setups. All the scanlines below
>> >>> > the mouse cursor are wrong, sometimes containing a shade of gray and others
>> >>> > repeating the image above. I've seen this in APL and GLK using DSI+HDMI,
>> >>> > eDP+HDMI and DSI+DP. In the DP case, however, the screen goes blank and reports
>> >>> > lack of signal.
>> >>> >
>> >>> > I've noticed fifo underrun messages. I compared the ddb allocation in GLK with a
>> >>> > working and non-working kernel, but they were the same.
>> >>>
>> >>> your observation looks like one we observed in one of the Linux variant
>> >>> program.
>> >>> There was an configuration where lower WM-level having higher DDB
>> >>> requirement than higher levels. Which was leading to lower WM levels
>> >>> getting disabled.
>> >>>
>> >>> Can you please try with following patch to see if it's solving the problem.
>> >>>
>> >>> https://patchwork.freedesktop.org/patch/161571/
>> >>
>> >> I tested that in my GLK, but it didn't help. Still getting artifacts following
>> >> the mouse cursor.
>> >
>> > If the revert helps the GLK case as well, please let's revert. We
>> > generally waste too much time trying to get things fixed when the revert
>> > and return to the drawing board is the way to go.
>>
>> Agreed.
>> But:
>>
>> dim: ERROR: 11cabd424587c77596ceb198284a4c50a2784602 is lacking
>> mandatory review, aborting
>
> Does dim require a formal r-b on direct reverts? If so, you can promote
> my Acked-by to a full Reviewed-by to make it happy. :-)
Maybe it is something we need to fix in dim, but while I'm not sure I
will fully respect dim and use your rv-b,
and also respect Jani request and keep Fixes.
Thanks
>
>
> Matt
>
>>
>> >
>> > Rodrigo, please add the Bugzilla: reference and proper Fixes: line.
>>
>> Do we need "Fixes:" on the Revert who already references the original
>> git commit?
>> I didn't find any Revert patch in our tree with the Fixes this is why
>> I'm asking.
>>
>> >
>> > BR,
>> > Jani.
>> >
>> >
>> >>
>> >> Ander
>> >>
>> >>> Rodrigo,
>> >>>
>> >>> Can you please also check if this is the same reason for your failure.
>> >>> I'm arranging for a system with SKL+USB type-C DP 4K at 60 & eDP. will
>> >>> debug this further.
>> >>>
>> >>> -Mahesh
>> >>>
>> >>> >
>> >>> > Ander
>> >>> > > When you say you can't get DP 4k at 60, are you seeing messages
>> >>> > > > in dmesg about the setup being outside system watermark limitations or
>> >>> > > > are you just getting a black screen?
>> >>> > >
>> >>> > > just getting a blank screen on DP when plugging usb-c and a locked-up
>> >>> > > screen on eDP when removing usb-c.
>> >>> > >
>> >>> > > >
>> >>> > > > Matt
>> >>> > > >
>> >>> > > > > ---
>> >>> > > > > drivers/gpu/drm/i915/intel_pm.c | 257 +++++++++++++++-------------------------
>> >>> > > > > 1 file changed, 98 insertions(+), 159 deletions(-)
>> >>> > > > >
>> >>> > > > > diff --git a/drivers/gpu/drm/i915/intel_pm.c b/drivers/gpu/drm/i915/intel_pm.c
>> >>> > > > > index aa9d8ce..dc4275d 100644
>> >>> > > > > --- a/drivers/gpu/drm/i915/intel_pm.c
>> >>> > > > > +++ b/drivers/gpu/drm/i915/intel_pm.c
>> >>> > > > > @@ -4140,41 +4140,13 @@ int skl_check_pipe_max_pixel_rate(struct intel_crtc *intel_crtc,
>> >>> > > > > minimum[PLANE_CURSOR] = skl_cursor_allocation(num_active);
>> >>> > > > > }
>> >>> > > > >
