[Intel-gfx] [PATCH 07/13] drm/i915/cnl: DVFS for PLL enabling

[Manasi Navare]

On Tue, Oct 03, 2017 at 12:06:08AM -0700, Rodrigo Vivi wrote:
> From: "Kahola, Mika" <mika.kahola at intel.com>
> 
> Display Voltage and Frequency Switching (DVFS) is used to adjust the
> display voltage to match the display clock frequencies. If voltage is
> set too low, it will break functionality. If voltage is set too high,
> it will waste power. Voltage level is selected based on CD clock and
> DDI clock.
> 
> The sequence before frequency change is the following and it requests
> the power controller to raise voltage to maximum
> 
> - Ensure any previous GT Driver Mailbox transaction is complete.
> - Write GT Driver Mailbox Data Low = 0x3.
> - Write GT Driver Mailbox Data High = 0x0.
> - Write GT Driver Mailbox Interface = 0x80000007.
> - Poll GT Driver Mailbox Interface for Run/Busy indication cleared (bit 31 = 0).
> - Read GT Driver Mailbox Data Low, if bit 0 is 0x1, continue, else restart the sequence.
>   Timeout after 3ms
> 
> The sequence after frequency change is the following and it requests
> the port controller to raise voltage to the requested level.
> 
> - Write GT Driver Mailbox Data Low
>  * For level 0, write 0x0
>  * For level 1, write 0x1
>  * For level 2, write 0x2
>  * For level 3, write 0x3
>    - Write GT Driver Mailbox Data High = 0x0.
>    - Write GT Driver Mailbox Interface = 0x80000007.
> 
> For Cannonlake, the level 3 is not used and it aliases to level 2.
> 
> v2: reuse Paulo's work on cdclk. This patch depends on Paulo's patch
>     [PATCH 02/12] drm/i915/cnl: extract cnl_dvfs_{pre,post}_change
> v3: (By Rodrigo): Remove duplicated commend and fix typo on Paulo's name.
> v4: (By Rodrigo): Rebase on top "Unify and export gen9+ port_clock calculation"
>     The port clock calculation here was only addressing DP, so let's reuse
>     the current port calculation that is already in place without any duplication.
>     Alos fix portclk <= 594000 instead of portclk < 594000.
> 
> Cc: Paulo Zanoni <paulo.r.zanoni at intel.com>
> Cc: Ville Syrjälä <ville.syrjala at linux.intel.com>
> Signed-off-by: Kahola, Mika <mika.kahola at intel.com>
> Signed-off-by: Rodrigo Vivi <rodrigo.vivi at intel.com>

Looks good, dowble checked with the voltage levels from the spec.

Reviewed-by: Manasi Navare <manasi.d.navare at intel.com>

> ---
>  drivers/gpu/drm/i915/intel_dpll_mgr.c | 30 ++++++++++++++++++++++--------
>  1 file changed, 22 insertions(+), 8 deletions(-)
> 
> diff --git a/drivers/gpu/drm/i915/intel_dpll_mgr.c b/drivers/gpu/drm/i915/intel_dpll_mgr.c
> index a2a3d93d67bd..6030fbafa580 100644
> --- a/drivers/gpu/drm/i915/intel_dpll_mgr.c
> +++ b/drivers/gpu/drm/i915/intel_dpll_mgr.c
> @@ -1966,10 +1966,23 @@ static const struct intel_dpll_mgr bxt_pll_mgr = {
>  	.dump_hw_state = bxt_dump_hw_state,
>  };
>  
> +static int cnl_get_dvfs_level(int cdclk, int portclk)
> +{
> +	if (cdclk == 168000 && portclk <= 594000)
> +		return 0;
> +	else if (cdclk == 336000 && portclk <= 594000)
> +		return 1;
> +	else
> +		return 2;
> +}
> +
>  static void cnl_ddi_pll_enable(struct drm_i915_private *dev_priv,
>  			       struct intel_shared_dpll *pll)
>  {
>  	uint32_t val;
> +	int ret;
> +	int level;
> +	int cdclk, portclk;
>  
>  	/* 1. Enable DPLL power in DPLL_ENABLE. */
>  	val = I915_READ(CNL_DPLL_ENABLE(pll->id));
> @@ -2006,11 +2019,9 @@ static void cnl_ddi_pll_enable(struct drm_i915_private *dev_priv,
>  	/*
>  	 * 5. If the frequency will result in a change to the voltage
>  	 * requirement, follow the Display Voltage Frequency Switching
> -	 * Sequence Before Frequency Change
> -	 *
> -	 * FIXME: (DVFS) is used to adjust the display voltage to match the
> -	 * display clock frequencies
> +	 * (DVFS) Sequence Before Frequency Change
>  	 */
> +	ret = cnl_dvfs_pre_change(dev_priv);
>  
>  	/* 6. Enable DPLL in DPLL_ENABLE. */
>  	val = I915_READ(CNL_DPLL_ENABLE(pll->id));
> @@ -2028,11 +2039,14 @@ static void cnl_ddi_pll_enable(struct drm_i915_private *dev_priv,
>  	/*
>  	 * 8. If the frequency will result in a change to the voltage
>  	 * requirement, follow the Display Voltage Frequency Switching
> -	 * Sequence After Frequency Change
> -	 *
> -	 * FIXME: (DVFS) is used to adjust the display voltage to match the
> -	 * display clock frequencies
> +	 * (DVFS) Sequence After Frequency Change
>  	 */
> +	if (ret == 0) {
> +		cdclk = dev_priv->cdclk.hw.cdclk;
> +		portclk = intel_ddi_port_clock(dev_priv, pll->id);
> +		level = cnl_get_dvfs_level(cdclk, portclk);
> +		cnl_dvfs_post_change(dev_priv, level);
> +	}
>  
>  	/*
>  	 * 9. turn on the clock for the DDI and map the DPLL to the DDI
> -- 
> 2.13.5
> 
> _______________________________________________
> Intel-gfx mailing list
> Intel-gfx at lists.freedesktop.org
> https://lists.freedesktop.org/mailman/listinfo/intel-gfx