[Intel-gfx] [PATCH 2/2] drm/i915: Configure SKL+ scaler initial phase correctly
Ville Syrjälä
ville.syrjala at linux.intel.com
Fri Jun 1 15:52:48 UTC 2018
On Thu, May 31, 2018 at 04:20:24AM +0000, Srinivas, Vidya wrote:
> Thank you.
> Reviewed-By: Vidya Srinivas <vidya.srinivas at intel.com>
Thanks. Series pushed to dinq.
>
> > -----Original Message-----
> > From: Ville Syrjala [mailto:ville.syrjala at linux.intel.com]
> > Sent: Tuesday, May 22, 2018 12:26 AM
> > To: intel-gfx at lists.freedesktop.org
> > Cc: Srinivas, Vidya <vidya.srinivas at intel.com>; Maarten Lankhorst
> > <maarten.lankhorst at linux.intel.com>
> > Subject: [PATCH 2/2] drm/i915: Configure SKL+ scaler initial phase correctly
> >
> > From: Ville Syrjälä <ville.syrjala at linux.intel.com>
> >
> > Set up the SKL+ scaler initial phase registers correctly. Otherwise we start
> > fetching the data from the center of the first pixel instead of the top-left
> > corner, which obviously then leads to right/bottom edges replicating data
> > excessively as the data runs out half a pixel too soon.
> >
> > Cc: Vidya Srinivas <vidya.srinivas at intel.com>
> > Cc: Maarten Lankhorst <maarten.lankhorst at linux.intel.com>
> > Signed-off-by: Ville Syrjälä <ville.syrjala at linux.intel.com>
> > ---
> > drivers/gpu/drm/i915/i915_reg.h | 4 ++++
> > drivers/gpu/drm/i915/intel_display.c | 41
> > ++++++++++++++++++++++++++++++++++++
> > drivers/gpu/drm/i915/intel_drv.h | 1 +
> > drivers/gpu/drm/i915/intel_sprite.c | 26 +++++++++++++++++++++--
> > 4 files changed, 70 insertions(+), 2 deletions(-)
> >
> > diff --git a/drivers/gpu/drm/i915/i915_reg.h
> > b/drivers/gpu/drm/i915/i915_reg.h index 196a0eb79272..094527403ede
> > 100644
> > --- a/drivers/gpu/drm/i915/i915_reg.h
> > +++ b/drivers/gpu/drm/i915/i915_reg.h
> > @@ -6774,6 +6774,10 @@ enum {
> > #define _PS_VPHASE_1B 0x68988
> > #define _PS_VPHASE_2B 0x68A88
> > #define _PS_VPHASE_1C 0x69188
> > +#define PS_Y_PHASE(x) ((x) << 16)
> > +#define PS_UV_RGB_PHASE(x) ((x) << 0)
> > +#define PS_PHASE_MASK (0x7fff << 1) /* u2.13 */
> > +#define PS_PHASE_TRIP (1 << 0)
> >
> > #define _PS_HPHASE_1A 0x68194
> > #define _PS_HPHASE_2A 0x68294
> > diff --git a/drivers/gpu/drm/i915/intel_display.c
> > b/drivers/gpu/drm/i915/intel_display.c
> > index 42c1f4a56556..07185644a88a 100644
> > --- a/drivers/gpu/drm/i915/intel_display.c
> > +++ b/drivers/gpu/drm/i915/intel_display.c
> > @@ -4729,6 +4729,39 @@ static void cpt_verify_modeset(struct
> > drm_device *dev, int pipe)
> > }
> > }
> >
> > +/*
> > + * The hardware phase 0.0 refers to the center of the pixel.
> > + * We want to start from the top/left edge which is phase
> > + * -0.5. That matches how the hardware calculates the scaling
> > + * factors (from top-left of the first pixel to bottom-right
> > + * of the last pixel, as opposed to the pixel centers).
> > + *
> > + * For 4:2:0 subsampled chroma planes we obviously have to
> > + * adjust that so that the chroma sample position lands in
> > + * the right spot.
> > + *
> > + * Note that for packed YCbCr 4:2:2 formats there is no way to
> > + * control chroma siting. The hardware simply replicates the
> > + * chroma samples for both of the luma samples, and thus we don't
> > + * actually get the expected MPEG2 chroma siting convention :(
> > + * The same behaviour is observed on pre-SKL platforms as well.