>> >>> > > > > -static void
>> >>> > > > > -skl_enable_plane_wm_levels(const struct drm_i915_private *dev_priv,
>> >>> > > > > - uint16_t plane_ddb,
>> >>> > > > > - uint16_t max_level,
>> >>> > > > > - struct skl_plane_wm *wm)
>> >>> > > > > -{
>> >>> > > > > - int level;
>> >>> > > > > - /*
>> >>> > > > > - * Now enable all levels in WM structure which can be enabled
>> >>> > > > > - * using current DDB allocation
>> >>> > > > > - */
>> >>> > > > > - for (level = ilk_wm_max_level(dev_priv); level >= 0; level--) {
>> >>> > > > > - struct skl_wm_level *level_wm = &wm->wm[level];
>> >>> > > > > -
>> >>> > > > > - if (level > max_level || level_wm->plane_res_b == 0
>> >>> > > > > - || level_wm->plane_res_l >= 31
>> >>> > > > > - || level_wm->plane_res_b >= plane_ddb) {
>> >>> > > > > - level_wm->plane_en = false;
>> >>> > > > > - level_wm->plane_res_b = 0;
>> >>> > > > > - level_wm->plane_res_l = 0;
>> >>> > > > > - } else {
>> >>> > > > > - level_wm->plane_en = true;
>> >>> > > > > - }
>> >>> > > > > - }
>> >>> > > > > -}
>> >>> > > > > -
>> >>> > > > > static int
>> >>> > > > > skl_allocate_pipe_ddb(struct intel_crtc_state *cstate,
>> >>> > > > > - struct skl_pipe_wm *pipe_wm,
>> >>> > > > > struct skl_ddb_allocation *ddb /* out */)
>> >>> > > > > {
>> >>> > > > > struct drm_atomic_state *state = cstate->base.state;
>> >>> > > > > struct drm_crtc *crtc = cstate->base.crtc;
>> >>> > > > > struct drm_device *dev = crtc->dev;
>> >>> > > > > - struct drm_i915_private *dev_priv = to_i915(dev);
>> >>> > > > > struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
>> >>> > > > > enum pipe pipe = intel_crtc->pipe;
>> >>> > > > > struct skl_ddb_entry *alloc = &cstate->wm.skl.ddb;
>> >>> > > > > @@ -4187,9 +4159,6 @@ int skl_check_pipe_max_pixel_rate(struct intel_crtc *intel_crtc,
>> >>> > > > > unsigned plane_data_rate[I915_MAX_PLANES] = {};
>> >>> > > > > unsigned plane_y_data_rate[I915_MAX_PLANES] = {};
>> >>> > > > > uint16_t total_min_blocks = 0;
>> >>> > > > > - uint16_t total_level_ddb;
>> >>> > > > > - uint16_t plane_blocks = 0;
>> >>> > > > > - int max_level, level;
>> >>> > > > >
>> >>> > > > > /* Clear the partitioning for disabled planes. */
>> >>> > > > > memset(ddb->plane[pipe], 0, sizeof(ddb->plane[pipe]));
>> >>> > > > > @@ -4228,48 +4197,10 @@ int skl_check_pipe_max_pixel_rate(struct intel_crtc *intel_crtc,
>> >>> > > > > return -EINVAL;
>> >>> > > > > }
>> >>> > > > >
>> >>> > > > > - alloc_size -= minimum[PLANE_CURSOR];
>> >>> > > > > - ddb->plane[pipe][PLANE_CURSOR].start = alloc->end -
>> >>> > > > > - minimum[PLANE_CURSOR];
>> >>> > > > > + alloc_size -= total_min_blocks;
>> >>> > > > > + ddb->plane[pipe][PLANE_CURSOR].start = alloc->end - minimum[PLANE_CURSOR];
>> >>> > > > > ddb->plane[pipe][PLANE_CURSOR].end = alloc->end;
>> >>> > > > >
>> >>> > > > > - for (level = ilk_wm_max_level(dev_priv); level >= 0; level--) {
>> >>> > > > > - total_level_ddb = 0;
>> >>> > > > > - for_each_plane_id_on_crtc(intel_crtc, plane_id) {
>> >>> > > > > - /*
>> >>> > > > > - * TODO: We should calculate watermark values for Y/UV
>> >>> > > > > - * plane both in case of NV12 format and use both values
>> >>> > > > > - * for ddb calculation. NV12 is disabled as of now, So
>> >>> > > > > - * using only single/UV plane value here.
