[Intel-gfx] [PATCH 40/67] drm/i915/cnl: Enable loadgen_select bit for vswing sequence

[Manasi Navare]

On Thu, Apr 06, 2017 at 12:15:36PM -0700, Rodrigo Vivi wrote:
> From: Clint Taylor <clinton.a.taylor at intel.com>
> 
> vswing programming sequence step 2 requires the Loadgen_select bit to
> be set in PORT_TX_DW4 lane reigsters per table defined by Bit rate and
> lane width. Implemented the change that was marked as FIXME in the
> driver.
> 
> v2: (Rodrigo) checkpatch fixes.
> 
> Signed-off-by: Clint Taylor <clinton.a.taylor at intel.com>
> Signed-off-by: Rodrigo Vivi <rodrigo.vivi at intel.com>
 Reviewed-by: Manasi Navare <manasi.d.navare at intel.com>

> ---
>  drivers/gpu/drm/i915/intel_ddi.c | 38 ++++++++++++++++++++++++++++++++------
>  1 file changed, 32 insertions(+), 6 deletions(-)
> 
> diff --git a/drivers/gpu/drm/i915/intel_ddi.c b/drivers/gpu/drm/i915/intel_ddi.c
> index a4d7061..3f461c3 100644
> --- a/drivers/gpu/drm/i915/intel_ddi.c
> +++ b/drivers/gpu/drm/i915/intel_ddi.c
> @@ -1846,10 +1846,24 @@ static void cnl_ddi_vswing_program(struct drm_i915_private *dev_priv,
>  	I915_WRITE(CNL_PORT_TX_DW7_GRP(port), val);
>  }
>  
> -static void cnl_ddi_vswing_sequence(struct drm_i915_private *dev_priv,
> -				    u32 level, enum port port, int type)
> +static void cnl_ddi_vswing_sequence(struct intel_encoder *encoder, u32 level)
>  {
> +	struct drm_i915_private *dev_priv = to_i915(encoder->base.dev);
> +	struct intel_dp *intel_dp = enc_to_intel_dp(&encoder->base);
> +	enum port port = intel_ddi_get_encoder_port(encoder);
> +	int type = encoder->type;
> +	int width = 0;
> +	int rate = 0;
>  	u32 val;
> +	int ln = 0;
> +
> +	if ((intel_dp) && (type == INTEL_OUTPUT_EDP || type == INTEL_OUTPUT_DP)) {
> +		width = intel_dp->lane_count;
> +		rate = intel_dp->link_rate;
> +	} else {
> +		width = 4;
> +		/* Rate is always < than 6GHz for HDMI */
> +	}
>  
>  	/*
>  	 * 1. If port type is eDP or DP,
> @@ -1865,8 +1879,21 @@ static void cnl_ddi_vswing_sequence(struct drm_i915_private *dev_priv,
>  
>  	/* 2. Program loadgen select */
>  	/*
> -	 * FIXME: Program PORT_TX_DW4_LN depending on Bit rate and used lanes
> +	 * Program PORT_TX_DW4_LN depending on Bit rate and used lanes
> +	 * <= 6 GHz and 4 lanes (LN0=0, LN1=1, LN2=1, LN3=1)
> +	 * <= 6 GHz and 1,2 lanes (LN0=0, LN1=1, LN2=1, LN3=0)
> +	 * > 6 GHz (LN0=0, LN1=0, LN2=0, LN3=0)
>  	 */
> +	for (ln = 0; ln <= 3; ln++) {
> +		val = I915_READ(CNL_PORT_TX_DW4_LN(port, ln));
> +		val &= ~LOADGEN_SELECT;
> +
> +		if (((rate < 600000) && (width == 4) && (ln >= 1))  ||
> +		    ((rate < 600000) && (width < 4) && ((ln == 1) || (ln == 2)))) {
> +			val |= LOADGEN_SELECT;
> +		}

Verified this from the Bspec values of loadgen_select for specific link rate
and lane count.

Manasi
> +		I915_WRITE(CNL_PORT_TX_DW4_LN(port, ln), val);
> +	}
>  
>  	/* 3. Set PORT_CL_DW5 SUS Clock Config to 11b */
>  	val = I915_READ(CNL_PORT_CL1CM_DW5);
> @@ -1920,7 +1947,7 @@ uint32_t ddi_signal_levels(struct intel_dp *intel_dp)
>  	else if (IS_GEN9_LP(dev_priv))
>  		bxt_ddi_vswing_sequence(dev_priv, level, port, encoder->type);
>  	else if (IS_CANNONLAKE(dev_priv)) {
> -		cnl_ddi_vswing_sequence(dev_priv, level, port, encoder->type);
> +		cnl_ddi_vswing_sequence(encoder, level);
>  		/* DDI_BUF_CTL bits 27:24 are reserved on CNL */
>  		return 0;
>  	}
> @@ -2022,8 +2049,7 @@ static void intel_ddi_pre_enable_hdmi(struct intel_encoder *encoder,
>  		bxt_ddi_vswing_sequence(dev_priv, level, port,
>  					INTEL_OUTPUT_HDMI);
>  	else if (IS_CANNONLAKE(dev_priv))
> -		cnl_ddi_vswing_sequence(dev_priv, level, port,
> -					INTEL_OUTPUT_HDMI);
> +		cnl_ddi_vswing_sequence(encoder, level);
>  
>  	intel_hdmi->set_infoframes(drm_encoder,
>  				   has_hdmi_sink,
> -- 
> 1.9.1
> 
> _______________________________________________
> Intel-gfx mailing list
> Intel-gfx at lists.freedesktop.org
> https://lists.freedesktop.org/mailman/listinfo/intel-gfx