[Intel-gfx] [PATCH] drm/i915/dp: Send DPCD ON for MST before phy_up

[Dhinakaran Pandiyan]

On Thu, 2018-04-05 at 19:38 +0300, Ville Syrjälä wrote:
> On Wed, Apr 04, 2018 at 07:27:21PM -0400, Lyude Paul wrote:
> > As it turns out, the aux block being off was not the real problem here,
> > as transition from D3 to D0 is mandated by the DP spec to take a maximum
> > of 1ms, whereas we're allowed a 100ms timeframe to respond to ESI irqs.
> > The real problem here is a bit more subtle.
> > 
> > When doing a modeset where the problem of the sink timing out to our
> > sideband requests when transitioning from D3 to D0 occurs, the timeout
> > is from the aux block not coming on. However, nothing else times out
> > other than the initial phy_up message because the DPCD on call in
> > intel_ddi_enable_dp() ends up waking up the AUX block on the hub, not
> > the phy_up sideband message. 


This is the case only when intel_dp_sink_dpms(DRM_MODE_DPMS_OFF) was the
last action. With power_down_phy in post_disable() and power_up_phy in
pre_enable(), we weren't seeing this issue.




> This means that the real fix we need is to
> > use the DPMS on before sending a phy_up to ensure that the hub is ready
> > to accept sideband messages.
> > 
> > Signed-off-by: Lyude Paul <lyude at redhat.com>
> > Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan at intel.com>
> > Cc: Ville Syrjälä <ville.syrjala at linux.intel.com>
> > Cc: Laura Abbott <labbott at redhat.com>
> > Cc: stable at vger.kernel.org
> > Fixes: ad260ab32a4d9 ("drm/i915/dp: Write to SET_POWER dpcd to enable MST hub.")
> > ---
> >  drivers/gpu/drm/i915/intel_ddi.c    | 6 +++++-
> >  drivers/gpu/drm/i915/intel_dp_mst.c | 1 +
> >  2 files changed, 6 insertions(+), 1 deletion(-)
> > 
> > diff --git a/drivers/gpu/drm/i915/intel_ddi.c b/drivers/gpu/drm/i915/intel_ddi.c
> > index a6672a9abd85..9bd675f73f7b 100644
> > --- a/drivers/gpu/drm/i915/intel_ddi.c
> > +++ b/drivers/gpu/drm/i915/intel_ddi.c
> > @@ -2324,7 +2324,11 @@ static void intel_ddi_pre_enable_dp(struct intel_encoder *encoder,
> >  		intel_prepare_dp_ddi_buffers(encoder, crtc_state);
> >  
> >  	intel_ddi_init_dp_buf_reg(encoder);
> > -	intel_dp_sink_dpms(intel_dp, DRM_MODE_DPMS_ON);
> > +	/* for MST, we do DPMS_ON outside of here so that DPMS_ON can happen
> > +	 * before drm_dp_send_power_updown_phy()
> > +	 */
> > +	if (!intel_dp->is_mst)
> 
> Just 'is_mst' should do here.
> 
> And in general I'd like to see the enable and disable paths remain
> symmetric. Ie. also move out the dpms call in the disable path (or
> maybe move the phy_power_up/down in?).
> 
> > +		intel_dp_sink_dpms(intel_dp, DRM_MODE_DPMS_ON);
> >  	intel_dp_start_link_train(intel_dp);
> >  	if (port != PORT_A || INTEL_GEN(dev_priv) >= 9)
> >  		intel_dp_stop_link_train(intel_dp);
> > diff --git a/drivers/gpu/drm/i915/intel_dp_mst.c b/drivers/gpu/drm/i915/intel_dp_mst.c
> > index c3de0918ee13..eff9a4eae1f0 100644
> > --- a/drivers/gpu/drm/i915/intel_dp_mst.c
> > +++ b/drivers/gpu/drm/i915/intel_dp_mst.c
> > @@ -223,6 +223,7 @@ static void intel_mst_pre_enable_dp(struct intel_encoder *encoder,
> >  
> >  	DRM_DEBUG_KMS("active links %d\n", intel_dp->active_mst_links);
> >  
> > +	intel_dp_sink_dpms(intel_dp, DRM_MODE_DPMS_ON);
> >  	drm_dp_send_power_updown_phy(&intel_dp->mst_mgr, connector->port, true);
> 
> This could use a comment to remind people that the order does matter.
> 
> >  	if (intel_dp->active_mst_links == 0)
> >  		intel_dig_port->base.pre_enable(&intel_dig_port->base,
> > -- 
> > 2.14.3
>