[Intel-gfx] [PATCH v7 9/9] drm/i915: Set PWM divider to match desired frequency in vbt
Pandiyan, Dhinakaran
dhinakaran.pandiyan at intel.com
Tue May 16 06:21:04 UTC 2017
On Mon, 2017-05-15 at 17:43 -0700, Puthikorn Voravootivat wrote:
>
>
> On Mon, May 15, 2017 at 4:07 PM, Pandiyan, Dhinakaran
> <dhinakaran.pandiyan at intel.com> wrote:
> On Fri, 2017-05-12 at 17:31 -0700, Puthikorn Voravootivat
> wrote:
> >
> >
> >
> > On Fri, May 12, 2017 at 5:12 PM, Pandiyan, Dhinakaran
> > <dhinakaran.pandiyan at intel.com> wrote:
> > On Thu, 2017-05-11 at 16:02 -0700, Puthikorn
> Voravootivat
> > wrote:
> > > Read desired PWM frequency from panel vbt and
> calculate the
> > > value for divider in DPCD address 0x724 and 0x728
> to have
> > > as many bits as possible for PWM duty cyle for
> granularity
> > of
> > > brightness adjustment while the frequency is still
> within
> > 25%
> > > of the desired frequency.
> >
> > I read a few eDP panel data sheets, the PWM
> frequencies all
> > start from
> > ~200Hz. If the VBT chooses this lowest value to
> allow for more
> > brightness control, and then this patch lowers the
> value by
> > another 25%,
> > we'll end up below the panel allowed PWM frequency.
> >
> > In fact, one of the systems I checked had PWM
> frequency as
> > 200Hz in VBT
> > and the panel datasheet also had PWM frequency range
> starting
> > from
> > 200Hz. Have you considered this case?
> >
> > The spec said "A given LCD panel typically has a limited
> range of
> > backlight frequency capability.
> > To limit the programmable frequency range, limitations are
> placed on
> > the allowable total divider ratio with the Sink device"
> > So I think it should be auto cap to 200Hz in this case.
> >
> > -DK
> > >
> > > Signed-off-by: Puthikorn Voravootivat
> <puthik at chromium.org>
> > > ---
> > > drivers/gpu/drm/i915/intel_dp_aux_backlight.c |
> 81
> > +++++++++++++++++++++++++++
> > > 1 file changed, 81 insertions(+)
> > >
> > > diff --git
> a/drivers/gpu/drm/i915/intel_dp_aux_backlight.c
> > b/drivers/gpu/drm/i915/intel_dp_aux_backlight.c
> > > index 0b48851013cc..6f10a2f1ab76 100644
> > > ---
> a/drivers/gpu/drm/i915/intel_dp_aux_backlight.c
> > > +++
> b/drivers/gpu/drm/i915/intel_dp_aux_backlight.c
> > > @@ -113,12 +113,86 @@
> > intel_dp_aux_set_dynamic_backlight_percent(struct
> intel_dp
> > *intel_dp,
> > > }
> > > }
> > >
> > > +/*
> > > + * Set PWM Frequency divider to match desired
> frequency in
> > vbt.
> > > + * The PWM Frequency is calculated as 27Mhz / (F
> x P).
> > > + * - Where F = PWM Frequency Pre-Divider value
> programmed
> > by field 7:0 of the
> > > + * EDP_BACKLIGHT_FREQ_SET register
> (DPCD
> > Address 00728h)
> > > + * - Where P = 2^Pn, where Pn is the value
> programmed by
> > field 4:0 of the
> > > + * EDP_PWMGEN_BIT_COUNT register
> (DPCD Address
> > 00724h)
> > > + */
> > > +static void intel_dp_aux_set_pwm_freq(struct
> > intel_connector *connector)
> > > +{
> > > + struct drm_i915_private *dev_priv =
> > to_i915(connector->base.dev);
> > > + struct intel_dp *intel_dp =
> > enc_to_intel_dp(&connector->encoder->base);
> > > + int freq, fxp, fxp_min, fxp_max, fxp_actual,
> f = 1;
> > > + u8 pn, pn_min, pn_max;
> > > +
> > > + /* Find desired value of (F x P)
> > > + * Note that, if F x P is out of supported
> range, the
> > maximum value or
> > > + * minimum value will applied automatically.