>> >>> > > > > - */
>> >>> > > > > - struct skl_plane_wm *wm = &pipe_wm->planes[plane_id];
>> >>> > > > > - uint16_t plane_res_b = wm->wm[level].plane_res_b;
>> >>> > > > > - uint16_t min = minimum[plane_id] + y_minimum[plane_id];
>> >>> > > > > -
>> >>> > > > > - if (plane_id == PLANE_CURSOR)
>> >>> > > > > - continue;
>> >>> > > > > -
>> >>> > > > > - total_level_ddb += max(plane_res_b, min);
>> >>> > > > > - }
>> >>> > > > > -
>> >>> > > > > - /*
>> >>> > > > > - * If This level can successfully be enabled with the
>> >>> > > > > - * pipe's current DDB allocation, then all lower levels are
>> >>> > > > > - * guaranteed to succeed as well.
>> >>> > > > > - */
>> >>> > > > > - if (total_level_ddb <= alloc_size)
>> >>> > > > > - break;
>> >>> > > > > - }
>> >>> > > > > -
>> >>> > > > > - if ((level < 0) || (total_min_blocks > alloc_size)) {
>> >>> > > > > - DRM_DEBUG_KMS("Requested display configuration exceeds system DDB limitations");
>> >>> > > > > - DRM_DEBUG_KMS("minimum required %d/%d\n", (level < 0) ?
>> >>> > > > > - total_level_ddb : total_min_blocks, alloc_size);
>> >>> > > > > - return -EINVAL;
>> >>> > > > > - }
>> >>> > > > > - max_level = level;
>> >>> > > > > - alloc_size -= total_level_ddb;
>> >>> > > > > -
>> >>> > > > > /*
>> >>> > > > > * 2. Distribute the remaining space in proportion to the amount of
>> >>> > > > > * data each plane needs to fetch from memory.
>> >>> > > > > @@ -4279,24 +4210,13 @@ int skl_check_pipe_max_pixel_rate(struct intel_crtc *intel_crtc,
>> >>> > > > > total_data_rate = skl_get_total_relative_data_rate(cstate,
>> >>> > > > > plane_data_rate,
>> >>> > > > > plane_y_data_rate);
>> >>> > > > > - /*
>> >>> > > > > - * PLANE_CURSOR data rate is not included in total_data_rate.
>> >>> > > > > - * If only cursor plane is enabled we have to enable its WM levels
>> >>> > > > > - * explicitly before returning. Cursor has fixed ddb allocation,
>> >>> > > > > - * So it's ok to always check cursor WM enabling before return.
>> >>> > > > > - */
>> >>> > > > > - plane_blocks = skl_ddb_entry_size(&ddb->plane[pipe][PLANE_CURSOR]);
>> >>> > > > > - skl_enable_plane_wm_levels(dev_priv, plane_blocks, max_level,
>> >>> > > > > - &pipe_wm->planes[PLANE_CURSOR]);
>> >>> > > > > if (total_data_rate == 0)
>> >>> > > > > return 0;
>> >>> > > > >
>> >>> > > > > start = alloc->start;
>> >>> > > > > for_each_plane_id_on_crtc(intel_crtc, plane_id) {
>> >>> > > > > unsigned int data_rate, y_data_rate;
>> >>> > > > > - uint16_t plane_blocks = 0, y_plane_blocks = 0;
>> >>> > > > > - struct skl_plane_wm *wm = &pipe_wm->planes[plane_id];
>> >>> > > > > - uint16_t plane_res_b = wm->wm[max_level].plane_res_b;
>> >>> > > > > + uint16_t plane_blocks, y_plane_blocks = 0;
>> >>> > > > >
>> >>> > > > > if (plane_id == PLANE_CURSOR)
>> >>> > > > > continue;
>> >>> > > > > @@ -4308,36 +4228,33 @@ int skl_check_pipe_max_pixel_rate(struct intel_crtc *intel_crtc,
>> >>> > > > > * promote the expression to 64 bits to avoid overflowing, the
