[Intel-gfx] [PATCH 26/24] drm/i915/icl: Add allowed DP rates for Icelake

[Rodrigo Vivi]

On Thu, May 24, 2018 at 04:42:37PM -0700, Paulo Zanoni wrote:
> From: Manasi Navare <manasi.d.navare at intel.com>
> 
> For ICL, on Combo PHY the allowed max rates are:
>  - HBR3 8.1 eDP (DDIA)
>  - HBR2 5.4 DisplayPort (DDIB)
> and for MG PHY/TC DDI Ports allowed DP rates are:
>  - HBR3 8.1 DisplayPort (DP alternate mode, DP over TBT,
>  - DP on legacy connector - DDIC/D/E/F)
> 
> Cc: Rodrigo Vivi <rodrigo.vivi at intel.com>
> Cc: Jani Nikula <jani.nikula at linux.intel.com>
> Cc: James Ausmus <james.ausmus at intel.com>
> Signed-off-by: Manasi Navare <manasi.d.navare at intel.com>
> Signed-off-by: James Ausmus <james.ausmus at intel.com>
> ---
>  drivers/gpu/drm/i915/intel_dp.c | 21 +++++++++++++++++++--
>  1 file changed, 19 insertions(+), 2 deletions(-)
> 
> diff --git a/drivers/gpu/drm/i915/intel_dp.c b/drivers/gpu/drm/i915/intel_dp.c
> index 5109023abe28..3ee8e74cf2b8 100644
> --- a/drivers/gpu/drm/i915/intel_dp.c
> +++ b/drivers/gpu/drm/i915/intel_dp.c
> @@ -419,6 +419,20 @@ static int cnl_max_source_rate(struct intel_dp *intel_dp)
>  	return 810000;
>  }
>  
> +static int icl_max_source_rate(struct intel_dp *intel_dp)
> +{
> +	struct intel_digital_port *dig_port = dp_to_dig_port(intel_dp);
> +	enum port port = dig_port->base.port;
> +
> +	/* On Combo PHY port A max speed is HBR3 for all Vccio voltages
> +	 * and on Combo PHY Port B the maximum supported is HBR2.
> +	 */
> +	if (port == PORT_B)

A more generic way here would be COMBO and !eDP

> +		return 540000;
> +
> +	return 810000;
> +}
> +
>  static void
>  intel_dp_set_source_rates(struct intel_dp *intel_dp)
>  {
> @@ -448,10 +462,13 @@ intel_dp_set_source_rates(struct intel_dp *intel_dp)
>  	/* This should only be done once */
>  	WARN_ON(intel_dp->source_rates || intel_dp->num_source_rates);
>  
> -	if (IS_CANNONLAKE(dev_priv)) {
> +	if (INTEL_GEN(dev_priv) >= 10) {
>  		source_rates = cnl_rates;
>  		size = ARRAY_SIZE(cnl_rates);
> -		max_rate = cnl_max_source_rate(intel_dp);
> +		if (IS_ICELAKE(dev_priv))

and gen >= 11

but changes can be in follow-up work, so

Reviewed-by: Rodrigo Vivi <rodrigo.vivi at intel.com>

> +			max_rate = icl_max_source_rate(intel_dp);
> +		else
> +			max_rate = cnl_max_source_rate(intel_dp);
>  	} else if (IS_GEN9_LP(dev_priv)) {
>  		source_rates = bxt_rates;
>  		size = ARRAY_SIZE(bxt_rates);
> -- 
> 2.14.3
> 
> _______________________________________________
> Intel-gfx mailing list
> Intel-gfx at lists.freedesktop.org
> https://lists.freedesktop.org/mailman/listinfo/intel-gfx