[Intel-gfx] [PATCH i-g-t 1/2] kms_plane: Enumerate outputs before planes in position subtests

[Imre Deak]

Enumerating outputs before planes allows us to calculate the reference
CRC only once for each subtest instead of calculating it for each plane
tested. This removes an extra modeset during the test of each plane,
speeding up things, especially on internal panels with long power
cycle delays.

In addition when testing multiple outputs we'll now test all planes for
a given output in one go, so we can avoid the full modeset we currently
have when switching from one output to another when testing a given
plane.

While at it remove the redundant igt_skip_on() for non-existant pipes
and planes, we check for these already earlier.

Signed-off-by: Imre Deak <imre.deak at intel.com>
---
 tests/kms_plane.c | 55 +++++++++++++++++++++++--------------------------------
 1 file changed, 23 insertions(+), 32 deletions(-)

diff --git a/tests/kms_plane.c b/tests/kms_plane.c
index 81249750..640356e8 100644
--- a/tests/kms_plane.c
+++ b/tests/kms_plane.c
@@ -152,9 +152,9 @@ test_plane_position_with_output(data_t *data,
 				enum pipe pipe,
 				int plane,
 				igt_output_t *output,
+				igt_crc_t *reference_crc,
 				unsigned int flags)
 {
-	test_position_t test = { .data = data };
 	igt_plane_t *primary, *sprite;
 	struct igt_fb primary_fb, sprite_fb;
 	drmModeModeInfo *mode;
@@ -163,10 +163,6 @@ test_plane_position_with_output(data_t *data,
 	igt_info("Testing connector %s using pipe %s plane %d\n",
 		 igt_output_name(output), kmstest_pipe_name(pipe), plane);
 
-	test_init(data, pipe);
-
-	test_grab_crc(data, output, pipe, &green, &test.reference_crc);
-
 	igt_output_set_pipe(output, pipe);
 
 	mode = igt_output_get_mode(output);
@@ -206,7 +202,7 @@ test_plane_position_with_output(data_t *data,
 	igt_pipe_crc_collect_crc(data->pipe_crc, &crc2);
 
 	if (flags & TEST_POSITION_FULLY_COVERED)
-		igt_assert_crc_equal(&test.reference_crc, &crc);
+		igt_assert_crc_equal(reference_crc, &crc);
 	else {
 		;/* FIXME: missing reference CRCs */
 	}
@@ -218,23 +214,29 @@ test_plane_position_with_output(data_t *data,
 
 	/* reset the constraint on the pipe */
 	igt_output_set_pipe(output, PIPE_ANY);
-
-	test_fini(data);
 }
 
 static void
-test_plane_position(data_t *data, enum pipe pipe, int plane,
-		    unsigned int flags)
+test_plane_position(data_t *data, enum pipe pipe, unsigned int flags)
 {
 	igt_output_t *output;
 	int connected_outs = 0;
 
-	igt_skip_on(pipe >= data->display.n_pipes);
-	igt_skip_on(plane >= data->display.pipes[pipe].n_planes);
-
 	for_each_valid_output_on_pipe(&data->display, pipe, output) {
-		test_plane_position_with_output(data, pipe, plane, output,
-						flags);
+		int n_planes = data->display.pipes[pipe].n_planes;
+		igt_crc_t reference_crc;
+
+		test_init(data, pipe);
+
+		test_grab_crc(data, output, pipe, &green, &reference_crc);
+
+		for (int plane = 1; plane < n_planes; plane++)
+			test_plane_position_with_output(data, pipe, plane,
+							output, &reference_crc,
+							flags);
+
+		test_fini(data);
+
 		connected_outs++;
 	}
 
@@ -373,27 +375,16 @@ run_tests_for_pipe_plane(data_t *data, enum pipe pipe)
 	}
 
 	igt_subtest_f("plane-position-covered-pipe-%s-planes",
-		      kmstest_pipe_name(pipe)) {
-		int n_planes = data->display.pipes[pipe].n_planes;
-		for (int plane = 1; plane < n_planes; plane++)
-			test_plane_position(data, pipe, plane,
-					    TEST_POSITION_FULLY_COVERED);
-	}
+		      kmstest_pipe_name(pipe))
+		test_plane_position(data, pipe, TEST_POSITION_FULLY_COVERED);
 
 	igt_subtest_f("plane-position-hole-pipe-%s-planes",
-		      kmstest_pipe_name(pipe)) {
-		int n_planes = data->display.pipes[pipe].n_planes;
-		for (int plane = 1; plane < n_planes; plane++)
-			test_plane_position(data, pipe, plane, 0);
-	}
+		      kmstest_pipe_name(pipe))
+		test_plane_position(data, pipe, 0);
 
 	igt_subtest_f("plane-position-hole-dpms-pipe-%s-planes",
-		      kmstest_pipe_name(pipe)) {
-		int n_planes = data->display.pipes[pipe].n_planes;
-		for (int plane = 1; plane < n_planes; plane++)
-			test_plane_position(data, pipe, plane,
-					    TEST_DPMS);
-	}
+		      kmstest_pipe_name(pipe))
+		test_plane_position(data, pipe, TEST_DPMS);
 
 	igt_subtest_f("plane-panning-top-left-pipe-%s-planes",
 		      kmstest_pipe_name(pipe)) {
-- 
2.11.0