>> >>> > > > > * result is < available as data_rate / total_data_rate < 1
>> >>> > > > > */
>> >>> > > > > + plane_blocks = minimum[plane_id];
>> >>> > > > > + plane_blocks += div_u64((uint64_t)alloc_size * data_rate,
>> >>> > > > > + total_data_rate);
>> >>> > > > >
>> >>> > > > > /* Leave disabled planes at (0,0) */
>> >>> > > > > if (data_rate) {
>> >>> > > > > - plane_blocks = max(minimum[plane_id], plane_res_b);
>> >>> > > > > - plane_blocks += div_u64((uint64_t)alloc_size *
>> >>> > > > > - data_rate, total_data_rate);
>> >>> > > > > ddb->plane[pipe][plane_id].start = start;
>> >>> > > > > ddb->plane[pipe][plane_id].end = start + plane_blocks;
>> >>> > > > > - start += plane_blocks;
>> >>> > > > > }
>> >>> > > > >
>> >>> > > > > + start += plane_blocks;
>> >>> > > > > +
>> >>> > > > > /*
>> >>> > > > > * allocation for y_plane part of planar format:
>> >>> > > > > - * TODO: Once we start calculating watermark values for Y/UV
>> >>> > > > > - * plane both consider it for initial allowed wm blocks.
>> >>> > > > > */
>> >>> > > > > y_data_rate = plane_y_data_rate[plane_id];
>> >>> > > > >
>> >>> > > > > + y_plane_blocks = y_minimum[plane_id];
>> >>> > > > > + y_plane_blocks += div_u64((uint64_t)alloc_size * y_data_rate,
>> >>> > > > > + total_data_rate);
>> >>> > > > > +
>> >>> > > > > if (y_data_rate) {
>> >>> > > > > - y_plane_blocks = y_minimum[plane_id];
>> >>> > > > > - y_plane_blocks += div_u64((uint64_t)alloc_size *
>> >>> > > > > - y_data_rate, total_data_rate);
>> >>> > > > > ddb->y_plane[pipe][plane_id].start = start;
>> >>> > > > > ddb->y_plane[pipe][plane_id].end = start + y_plane_blocks;
>> >>> > > > > - start += y_plane_blocks;
>> >>> > > > > }
>> >>> > > > > - skl_enable_plane_wm_levels(dev_priv,
>> >>> > > > > - plane_blocks,
>> >>> > > > > - max_level,
>> >>> > > > > - wm);
>> >>> > > > > +
>> >>> > > > > + start += y_plane_blocks;
>> >>> > > > > }
>> >>> > > > >
>> >>> > > > > return 0;
>> >>> > > > > @@ -4427,9 +4344,11 @@ static uint_fixed_16_16_t skl_wm_method2(uint32_t pixel_rate,
>> >>> > > > > static int skl_compute_plane_wm(const struct drm_i915_private *dev_priv,
>> >>> > > > > struct intel_crtc_state *cstate,
>> >>> > > > > const struct intel_plane_state *intel_pstate,
>> >>> > > > > + uint16_t ddb_allocation,
>> >>> > > > > int level,
>> >>> > > > > uint16_t *out_blocks, /* out */
>> >>> > > > > - uint8_t *out_lines /* out */)
>> >>> > > > > + uint8_t *out_lines, /* out */
>> >>> > > > > + bool *enabled /* out */)
>> >>> > > > > {
>> >>> > > > > struct intel_plane *plane = to_intel_plane(intel_pstate->base.plane);
>> >>> > > > > const struct drm_plane_state *pstate = &intel_pstate->base;
>> >>> > > > > @@ -4452,8 +4371,10 @@ static int skl_compute_plane_wm(const struct drm_i915_private *dev_priv,
>> >>> > > > > bool y_tiled, x_tiled;
>> >>> > > > >
>> >>> > > > > if (latency == 0 ||
>> >>> > > > > - !intel_wm_plane_visible(cstate, intel_pstate))
