[Intel-gfx] [PATCH i-g-t v3 2/2] tests/pm_backlight: Enable connected output to allow tests to succeed, v4.

[Ville Syrjälä]

On Thu, Oct 12, 2017 at 12:55:39PM +0200, Maarten Lankhorst wrote:
> If the connected output is disabled before this test is run, then the test
> will fail because actual_brightness stays at 0 instead of the value
> of the desired brightness. Fix this by reading intel_backlight/device
> for the output name, and enable that output at start of this test.
> 
> Changes since v1:
> - Enable the connected output, instead of enabling all outputs.
> Changes since v2:
> - Set a dummy fb, just in case.
> Changes since v3:
> - Use igt_output_get_plane_type, not get_plane.
> 
> Sample failure:
> IGT-Version: 1.20-g01c550a27986 (x86_64) (Linux: 4.14.0-rc3-fbconhax+ x86_64)
> (pm_backlight:1203) CRITICAL: Test assertion failure function test_and_verify, file pm_backlight.c:111:
> (pm_backlight:1203) CRITICAL: Failed assertion: ({ typeof(0) _a = (0); typeof(val - tolerance) _b = (val - tolerance); _a > _b ? _a : _b; }) <= result
> (pm_backlight:1203) CRITICAL: error: 91200 > 0
> 
> Signed-off-by: Maarten Lankhorst <maarten.lankhorst at linux.intel.com>
> ---
>  tests/pm_backlight.c | 47 +++++++++++++++++++++++++++++++++++++++++++++++
>  1 file changed, 47 insertions(+)
> 
> diff --git a/tests/pm_backlight.c b/tests/pm_backlight.c
> index 8258d4e4c124..a695f90913fd 100644
> --- a/tests/pm_backlight.c
> +++ b/tests/pm_backlight.c
> @@ -155,13 +155,56 @@ igt_main
>  {
>  	struct context context = {0};
>  	int old;
> +	igt_display_t display;
> +	struct igt_fb fb;
>  
>  	igt_skip_on_simulation();
>  
>  	igt_fixture {
> +		enum pipe pipe;
> +		igt_output_t *output;
> +		bool found = false;
> +		char full_name[32] = {};
> +		char *name;
> +		drmModeModeInfo *mode;
> +		igt_plane_t *primary;
> +
>  		/* Get the max value and skip the whole test if sysfs interface not available */
>  		igt_skip_on(backlight_read(&old, "brightness"));
>  		igt_assert(backlight_read(&context.max, "max_brightness") > -1);
> +
> +		/*
> +		 * Backlight tests requires the output to be enabled,
> +		 * try to enable all.
> +		 */
> +		kmstest_set_vt_graphics_mode();
> +		igt_display_init(&display, drm_open_driver(DRIVER_INTEL));
> +
> +		/* should be ../../cardX-$output */
> +		igt_assert_lt(12, readlink(BACKLIGHT_PATH "/device", full_name, sizeof(full_name) - 1));
> +		name = basename(full_name);
> +
> +		for_each_pipe_with_valid_output(&display, pipe, output) {
> +			if (strcmp(name + 6, output->name))

This string magic isn't all that clear here. I think it would have been
cleaner to iterate all connected outputs and look for the backlight
under each. But I can't be bothered to care that much so

Reviewed-by: Ville Syrjälä <ville.syrjala at linux.intel.com>

> +				continue;
> +
> +			found = true;
> +			break;
> +		}
> +
> +		igt_assert_f(found, "Could not map \"%s\" to output (%s?)\n", name, name + 6);
> +
> +		igt_output_set_pipe(output, pipe);
> +		mode = igt_output_get_mode(output);
> +
> +		igt_create_pattern_fb(display.drm_fd,
> +				      mode->hdisplay, mode->vdisplay,
> +				      DRM_FORMAT_XRGB8888,
> +				      LOCAL_DRM_FORMAT_MOD_NONE, &fb);
> +		primary = igt_output_get_plane_type(output, DRM_PLANE_TYPE_PRIMARY);
> +		igt_plane_set_fb(primary, &fb);
> +
> +		igt_display_commit2(&display, display.is_atomic ? COMMIT_ATOMIC : COMMIT_LEGACY);
>  	}
>  
>  	igt_subtest("basic-brightness")
> @@ -174,5 +217,9 @@ igt_main
>  	igt_fixture {
>  		/* Restore old brightness */
>  		backlight_write(old, "brightness");
> +
> +		igt_display_fini(&display);
> +		igt_remove_fb(display.drm_fd, &fb);
> +		close(display.drm_fd);
>  	}
>  }
> -- 
> 2.14.1
> 
> _______________________________________________
> Intel-gfx mailing list
> Intel-gfx at lists.freedesktop.org
> https://lists.freedesktop.org/mailman/listinfo/intel-gfx

-- 
Ville Syrjälä
Intel OTC