[Intel-gfx] [PATCH v2] drm/i915: Wait for PSR exit before checking for vblank evasion

[Dhinakaran Pandiyan]

On Tue, 2018-06-19 at 14:27 -0700, Dhinakaran Pandiyan wrote:
> On Mon, 2018-05-14 at 13:49 -0700, Tarun Vyas wrote:
> > 
> > The PIPEDSL freezes on PSR entry and if PSR hasn't fully exited,
> > then
> > the pipe_update_start call schedules itself out to check back
> > later.
> > 
> > On ChromeOS-4.4 kernel, which is fairly up-to-date w.r.t drm/i915
> > but
> > lags w.r.t core kernel code, hot plugging an external display
> > triggers
> > tons of "potential atomic update errors" in the dmesg, on *pipe A*.
> > A
> > closer analysis reveals that we try to read the scanline 3 times
> > and
> > eventually timeout, b/c PSR hasn't exited fully leading to a
> > PIPEDSL
> > stuck @ 1599. This issue is not seen on upstream kernels, b/c for
> > *some*
> > reason we loop inside intel_pipe_update start for ~2+ msec which in
> > this
> > case is more than enough to exit PSR fully, hence an *unstuck*
> > PIPEDSL
> > counter, hence no error. On the other hand, the ChromeOS kernel
> > spends
> > ~1.1 msec looping inside intel_pipe_update_start and hence errors
> > out
> > b/c the source is still in PSR.
> > 
> > Regardless, we should wait for PSR exit (if PSR is supported and
> > active
> > on the current pipe) before reading the PIPEDSL, b/c if we haven't
> > fully exited PSR, then checking for vblank evasion isn't actually
> > applicable.
> > 
> > This scenario applies to a configuration with an additional pipe,
> > as of now
> > 
> > Signed-off-by: Tarun Vyas <tarun.vyas at intel.com>
> > ---
> >  drivers/gpu/drm/i915/intel_sprite.c | 7 +++++--
> >  1 file changed, 5 insertions(+), 2 deletions(-)
> > 
> > diff --git a/drivers/gpu/drm/i915/intel_sprite.c
> > b/drivers/gpu/drm/i915/intel_sprite.c
> > index ee23613f9fd4..481d310e5c3b 100644
> > --- a/drivers/gpu/drm/i915/intel_sprite.c
> > +++ b/drivers/gpu/drm/i915/intel_sprite.c
> > @@ -107,14 +107,17 @@ void intel_pipe_update_start(const struct
> > intel_crtc_state *new_crtc_state)
> >  						      VBLANK_EVASI
> > ON
> > _TIME_US);
> >  	max = vblank_start - 1;
> >  
> > -	local_irq_disable();
> > -
> >  	if (min <= 0 || max <= 0)
> >  		return;
> >  
> >  	if (WARN_ON(drm_crtc_vblank_get(&crtc->base)))
> >  		return;
> >  
> > +	if(new_crtc_state->has_psr && dev_priv->psr.active)
> > +		psr_wait_for_idle(dev_priv);
> How about just waiting for PSR_STATUS to idle without grabbing any
> locks or checking whether PSR is active?
> 
> Status should be idle if PSR was disabled or on it's way to becoming
> idle if it was enabled. Even if PSR did get enabled while we are in
> pipe_update_start(), it will not be active as long as VBIs are
> enabled.
> 
Correct me if this was already considered, why not wait until the
scanline counter starts moving? I see we have a 
	intel_wait_for_pipe_scanline_moving(crtc) that's used when the
pipe is enabled.

-DK