>> >>> > > > > + !intel_wm_plane_visible(cstate, intel_pstate)) {
>> >>> > > > > + *enabled = false;
>> >>> > > > > return 0;
>> >>> > > > > + }
>> >>> > > > >
>> >>> > > > > y_tiled = fb->modifier == I915_FORMAT_MOD_Y_TILED ||
>> >>> > > > > fb->modifier == I915_FORMAT_MOD_Yf_TILED;
>> >>> > > > > @@ -4541,6 +4462,9 @@ static int skl_compute_plane_wm(const struct drm_i915_private *dev_priv,
>> >>> > > > > if ((cpp * cstate->base.adjusted_mode.crtc_htotal / 512 < 1) &&
>> >>> > > > > (plane_bytes_per_line / 512 < 1))
>> >>> > > > > selected_result = method2;
>> >>> > > > > + else if ((ddb_allocation && ddb_allocation /
>> >>> > > > > + fixed_16_16_to_u32_round_up(plane_blocks_per_line)) >= 1)
>> >>> > > > > + selected_result = min_fixed_16_16(method1, method2);
>> >>> > > > > else if (latency >= linetime_us)
>> >>> > > > > selected_result = min_fixed_16_16(method1, method2);
>> >>> > > > > else
>> >>> > > > > @@ -4560,42 +4484,64 @@ static int skl_compute_plane_wm(const struct drm_i915_private *dev_priv,
>> >>> > > > > }
>> >>> > > > > }
>> >>> > > > >
>> >>> > > > > - if (res_lines >= 31 && level == 0) {
>> >>> > > > > - struct drm_plane *plane = pstate->plane;
>> >>> > > > > + if (res_blocks >= ddb_allocation || res_lines > 31) {
>> >>> > > > > + *enabled = false;
>> >>> > > > >
>> >>> > > > > - DRM_DEBUG_KMS("Requested display configuration exceeds system watermark limitations\n");
>> >>> > > > > - DRM_DEBUG_KMS("[PLANE:%d:%s] lines required = %u/31\n",
>> >>> > > > > - plane->base.id, plane->name, res_lines);
>> >>> > > > > - return -EINVAL;
>> >>> > > > > + /*
>> >>> > > > > + * If there are no valid level 0 watermarks, then we can't
>> >>> > > > > + * support this display configuration.
>> >>> > > > > + */
>> >>> > > > > + if (level) {
>> >>> > > > > + return 0;
>> >>> > > > > + } else {
>> >>> > > > > + struct drm_plane *plane = pstate->plane;
>> >>> > > > > +
>> >>> > > > > + DRM_DEBUG_KMS("Requested display configuration exceeds system watermark limitations\n");
>> >>> > > > > + DRM_DEBUG_KMS("[PLANE:%d:%s] blocks required = %u/%u, lines required = %u/31\n",
>> >>> > > > > + plane->base.id, plane->name,
>> >>> > > > > + res_blocks, ddb_allocation, res_lines);
>> >>> > > > > + return -EINVAL;
>> >>> > > > > + }
>> >>> > > > > }
>> >>> > > > >
>> >>> > > > > *out_blocks = res_blocks;
>> >>> > > > > *out_lines = res_lines;
>> >>> > > > > + *enabled = true;
>> >>> > > > >
>> >>> > > > > return 0;
>> >>> > > > > }
>> >>> > > > >
>> >>> > > > > static int
>> >>> > > > > skl_compute_wm_levels(const struct drm_i915_private *dev_priv,
>> >>> > > > > + struct skl_ddb_allocation *ddb,
>> >>> > > > > struct intel_crtc_state *cstate,
>> >>> > > > > const struct intel_plane_state *intel_pstate,
>> >>> > > > > struct skl_plane_wm *wm)
>> >>> > > > > {
>> >>> > > > > + struct intel_crtc *intel_crtc = to_intel_crtc(cstate->base.crtc);
>> >>> > > > > + struct drm_plane *plane = intel_pstate->base.plane;
