[Intel-gfx] [PATCH 2/2] drm/i915/glk: Enable cold boot for GLK DSI
Jani Nikula
jani.nikula at intel.com
Tue May 30 07:03:59 UTC 2017
On Wed, 24 May 2017, "Chauhan, Madhav" <madhav.chauhan at intel.com> wrote:
>> -----Original Message-----
>> From: Nikula, Jani
>> Sent: Wednesday, May 24, 2017 7:22 PM
>> To: Chauhan, Madhav <madhav.chauhan at intel.com>; Ville Syrjälä
>> <ville.syrjala at linux.intel.com>
>> Cc: intel-gfx at lists.freedesktop.org; Conselvan De Oliveira, Ander
>> <ander.conselvan.de.oliveira at intel.com>; Hiremath, Shashidhar
>> <shashidhar.hiremath at intel.com>
>> Subject: RE: [Intel-gfx] [PATCH 2/2] drm/i915/glk: Enable cold boot for GLK
>> DSI
>>
>> On Mon, 15 May 2017, "Chauhan, Madhav" <madhav.chauhan at intel.com>
>> wrote:
>> >> -----Original Message-----
>> >> From: Nikula, Jani
>> >> Sent: Monday, May 15, 2017 9:19 PM
>> >> To: Ville Syrjälä <ville.syrjala at linux.intel.com>; Chauhan, Madhav
>> >> <madhav.chauhan at intel.com>
>> >> Cc: intel-gfx at lists.freedesktop.org; Conselvan De Oliveira, Ander
>> >> <ander.conselvan.de.oliveira at intel.com>; Hiremath, Shashidhar
>> >> <shashidhar.hiremath at intel.com>
>> >> Subject: Re: [Intel-gfx] [PATCH 2/2] drm/i915/glk: Enable cold boot
>> >> for GLK DSI
>> >>
>> >> On Tue, 09 May 2017, Ville Syrjälä <ville.syrjala at linux.intel.com> wrote:
>> >> > On Tue, May 09, 2017 at 06:59:25PM +0530, Madhav Chauhan wrote:
>> >> >> As per BSEPC, if device ready bit is '0' in enable IO sequence
>> >> >> then its a cold boot/reset scenario eg: S3/S4 resume. In these
>> >> >> conditions we need to program certain registers and prepare port
>> >> >> from the middle of DSI enable sequence otherwise feature like S3/S4
>> doesn't work.
>> >> >
>> >> > Can't we just always follow the "cold boot" sequence? Less
>> >> > codepaths means less bugs.
>> >>
>> >> I agree. Madhav?
>> >
>> > Cold Boot scenario represents when DSI controller/IO is not initialized
>> even once before use eg:
>> > 1. Connected HDMI boot with DSI panel
>> > 2. S3/S4
>> > While normal scenario is:
>> > 1. Boot with DSI panel without HDMI. DSI will be initialized once by
>> > GOP/BIOS
>> >
>> > If we use cold boot sequence always, normal scenario doesn’t work as
>> > few registers can’t be Programmed as per cold boot scenario. LP_WAKE bit
>> (MIPI_CTRL REG) is one of the example.
>> >
>> > Moreover, current changes works very well for all above scenarios :).
>>
>> Well, no. There's a very limited set of registers that can and must only be
>> programmed in the "cold boot" case. This patch moves all of
>> intel_dsi_prepare() for glk to only be done in the cold boot case, but there's a
>> load of registers that aren't restricted in this way, and need to be
>> programmed on enable regardless of device ready. Seems to me the change
>> here is too coarse grained.
>
> Actually when we do GLK_MIPIIO_ENABLE in device_ready all the
> registers are restored back When DSI is enabled after disable through
> software *IF* power is not lost(normal scenario) so we can opt out not
> to program during normal scenario. Found this in my testing. Will
> confirm this with HW team.
>
> While for cold boot scenario where power is lost during S3/S4, we need
> to program all these registers And unfortunately when we program
> *ONLY* register mentioned in BSPEC in device_ready DSI is not up and
> Need to program all registers here itself to make it work.
But this assumes that on enable, when power has not been lost, all the
registers contain the correct information already. We can't rely on
that.
BR,
Jani.
>
>>
>> BR,
>> Jani.
>>
>> >
>> >>
>> >> BR,
>> >> Jani.
