[Intel-gfx] [PATCH v2 1/3] drm/i915: Make ips_enabled a property depending on whether IPS is enabled, v2.
Ville Syrjälä
ville.syrjala at linux.intel.com
Mon Nov 20 14:01:44 UTC 2017
On Mon, Nov 20, 2017 at 01:23:35PM +0100, Maarten Lankhorst wrote:
> ips_enabled was used as a variable of whether IPS can be enabled or not,
> but should be used to test whether IPS is actually enabled.
>
> Changes since v1:
> - Call needs_modeset on new crtc state. (Ville)
> - IPS can be enabled with sprite plane enabled too. (Ville)
> - Fix CDCLK vs IPS workaround. (Ville)
>
> Signed-off-by: Maarten Lankhorst <maarten.lankhorst at linux.intel.com>
> ---
> drivers/gpu/drm/i915/intel_cdclk.c | 2 +-
> drivers/gpu/drm/i915/intel_display.c | 119 +++++++++++++++++++---------------
> drivers/gpu/drm/i915/intel_drv.h | 1 +
> drivers/gpu/drm/i915/intel_pipe_crc.c | 2 -
> 4 files changed, 67 insertions(+), 57 deletions(-)
>
> diff --git a/drivers/gpu/drm/i915/intel_cdclk.c b/drivers/gpu/drm/i915/intel_cdclk.c
> index e8884c2ade98..30affa7903d7 100644
> --- a/drivers/gpu/drm/i915/intel_cdclk.c
> +++ b/drivers/gpu/drm/i915/intel_cdclk.c
> @@ -1896,7 +1896,7 @@ int intel_crtc_compute_min_cdclk(const struct intel_crtc_state *crtc_state)
> min_cdclk = intel_pixel_rate_to_cdclk(dev_priv, crtc_state->pixel_rate);
>
> /* pixel rate mustn't exceed 95% of cdclk with IPS on BDW */
> - if (IS_BROADWELL(dev_priv) && crtc_state->ips_enabled)
> + if (IS_BROADWELL(dev_priv) && hsw_pipe_config_ips_capable(crtc_state))
> min_cdclk = DIV_ROUND_UP(min_cdclk * 100, 95);
I think either we should drop this entirely and make the
ips_compute_config() check logical.cdclk instead of max_cdclk,
or we stick to the max_cdclk based check but move it into
hsw_pipe_config_ips_capable(). Otherwise we would end up
rejecting any mode whose pixel rate exceed the 95% cdclk
limit.
>
> /* BSpec says "Do not use DisplayPort with CDCLK less than 432 MHz,
> diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c
> index 3b3dec1e6640..0b9ba415839a 100644
> --- a/drivers/gpu/drm/i915/intel_display.c
> +++ b/drivers/gpu/drm/i915/intel_display.c
> @@ -4870,7 +4870,7 @@ void hsw_enable_ips(const struct intel_crtc_state *crtc_state)
> struct drm_device *dev = crtc->base.dev;
> struct drm_i915_private *dev_priv = to_i915(dev);
>
> - if (!crtc->config->ips_enabled)
> + if (!crtc_state->ips_enabled)
> return;
>
> /*
> @@ -4966,14 +4966,6 @@ intel_post_enable_primary(struct drm_crtc *crtc,
> struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
> int pipe = intel_crtc->pipe;
>
> - /*
> - * FIXME IPS should be fine as long as one plane is
> - * enabled, but in practice it seems to have problems
> - * when going from primary only to sprite only and vice
> - * versa.
> - */
> - hsw_enable_ips(new_crtc_state);
> -
> /*
> * Gen2 reports pipe underruns whenever all planes are disabled.
> * So don't enable underrun reporting before at least some planes
> @@ -4989,10 +4981,9 @@ intel_post_enable_primary(struct drm_crtc *crtc,
> intel_check_pch_fifo_underruns(dev_priv);
> }
>
> -/* FIXME move all this to pre_plane_update() with proper state tracking */
> +/* FIXME get rid of this and use pre_plane_update */
> static void
> -intel_pre_disable_primary(struct drm_crtc *crtc,
> - const struct intel_crtc_state *old_crtc_state)
> +intel_pre_disable_primary_noatomic(struct drm_crtc *crtc)
> {
> struct drm_device *dev = crtc->dev;
> struct drm_i915_private *dev_priv = to_i915(dev);
> @@ -5001,32 +4992,12 @@ intel_pre_disable_primary(struct drm_crtc *crtc,
>
> /*
> * Gen2 reports pipe underruns whenever all planes are disabled.
> - * So diasble underrun reporting before all the planes get disabled.
> - * FIXME: Need to fix the logic to work when we turn off all planes
> - * but leave the pipe running.