>> >>> > > > > + struct intel_plane *intel_plane = to_intel_plane(plane);
>> >>> > > > > + uint16_t ddb_blocks;
>> >>> > > > > + enum pipe pipe = intel_crtc->pipe;
>> >>> > > > > int level, max_level = ilk_wm_max_level(dev_priv);
>> >>> > > > > int ret;
>> >>> > > > >
>> >>> > > > > if (WARN_ON(!intel_pstate->base.fb))
>> >>> > > > > return -EINVAL;
>> >>> > > > >
>> >>> > > > > + ddb_blocks = skl_ddb_entry_size(&ddb->plane[pipe][intel_plane->id]);
>> >>> > > > > +
>> >>> > > > > for (level = 0; level <= max_level; level++) {
>> >>> > > > > struct skl_wm_level *result = &wm->wm[level];
>> >>> > > > >
>> >>> > > > > ret = skl_compute_plane_wm(dev_priv,
>> >>> > > > > cstate,
>> >>> > > > > intel_pstate,
>> >>> > > > > + ddb_blocks,
>> >>> > > > > level,
>> >>> > > > > &result->plane_res_b,
>> >>> > > > > - &result->plane_res_l);
>> >>> > > > > + &result->plane_res_l,
>> >>> > > > > + &result->plane_en);
>> >>> > > > > if (ret)
>> >>> > > > > return ret;
>> >>> > > > > }
>> >>> > > > > @@ -4661,7 +4607,8 @@ static int skl_build_pipe_wm(struct intel_crtc_state *cstate,
>> >>> > > > >
>> >>> > > > > wm = &pipe_wm->planes[plane_id];
>> >>> > > > >
>> >>> > > > > - ret = skl_compute_wm_levels(dev_priv, cstate, intel_pstate, wm);
>> >>> > > > > + ret = skl_compute_wm_levels(dev_priv, ddb, cstate,
>> >>> > > > > + intel_pstate, wm);
>> >>> > > > > if (ret)
>> >>> > > > > return ret;
>> >>> > > > > skl_compute_transition_wm(cstate, &wm->trans_wm);
>> >>> > > > > @@ -4774,45 +4721,6 @@ bool skl_ddb_allocation_overlaps(const struct skl_ddb_entry **entries,
>> >>> > > > > return false;
>> >>> > > > > }
>> >>> > > > >
>> >>> > > > > -static int
>> >>> > > > > -skl_ddb_add_affected_planes(struct intel_crtc_state *cstate,
>> >>> > > > > - const struct skl_pipe_wm *old_pipe_wm,
>> >>> > > > > - const struct skl_pipe_wm *pipe_wm)
>> >>> > > > > -{
>> >>> > > > > - struct drm_atomic_state *state = cstate->base.state;
>> >>> > > > > - struct drm_device *dev = state->dev;
>> >>> > > > > - struct drm_crtc *crtc = cstate->base.crtc;
>> >>> > > > > - struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
>> >>> > > > > - struct drm_i915_private *dev_priv = to_i915(dev);
>> >>> > > > > - struct intel_atomic_state *intel_state = to_intel_atomic_state(state);
>> >>> > > > > - struct skl_ddb_allocation *new_ddb = &intel_state->wm_results.ddb;
>> >>> > > > > - struct skl_ddb_allocation *cur_ddb = &dev_priv->wm.skl_hw.ddb;
>> >>> > > > > - struct drm_plane_state *plane_state;
>> >>> > > > > - struct drm_plane *plane;
>> >>> > > > > - enum pipe pipe = intel_crtc->pipe;
>> >>> > > > > -
>> >>> > > > > - WARN_ON(!drm_atomic_get_existing_crtc_state(state, crtc));
>> >>> > > > > -
>> >>> > > > > - drm_for_each_plane_mask(plane, dev, cstate->base.plane_mask) {
>> >>> > > > > - enum plane_id plane_id = to_intel_plane(plane)->id;
>> >>> > > > > - const struct skl_plane_wm *wm = &pipe_wm->planes[plane_id];
>> >>> > > > > - const struct skl_plane_wm *old_wm = &old_pipe_wm->planes[plane_id];