>> >>
>> >>
>> >> >
>> >> >>
>> >> >> Signed-off-by: Madhav Chauhan <madhav.chauhan at intel.com>
>> >> >> ---
>> >> >> drivers/gpu/drm/i915/intel_dsi.c | 79
>> >> >> ++++++++++++++++++++++++----------------
>> >> >> 1 file changed, 48 insertions(+), 31 deletions(-)
>> >> >>
>> >> >> diff --git a/drivers/gpu/drm/i915/intel_dsi.c
>> >> >> b/drivers/gpu/drm/i915/intel_dsi.c
>> >> >> index fc0ef49..6b68864 100644
>> >> >> --- a/drivers/gpu/drm/i915/intel_dsi.c
>> >> >> +++ b/drivers/gpu/drm/i915/intel_dsi.c
>> >> >> @@ -346,12 +346,17 @@ static bool intel_dsi_compute_config(struct
>> >> intel_encoder *encoder,
>> >> >> return true;
>> >> >> }
>> >> >>
>> >> >> -static void glk_dsi_device_ready(struct intel_encoder *encoder)
>> >> >> +static void intel_dsi_prepare(struct intel_encoder *intel_encoder,
>> >> >> + struct intel_crtc_state *pipe_config);
>> >> >> +
>> >> >> +static void glk_dsi_device_ready(struct intel_encoder *encoder,
>> >> >> + struct intel_crtc_state *pipe_config)
>> >> >> {
>> >> >> struct drm_i915_private *dev_priv = to_i915(encoder->base.dev);
>> >> >> struct intel_dsi *intel_dsi = enc_to_intel_dsi(&encoder->base);
>> >> >> enum port port;
>> >> >> u32 tmp, val;
>> >> >> + bool cold_boot = false;
>> >> >>
>> >> >> /* Set the MIPI mode
>> >> >> * If MIPI_Mode is off, then writing to LP_Wake bit is not reflecting.
>> >> >> @@ -370,7 +375,10 @@ static void glk_dsi_device_ready(struct
>> >> intel_encoder *encoder)
>> >> >> /* Program LP Wake */
>> >> >> for_each_dsi_port(port, intel_dsi->ports) {
>> >> >> tmp = I915_READ(MIPI_CTRL(port));
>> >> >> - tmp |= GLK_LP_WAKE;
>> >> >> + if (!(I915_READ(MIPI_DEVICE_READY(port)) &
>> >> DEVICE_READY))
>> >> >> + tmp &= ~GLK_LP_WAKE;
>> >> >> + else
>> >> >> + tmp |= GLK_LP_WAKE;
>> >> >> I915_WRITE(MIPI_CTRL(port), tmp);
>> >> >> }
>> >> >>
>> >> >> @@ -382,6 +390,15 @@ static void glk_dsi_device_ready(struct
>> >> intel_encoder *encoder)
>> >> >> DRM_ERROR("MIPIO port is powergated\n");
>> >> >> }
>> >> >>
>> >> >> + /* Check if cold boot scenario */
>> >> >> + for_each_dsi_port(port, intel_dsi->ports) {
>> >> >> + cold_boot |= !(I915_READ(MIPI_DEVICE_READY(port)) &
>> >> >> + DEVICE_READY);
>> >> >> + }
>> >> >> +
>> >> >> + if (cold_boot)
>> >> >> + intel_dsi_prepare(encoder, pipe_config);
>> >> >> +
>> >> >> /* Wait for MIPI PHY status bit to set */
>> >> >> for_each_dsi_port(port, intel_dsi->ports) {
>> >> >> if (intel_wait_for_register(dev_priv,
>> >> >> @@ -402,34 +419,34 @@ static void glk_dsi_device_ready(struct
>> >> intel_encoder *encoder)
>> >> >> val |= DEVICE_READY;
>> >> >> I915_WRITE(MIPI_DEVICE_READY(port), val);
>> >> >> usleep_range(10, 15);
>> >> >> - }
>> >> >> -
>> >> >> - /* Enter ULPS */
>> >> >> - val = I915_READ(MIPI_DEVICE_READY(port));
>> >> >> - val &= ~ULPS_STATE_MASK;
>> >> >> - val |= (ULPS_STATE_ENTER | DEVICE_READY);
>> >> >> - I915_WRITE(MIPI_DEVICE_READY(port), val);
>> >> >> + } else {
>> >> >> + /* Enter ULPS */
>> >> >> + val = I915_READ(MIPI_DEVICE_READY(port));
>> >> >> + val &= ~ULPS_STATE_MASK;
>> >> >> + val |= (ULPS_STATE_ENTER | DEVICE_READY);
>> >> >> + I915_WRITE(MIPI_DEVICE_READY(port), val);
>> >> >>
>> >> >> - /* Wait for ULPS active */
>> >> >> - if (intel_wait_for_register(dev_priv,
>> >> >> + /* Wait for ULPS active */
>> >> >> + if (intel_wait_for_register(dev_priv,
>> >> >> MIPI_CTRL(port), GLK_ULPS_NOT_ACTIVE, 0,
>> >> 20))
>> >> >> - DRM_ERROR("ULPS not active\n");
>> >> >> + DRM_ERROR("ULPS not active\n");
>> >> >>
>> >> >> - /* Exit ULPS */
>> >> >> - val = I915_READ(MIPI_DEVICE_READY(port));
>> >> >> - val &= ~ULPS_STATE_MASK;
>> >> >> - val |= (ULPS_STATE_EXIT | DEVICE_READY);