> + * So disable underrun reporting before all the planes get disabled.
> */
> if (IS_GEN2(dev_priv))
> intel_set_cpu_fifo_underrun_reporting(dev_priv, pipe, false);
>
> - /*
> - * FIXME IPS should be fine as long as one plane is
> - * enabled, but in practice it seems to have problems
> - * when going from primary only to sprite only and vice
> - * versa.
> - */
> - hsw_disable_ips(old_crtc_state);
> -}
> -
> -/* FIXME get rid of this and use pre_plane_update */
> -static void
> -intel_pre_disable_primary_noatomic(struct drm_crtc *crtc)
> -{
> - struct drm_device *dev = crtc->dev;
> - struct drm_i915_private *dev_priv = to_i915(dev);
> - struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
> - int pipe = intel_crtc->pipe;
> -
> - intel_pre_disable_primary(crtc, to_intel_crtc_state(crtc->state));
> + hsw_disable_ips(to_intel_crtc_state(crtc->state));
>
> /*
> * Vblank time updates from the shadow to live plane control register
> @@ -5058,6 +5029,11 @@ static void intel_post_plane_update(struct intel_crtc_state *old_crtc_state)
> if (pipe_config->update_wm_post && pipe_config->base.active)
> intel_update_watermarks(crtc);
>
> + if (!old_crtc_state->ips_enabled ||
> + needs_modeset(&pipe_config->base) ||
> + pipe_config->update_pipe)
Hmm. So thinking more about this I guess I figured out why you put the
update_pipe check here. On BDW the initial old_crtc_state will have
ips_enabled=true since the readout now always makes it so. Thus if we
skip the initial modeset we would not turn on IPS even if a suitable
set of planes is enabled.
I think it would be more clear to check for the INHERITED thing
specifically. Also that would avoid paying the cost of the pcode
access every time we have update_pipe==true and ips_enabled==true.
> + hsw_enable_ips(pipe_config);
> +
> if (old_pri_state) {
> struct intel_plane_state *primary_state =
> intel_atomic_get_new_plane_state(to_intel_atomic_state(old_state),
> @@ -5088,6 +5064,9 @@ static void intel_pre_plane_update(struct intel_crtc_state *old_crtc_state,
> struct intel_atomic_state *old_intel_state =
> to_intel_atomic_state(old_state);
>
> + if (needs_modeset(&pipe_config->base) || !pipe_config->ips_enabled)
> + hsw_disable_ips(old_crtc_state);
> +
> if (old_pri_state) {
> struct intel_plane_state *primary_state =
> intel_atomic_get_new_plane_state(old_intel_state,
> @@ -5096,10 +5075,13 @@ static void intel_pre_plane_update(struct intel_crtc_state *old_crtc_state,
> to_intel_plane_state(old_pri_state);
>
> intel_fbc_pre_update(crtc, pipe_config, primary_state);
> -
> - if (old_primary_state->base.visible &&
> + /*
> + * Gen2 reports pipe underruns whenever all planes are disabled.
> + * So disable underrun reporting before all the planes get disabled.
> + */
> + if (IS_GEN2(dev_priv) && old_primary_state->base.visible &&
> (modeset || !primary_state->base.visible))
> - intel_pre_disable_primary(&crtc->base, old_crtc_state);
> + intel_set_cpu_fifo_underrun_reporting(dev_priv, crtc->pipe, false);
> }
>
> /*
> @@ -6228,15 +6210,42 @@ static int ironlake_fdi_compute_config(struct intel_crtc *intel_crtc,
> return ret;
> }
>
> -static bool pipe_config_supports_ips(struct drm_i915_private *dev_priv,
> - struct intel_crtc_state *pipe_config)
> +bool hsw_pipe_config_ips_capable(const struct intel_crtc_state *pipe_config)
> {
> - if (pipe_config->ips_force_disable)
> + struct intel_crtc *crtc = to_intel_crtc(pipe_config->base.crtc);
> +
> + /* IPS only exists on ULT machines and is tied to pipe A. */
> + if (!hsw_crtc_supports_ips(crtc))
> + return false;
> +
> + if (!i915_modparams.enable_ips)
> return false;
>
> if (pipe_config->pipe_bpp > 24)
> return false;
>
> + return true;
> +}
> +
> +static bool hsw_compute_ips_config(struct intel_crtc_state *pipe_config)
> +{
> + struct drm_i915_private *dev_priv = to_i915(pipe_config->base.crtc->dev);
> +
> + if (!hsw_pipe_config_ips_capable(pipe_config))
> + return false;
> +
> + if (pipe_config->ips_force_disable)
> + return false;
> +
> + /*
> + * FIXME IPS should be fine as long as one plane is
> + * enabled, but in practice it seems to have problems
> + * when going from primary only to sprite only and vice
> + * versa.