>> >>> > > > > -
>> >>> > > > > - if ((skl_ddb_entry_equal(&cur_ddb->plane[pipe][plane_id],
>> >>> > > > > - &new_ddb->plane[pipe][plane_id]) &&
>> >>> > > > > - skl_ddb_entry_equal(&cur_ddb->y_plane[pipe][plane_id],
>> >>> > > > > - &new_ddb->y_plane[pipe][plane_id])) &&
>> >>> > > > > - !memcmp(wm, old_wm, sizeof(struct skl_plane_wm)))
>> >>> > > > > - continue;
>> >>> > > > > -
>> >>> > > > > - plane_state = drm_atomic_get_plane_state(state, plane);
>> >>> > > > > - if (IS_ERR(plane_state))
>> >>> > > > > - return PTR_ERR(plane_state);
>> >>> > > > > - }
>> >>> > > > > -
>> >>> > > > > - return 0;
>> >>> > > > > -}
>> >>> > > > > -
>> >>> > > > > static int skl_update_pipe_wm(struct drm_crtc_state *cstate,
>> >>> > > > > const struct skl_pipe_wm *old_pipe_wm,
>> >>> > > > > struct skl_pipe_wm *pipe_wm, /* out */
>> >>> > > > > @@ -4826,17 +4734,6 @@ static int skl_update_pipe_wm(struct drm_crtc_state *cstate,
>> >>> > > > > if (ret)
>> >>> > > > > return ret;
>> >>> > > > >
>> >>> > > > > - ret = skl_allocate_pipe_ddb(intel_cstate, pipe_wm, ddb);
>> >>> > > > > - if (ret)
>> >>> > > > > - return ret;
>> >>> > > > > - /*
>> >>> > > > > - * TODO: Planes are included in state to arm WM registers.
>> >>> > > > > - * Scope to optimize further, by just rewriting plane surf register.
>> >>> > > > > - */
>> >>> > > > > - ret = skl_ddb_add_affected_planes(intel_cstate, old_pipe_wm, pipe_wm);
>> >>> > > > > - if (ret)
>> >>> > > > > - return ret;
>> >>> > > > > -
>> >>> > > > > if (!memcmp(old_pipe_wm, pipe_wm, sizeof(*pipe_wm)))
>> >>> > > > > *changed = false;
>> >>> > > > > else
>> >>> > > > > @@ -4859,7 +4756,41 @@ static int skl_update_pipe_wm(struct drm_crtc_state *cstate,
>> >>> > > > > }
>> >>> > > > >
>> >>> > > > > static int
>> >>> > > > > -skl_include_affected_crtcs(struct drm_atomic_state *state)
>> >>> > > > > +skl_ddb_add_affected_planes(struct intel_crtc_state *cstate)
>> >>> > > > > +{
>> >>> > > > > + struct drm_atomic_state *state = cstate->base.state;
>> >>> > > > > + struct drm_device *dev = state->dev;
>> >>> > > > > + struct drm_crtc *crtc = cstate->base.crtc;
>> >>> > > > > + struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
>> >>> > > > > + struct drm_i915_private *dev_priv = to_i915(dev);
>> >>> > > > > + struct intel_atomic_state *intel_state = to_intel_atomic_state(state);
>> >>> > > > > + struct skl_ddb_allocation *new_ddb = &intel_state->wm_results.ddb;
>> >>> > > > > + struct skl_ddb_allocation *cur_ddb = &dev_priv->wm.skl_hw.ddb;
>> >>> > > > > + struct drm_plane_state *plane_state;
>> >>> > > > > + struct drm_plane *plane;
>> >>> > > > > + enum pipe pipe = intel_crtc->pipe;
>> >>> > > > > +
>> >>> > > > > + WARN_ON(!drm_atomic_get_existing_crtc_state(state, crtc));
>> >>> > > > > +
>> >>> > > > > + drm_for_each_plane_mask(plane, dev, cstate->base.plane_mask) {
>> >>> > > > > + enum plane_id plane_id = to_intel_plane(plane)->id;
>> >>> > > > > +