> > + */
> > +u16 skl_scaler_calc_phase(int sub, bool chroma_cosited) {
> > + int phase = -0x8000;
> > + u16 trip = 0;
> > +
> > + if (chroma_cosited)
> > + phase += (sub - 1) * 0x8000 / sub;
> > +
> > + if (phase < 0)
> > + phase = 0x10000 + phase;
> > + else
> > + trip = PS_PHASE_TRIP;
> > +
> > + return ((phase >> 2) & PS_PHASE_MASK) | trip; }
> > +
> > static int
> > skl_update_scaler(struct intel_crtc_state *crtc_state, bool force_detach,
> > unsigned int scaler_user, int *scaler_id, @@ -4928,14
> > +4961,22 @@ static void skylake_pfit_enable(struct intel_crtc *crtc)
> > &crtc->config->scaler_state;
> >
> > if (crtc->config->pch_pfit.enabled) {
> > + u16 uv_rgb_hphase, uv_rgb_vphase;
> > int id;
> >
> > if (WARN_ON(crtc->config->scaler_state.scaler_id < 0))
> > return;
> >
> > + uv_rgb_hphase = skl_scaler_calc_phase(1, false);
> > + uv_rgb_vphase = skl_scaler_calc_phase(1, false);
> > +
> > id = scaler_state->scaler_id;
> > I915_WRITE(SKL_PS_CTRL(pipe, id), PS_SCALER_EN |
> > PS_FILTER_MEDIUM | scaler_state-
> > >scalers[id].mode);
> > + I915_WRITE_FW(SKL_PS_VPHASE(pipe, id),
> > + PS_Y_PHASE(0) |
> > PS_UV_RGB_PHASE(uv_rgb_vphase));
> > + I915_WRITE_FW(SKL_PS_HPHASE(pipe, id),
> > + PS_Y_PHASE(0) |
> > PS_UV_RGB_PHASE(uv_rgb_hphase));
> > I915_WRITE(SKL_PS_WIN_POS(pipe, id), crtc->config-
> > >pch_pfit.pos);
> > I915_WRITE(SKL_PS_WIN_SZ(pipe, id), crtc->config-
> > >pch_pfit.size);
> > }
> > diff --git a/drivers/gpu/drm/i915/intel_drv.h
> > b/drivers/gpu/drm/i915/intel_drv.h
> > index 42a59b7fd736..0f1dbfcf8538 100644
> > --- a/drivers/gpu/drm/i915/intel_drv.h
> > +++ b/drivers/gpu/drm/i915/intel_drv.h
> > @@ -1621,6 +1621,7 @@ void intel_mode_from_pipe_config(struct
> > drm_display_mode *mode, void intel_crtc_arm_fifo_underrun(struct
> > intel_crtc *crtc,
> > struct intel_crtc_state *crtc_state);
> >
> > +u16 skl_scaler_calc_phase(int sub, bool chroma_center);
> > int skl_update_scaler_crtc(struct intel_crtc_state *crtc_state); int
> > skl_max_scale(struct intel_crtc *crtc, struct intel_crtc_state *crtc_state,
> > uint32_t pixel_format);
> > diff --git a/drivers/gpu/drm/i915/intel_sprite.c
> > b/drivers/gpu/drm/i915/intel_sprite.c
> > index 214cc730642c..58522441253d 100644
> > --- a/drivers/gpu/drm/i915/intel_sprite.c
> > +++ b/drivers/gpu/drm/i915/intel_sprite.c
> > @@ -284,13 +284,35 @@ skl_update_plane(struct intel_plane *plane,
> > /* program plane scaler */
> > if (plane_state->scaler_id >= 0) {
> > int scaler_id = plane_state->scaler_id;
> > - const struct intel_scaler *scaler;
> > + const struct intel_scaler *scaler =
> > + &crtc_state->scaler_state.scalers[scaler_id];
> > + u16 y_hphase, uv_rgb_hphase;
> > + u16 y_vphase, uv_rgb_vphase;
> > +
> > + /* TODO: handle sub-pixel coordinates */
> > + if (fb->format->format == DRM_FORMAT_NV12) {
> > + y_hphase = skl_scaler_calc_phase(1, false);
> > + y_vphase = skl_scaler_calc_phase(1, false);
> > +
> > + /* MPEG2 chroma siting convention */
> > + uv_rgb_hphase = skl_scaler_calc_phase(2, true);
> > + uv_rgb_vphase = skl_scaler_calc_phase(2, false);
> > + } else {
> > + /* not used */
> > + y_hphase = 0;
> > + y_vphase = 0;
> >
> > - scaler = &crtc_state->scaler_state.scalers[scaler_id];
> > + uv_rgb_hphase = skl_scaler_calc_phase(1, false);
> > + uv_rgb_vphase = skl_scaler_calc_phase(1, false);
> > + }
> >
> > I915_WRITE_FW(SKL_PS_CTRL(pipe, scaler_id),
> > PS_SCALER_EN | PS_PLANE_SEL(plane_id) |
> > scaler->mode);
> > I915_WRITE_FW(SKL_PS_PWR_GATE(pipe, scaler_id), 0);
> > + I915_WRITE_FW(SKL_PS_VPHASE(pipe, scaler_id),
> > + PS_Y_PHASE(y_vphase) |
> > PS_UV_RGB_PHASE(uv_rgb_vphase));
> > + I915_WRITE_FW(SKL_PS_HPHASE(pipe, scaler_id),
> > + PS_Y_PHASE(y_hphase) |
> > PS_UV_RGB_PHASE(uv_rgb_hphase));
> > I915_WRITE_FW(SKL_PS_WIN_POS(pipe, scaler_id), (crtc_x
> > << 16) | crtc_y);
> > I915_WRITE_FW(SKL_PS_WIN_SZ(pipe, scaler_id),
> > ((crtc_w + 1) << 16)|(crtc_h + 1));
> > --
> > 2.16.1
>
--
Ville Syrjälä
Intel
More information about the Intel-gfx
mailing list