> So no
> > need to check that.
> > > + */
> > > + freq = dev_priv->vbt.backlight.pwm_freq_hz;
> > > + DRM_DEBUG_KMS("VBT defined backlight
> frequency %u Hz
> > \n", freq);
> > > + if (!freq) {
> > > + DRM_DEBUG_KMS("Use panel default
> backlight
> > frequency\n");
> > > + return;
> > > + }
> > > +
> > > + fxp = KHz(DP_EDP_BACKLIGHT_FREQ_BASE_KHZ) /
> freq;
> > > +
> > > + /* Use highest possible value of Pn for more
> > granularity of brightness
> > > + * adjustment while satifying the conditions
> below.
> > > + * - Pn is in the range of Pn_min and Pn_max
> > > + * - F is in the range of 1 and 255
> > > + * - Effective frequency is within 25% of
> desired
> > frequency.
> > > + */
> > > + if (drm_dp_dpcd_readb(&intel_dp->aux,
> > > +
> > DP_EDP_PWMGEN_BIT_COUNT_CAP_MIN, &pn_min) != 1) {
> > > + DRM_DEBUG_KMS("Failed to read pwmgen
> bit count
> > cap min\n");
> > > + return;
> > > + }
> > > + if (drm_dp_dpcd_readb(&intel_dp->aux,
> > > +
> > DP_EDP_PWMGEN_BIT_COUNT_CAP_MAX, &pn_max) != 1) {
> > > + DRM_DEBUG_KMS("Failed to read pwmgen
> bit count
> > cap max\n");
> > > + return;
> > > + }
> > > + pn_min &= DP_EDP_PWMGEN_BIT_COUNT_MASK;
> > > + pn_max &= DP_EDP_PWMGEN_BIT_COUNT_MASK;
> > > +
> > > + fxp_min = fxp * 3 / 4;
> > > + fxp_max = fxp * 5 / 4;
> >
> >
> > You are allowing fxp between +/- 25% of the actual.
> This isn't
> > same as
> > the "Effective frequency is within 25% of desired
> frequency."
> > right? The
> > frequency can vary between -20% and +33%.
> >
> >
> > You are right.
> > You want me to change commit message to reflect this or
> change the
> > code to
> > match the commit message?
>
>
> I am okay with fixing the comment and commit message. Is the
> 25%
> arbitrary or based on the distances between the possible
> values? Please
> make a note in the comment if it's the former.
>
>
> > > + if (fxp_min < (1 << pn_min) || (255 <<
> pn_max) <
> > fxp_max) {
>
>
>
> > > + DRM_DEBUG_KMS("VBT defined backlight
> frequency
> > out of range\n");
> > > + return;
> > > + }
> > > +
> > > + for (pn = pn_max; pn > pn_min; pn--) {
>
> Is there a reason this is not pn >= pn_min?
> This is bug because f value will be incorrect in the case that pn ==
> pn_min.
> Thanks for catching this.
>
Isn't that a side-effect using the right shift operation for division?
Would DIV_ROUND_CLOSEST allow you to use pn_min?
>
> > > + f = clamp(fxp >> pn, 1, 255);
> > > + fxp_actual = f << pn;
> > > + if (fxp_min <= fxp_actual &&
> fxp_actual <=
> > fxp_max)
> > > + break;
> > > + }
> > > +
> > > + if (drm_dp_dpcd_writeb(&intel_dp->aux,
> > > +
> DP_EDP_PWMGEN_BIT_COUNT, pn) <
> > 0) {
> > > + DRM_DEBUG_KMS("Failed to write aux
> pwmgen bit
> > count\n");
>
>
> If the number of brightness control bits are changing, the
> max.