>> >>> > > > > + if (skl_ddb_entry_equal(&cur_ddb->plane[pipe][plane_id],
>> >>> > > > > + &new_ddb->plane[pipe][plane_id]) &&
>> >>> > > > > + skl_ddb_entry_equal(&cur_ddb->y_plane[pipe][plane_id],
>> >>> > > > > + &new_ddb->y_plane[pipe][plane_id]))
>> >>> > > > > + continue;
>> >>> > > > > +
>> >>> > > > > + plane_state = drm_atomic_get_plane_state(state, plane);
>> >>> > > > > + if (IS_ERR(plane_state))
>> >>> > > > > + return PTR_ERR(plane_state);
>> >>> > > > > + }
>> >>> > > > > +
>> >>> > > > > + return 0;
>> >>> > > > > +}
>> >>> > > > > +
>> >>> > > > > +static int
>> >>> > > > > +skl_compute_ddb(struct drm_atomic_state *state)
>> >>> > > > > {
>> >>> > > > > struct drm_device *dev = state->dev;
>> >>> > > > > struct drm_i915_private *dev_priv = to_i915(dev);
>> >>> > > > > @@ -4923,6 +4854,14 @@ static int skl_update_pipe_wm(struct drm_crtc_state *cstate,
>> >>> > > > > cstate = intel_atomic_get_crtc_state(state, intel_crtc);
>> >>> > > > > if (IS_ERR(cstate))
>> >>> > > > > return PTR_ERR(cstate);
>> >>> > > > > +
>> >>> > > > > + ret = skl_allocate_pipe_ddb(cstate, ddb);
>> >>> > > > > + if (ret)
>> >>> > > > > + return ret;
>> >>> > > > > +
>> >>> > > > > + ret = skl_ddb_add_affected_planes(cstate);
>> >>> > > > > + if (ret)
>> >>> > > > > + return ret;
>> >>> > > > > }
>> >>> > > > >
>> >>> > > > > return 0;
>> >>> > > > > @@ -5012,7 +4951,7 @@ static int skl_update_pipe_wm(struct drm_crtc_state *cstate,
>> >>> > > > > /* Clear all dirty flags */
>> >>> > > > > results->dirty_pipes = 0;
>> >>> > > > >
>> >>> > > > > - ret = skl_include_affected_crtcs(state);
>> >>> > > > > + ret = skl_compute_ddb(state);
>> >>> > > > > if (ret)
>> >>> > > > > return ret;
>> >>> > > > >
>> >>> > > > > --
>> >>> > > > > 1.9.1
>> >>> > > > >
>> >>> > > >
>> >>> > > > --
>> >>> > > > Matt Roper
>> >>> > > > Graphics Software Engineer
>> >>> > > > IoTG Platform Enabling & Development
>> >>> > > > Intel Corporation
>> >>> > > > (916) 356-2795
>> >>> > > > _______________________________________________
>> >>> > > > Intel-gfx mailing list
>> >>> > > > Intel-gfx at lists.freedesktop.org
>> >>> > > > https://lists.freedesktop.org/mailman/listinfo/intel-gfx
>> >>> > >
>> >>> > >
>> >>> >
>> >>> > _______________________________________________
>> >>> > Intel-gfx mailing list
>> >>> > Intel-gfx at lists.freedesktop.org
>> >>> > https://lists.freedesktop.org/mailman/listinfo/intel-gfx
>> >>>
>> >>>
>> >> _______________________________________________
>> >> Intel-gfx mailing list
>> >> Intel-gfx at lists.freedesktop.org
>> >> https://lists.freedesktop.org/mailman/listinfo/intel-gfx
>> >
>> > --
>> > Jani Nikula, Intel Open Source Technology Center
>>
>>
>>
>> --
>> Rodrigo Vivi
>> Blog: http://blog.vivi.eng.br
>
> --
> Matt Roper
> Graphics Software Engineer
> IoTG Platform Enabling & Development
> Intel Corporation
> (916) 356-2795
--
Rodrigo Vivi
Blog: http://blog.vivi.eng.br
More information about the Intel-gfx
mailing list