>> >> >> - I915_WRITE(MIPI_DEVICE_READY(port), val);
>> >> >> + /* Exit ULPS */
>> >> >> + val = I915_READ(MIPI_DEVICE_READY(port));
>> >> >> + val &= ~ULPS_STATE_MASK;
>> >> >> + val |= (ULPS_STATE_EXIT | DEVICE_READY);
>> >> >> + I915_WRITE(MIPI_DEVICE_READY(port), val);
>> >> >>
>> >> >> - /* Enter Normal Mode */
>> >> >> - val = I915_READ(MIPI_DEVICE_READY(port));
>> >> >> - val &= ~ULPS_STATE_MASK;
>> >> >> - val |= (ULPS_STATE_NORMAL_OPERATION | DEVICE_READY);
>> >> >> - I915_WRITE(MIPI_DEVICE_READY(port), val);
>> >> >> + /* Enter Normal Mode */
>> >> >> + val = I915_READ(MIPI_DEVICE_READY(port));
>> >> >> + val &= ~ULPS_STATE_MASK;
>> >> >> + val |= (ULPS_STATE_NORMAL_OPERATION |
>> >> DEVICE_READY);
>> >> >> + I915_WRITE(MIPI_DEVICE_READY(port), val);
>> >> >>
>> >> >> - tmp = I915_READ(MIPI_CTRL(port));
>> >> >> - tmp &= ~GLK_LP_WAKE;
>> >> >> - I915_WRITE(MIPI_CTRL(port), tmp);
>> >> >> + tmp = I915_READ(MIPI_CTRL(port));
>> >> >> + tmp &= ~GLK_LP_WAKE;
>> >> >> + I915_WRITE(MIPI_CTRL(port), tmp);
>> >> >> + }
>> >> >> }
>> >> >>
>> >> >> /* Wait for Stop state */
>> >> >> @@ -515,7 +532,8 @@ static void vlv_dsi_device_ready(struct
>> >> intel_encoder *encoder)
>> >> >> }
>> >> >> }
>> >> >>
>> >> >> -static void intel_dsi_device_ready(struct intel_encoder *encoder)
>> >> >> +static void intel_dsi_device_ready(struct intel_encoder *encoder,
>> >> >> + struct intel_crtc_state *pipe_config)
>> >> >> {
>> >> >> struct drm_i915_private *dev_priv = to_i915(encoder->base.dev);
>> >> >>
>> >> >> @@ -524,7 +542,7 @@ static void intel_dsi_device_ready(struct
>> >> intel_encoder *encoder)
>> >> >> else if (IS_BROXTON(dev_priv))
>> >> >> bxt_dsi_device_ready(encoder);
>> >> >> else if (IS_GEMINILAKE(dev_priv))
>> >> >> - glk_dsi_device_ready(encoder);
>> >> >> + glk_dsi_device_ready(encoder, pipe_config);
>> >> >> }
>> >> >>
>> >> >> static void glk_dsi_enter_low_power_mode(struct intel_encoder
>> >> >> *encoder) @@ -710,8 +728,6 @@ static void
>> >> >> intel_dsi_port_disable(struct
>> >> intel_encoder *encoder)
>> >> >> }
>> >> >> }
>> >> >>
>> >> >> -static void intel_dsi_prepare(struct intel_encoder *intel_encoder,
>> >> >> - struct intel_crtc_state *pipe_config);
>> >> >> static void intel_dsi_unprepare(struct intel_encoder *encoder);
>> >> >>
>> >> >> static void intel_dsi_msleep(struct intel_dsi *intel_dsi, int
>> >> >> msec) @@ -800,7 +816,8 @@ static void intel_dsi_pre_enable(struct
>> >> intel_encoder *encoder,
>> >> >> I915_WRITE(DSPCLK_GATE_D, val);
>> >> >> }
>> >> >>
>> >> >> - intel_dsi_prepare(encoder, pipe_config);
>> >> >> + if (!IS_GEMINILAKE(dev_priv))
>> >> >> + intel_dsi_prepare(encoder, pipe_config);
>> >> >>
>> >> >> /* Power on, try both CRC pmic gpio and VBT */
>> >> >> if (intel_dsi->gpio_panel)
>> >> >> @@ -812,7 +829,7 @@ static void intel_dsi_pre_enable(struct
>> >> intel_encoder *encoder,
>> >> >> intel_dsi_vbt_exec_sequence(intel_dsi, MIPI_SEQ_DEASSERT_RESET);
>> >> >>
>> >> >> /* Put device in ready state (LP-11) */
>> >> >> - intel_dsi_device_ready(encoder);
>> >> >> + intel_dsi_device_ready(encoder, pipe_config);
>> >> >>
>> >> >> /* Send initialization commands in LP mode */
>> >> >> intel_dsi_vbt_exec_sequence(intel_dsi, MIPI_SEQ_INIT_OTP);
>> >> >> --
>> >> >> 1.9.1
>> >> >>
>> >> >> _______________________________________________
>> >> >> Intel-gfx mailing list
>> >> >> Intel-gfx at lists.freedesktop.org
>> >> >> https://lists.freedesktop.org/mailman/listinfo/intel-gfx
>> >>
>> >> --
>> >> Jani Nikula, Intel Open Source Technology Center
>>
>> --
>> Jani Nikula, Intel Open Source Technology Center
--
Jani Nikula, Intel Open Source Technology Center
More information about the Intel-gfx
mailing list