> + */
> + if (!(pipe_config->active_planes & BIT(PLANE_PRIMARY)))
> + return false;
> +
> /* HSW can handle pixel rate up to cdclk? */
> if (IS_HASWELL(dev_priv))
> return true;
> @@ -6252,17 +6261,6 @@ static bool pipe_config_supports_ips(struct drm_i915_private *dev_priv,
> dev_priv->max_cdclk_freq * 95 / 100;
> }
>
> -static void hsw_compute_ips_config(struct intel_crtc *crtc,
> - struct intel_crtc_state *pipe_config)
> -{
> - struct drm_device *dev = crtc->base.dev;
> - struct drm_i915_private *dev_priv = to_i915(dev);
> -
> - pipe_config->ips_enabled = i915_modparams.enable_ips &&
> - hsw_crtc_supports_ips(crtc) &&
> - pipe_config_supports_ips(dev_priv, pipe_config);
> -}
> -
> static bool intel_crtc_supports_double_wide(const struct intel_crtc *crtc)
> {
> const struct drm_i915_private *dev_priv = to_i915(crtc->base.dev);
> @@ -6378,9 +6376,6 @@ static int intel_crtc_compute_config(struct intel_crtc *crtc,
>
> intel_crtc_compute_pixel_rate(pipe_config);
>
> - if (HAS_IPS(dev_priv))
> - hsw_compute_ips_config(crtc, pipe_config);
> -
> if (pipe_config->has_pch_encoder)
> return ironlake_fdi_compute_config(crtc, pipe_config);
>
> @@ -9275,6 +9270,19 @@ static bool haswell_get_pipe_config(struct intel_crtc *crtc,
> ironlake_get_pfit_config(crtc, pipe_config);
> }
>
> + if (hsw_crtc_supports_ips(crtc)) {
> + if (IS_HASWELL(dev_priv))
> + pipe_config->ips_enabled = I915_READ(IPS_CTL) & IPS_ENABLE;
> + else {
> + /*
> + * We cannot readout IPS state on broadwell, set to
> + * true so we can set it to a defined state on first
> + * commit.
> + */
> + pipe_config->ips_enabled = true;
> + }
> + }
> +
> if (pipe_config->cpu_transcoder != TRANSCODER_EDP &&
> !transcoder_is_dsi(pipe_config->cpu_transcoder)) {
> pipe_config->pixel_multiplier =
> @@ -10488,6 +10496,9 @@ static int intel_crtc_atomic_check(struct drm_crtc *crtc,
> pipe_config);
> }
>
> + if (HAS_IPS(dev_priv))
> + pipe_config->ips_enabled = hsw_compute_ips_config(pipe_config);
> +
> return ret;
> }
>
> diff --git a/drivers/gpu/drm/i915/intel_drv.h b/drivers/gpu/drm/i915/intel_drv.h
> index 69aab324aaa1..40417b20844e 100644
> --- a/drivers/gpu/drm/i915/intel_drv.h
> +++ b/drivers/gpu/drm/i915/intel_drv.h
> @@ -1485,6 +1485,7 @@ bool bxt_find_best_dpll(struct intel_crtc_state *crtc_state, int target_clock,
> int chv_calc_dpll_params(int refclk, struct dpll *pll_clock);
>
> bool intel_crtc_active(struct intel_crtc *crtc);
> +bool hsw_pipe_config_ips_capable(const struct intel_crtc_state *pipe_config);
> void hsw_enable_ips(const struct intel_crtc_state *crtc_state);
> void hsw_disable_ips(const struct intel_crtc_state *crtc_state);
> enum intel_display_power_domain intel_port_to_power_domain(enum port port);
> diff --git a/drivers/gpu/drm/i915/intel_pipe_crc.c b/drivers/gpu/drm/i915/intel_pipe_crc.c
> index 61641d479b93..1f5cd572a7ff 100644
> --- a/drivers/gpu/drm/i915/intel_pipe_crc.c
> +++ b/drivers/gpu/drm/i915/intel_pipe_crc.c
> @@ -541,8 +541,6 @@ static void hsw_pipe_A_crc_wa(struct drm_i915_private *dev_priv,
> * completely disable it.
> */
> pipe_config->ips_force_disable = enable;
> - if (pipe_config->ips_enabled == enable)
> - pipe_config->base.connectors_changed = true;
> }
>
> if (IS_HASWELL(dev_priv)) {
> --
> 2.15.0
>
> _______________________________________________
> Intel-gfx mailing list
> Intel-gfx at lists.freedesktop.org
> https://lists.freedesktop.org/mailman/listinfo/intel-gfx
--
Ville Syrjälä
Intel OTC
More information about the Intel-gfx
mailing list