> brightness value changes too.
>
> Please see intel_dp_aux_setup_backlight().
>
>
> I think this is fine because
> - intel_dp_aux_setup_backlight() will
> called intel_dp_aux_enable_backlight() which
> called intel_dp_aux_set_pwm_freq() first before determine the max
> brightness value.
> - Also, the panel I tested does not change
> BACKLIGHT_BRIGHTNESS_BYTE_COUNT
>
> when changing the frequency.
The only values I see being set for max brightness are 0xFFFF and 0xFF
if (intel_dp->edp_dpcd[2] & DP_EDP_BACKLIGHT_BRIGHTNESS_BYTE_COUNT)
panel->backlight.max = 0xFFFF;
else
panel->backlight.max = 0xFF;
I can't see where you are setting this based on Pn. Can you please point
out? From what I understand, max should be 2^Pn.
Also, won't this function be called every time _enable_backlight() is
called? Isn't doing this from setup sufficient? I guess, fixing it is an
optimization that'd be nice to have but not necessary.
>
>
> > > + return;
> > > + }
> > > + if (drm_dp_dpcd_writeb(&intel_dp->aux,
> > > +
> DP_EDP_BACKLIGHT_FREQ_SET, (u8)
> > f) < 0) {
> > > + DRM_DEBUG_KMS("Failed to write aux
> backlight
> > freq\n");
> > > + return;
> > > + }
> > > +}
> > > +
> > > static void intel_dp_aux_enable_backlight(struct
> > intel_connector *connector)
> > > {
> > > struct intel_dp *intel_dp =
> > enc_to_intel_dp(&connector->encoder->base);
> > > uint8_t dpcd_buf = 0;
> > > uint8_t new_dpcd_buf = 0;
> > > uint8_t edp_backlight_mode = 0;
> > > + bool freq_cap;
> > >
> > > if (drm_dp_dpcd_readb(&intel_dp->aux,
> > >
> DP_EDP_BACKLIGHT_MODE_SET_REGISTER,
> > &dpcd_buf) != 1) {
> > > @@ -151,6 +225,10 @@ static void
> > intel_dp_aux_enable_backlight(struct intel_connector
> > *connector)
> > > DRM_DEBUG_KMS("Enable dynamic
> brightness.\n");
> > > }
> > >
> > > + freq_cap = intel_dp->edp_dpcd[2] &
> > DP_EDP_BACKLIGHT_FREQ_AUX_SET_CAP;
> > > + if (freq_cap)
> > > + new_dpcd_buf |=
> > DP_EDP_BACKLIGHT_FREQ_AUX_SET_ENABLE;
> > > +
> > > if (new_dpcd_buf != dpcd_buf) {
> > > if
> (drm_dp_dpcd_writeb(&intel_dp->aux,
> > >
> DP_EDP_BACKLIGHT_MODE_SET_REGISTER,
> > new_dpcd_buf) < 0) {
> > > @@ -158,6 +236,9 @@ static void
> > intel_dp_aux_enable_backlight(struct intel_connector
> > *connector)
> > > }
> > > }
> > >
> > > + if (freq_cap)
> > > +
> intel_dp_aux_set_pwm_freq(connector);
> > > +
> > > set_aux_backlight_enable(intel_dp, true);
> > > intel_dp_aux_set_backlight(connector,
> > connector->panel.backlight.level);
> > > }
> >
> >
> >
> >
>
> > _______________________________________________
> > Intel-gfx mailing list
> > Intel-gfx at lists.freedesktop.org
> > https://lists.freedesktop.org/mailman/listinfo/intel-gfx
>
>
>
> _______________________________________________
> Intel-gfx mailing list
> Intel-gfx at lists.freedesktop.org
> https://lists.freedesktop.org/mailman/listinfo/intel-gfx
More information about the Intel-gfx
mailing list