[Intel-gfx] [PATCH v6 13/28] drm/i915/dp: Compute DSC pipe config in atomic check

Manasi Navare manasi.d.navare at intel.com
Mon Oct 29 21:42:45 UTC 2018


On Mon, Oct 29, 2018 at 10:30:39PM +0200, Ville Syrjälä wrote:
> On Wed, Oct 24, 2018 at 03:28:25PM -0700, Manasi Navare wrote:
> > DSC params like the enable, compressed bpp, slice count and
> > dsc_split are added to the intel_crtc_state. These parameters
> > are set based on the requested mode and available link parameters
> > during the pipe configuration in atomic check phase.
> > These values are then later used to populate the remaining DSC
> > and RC parameters before enbaling DSC in atomic commit.
> > 
> > v9:
> > * Rebase on top of drm-tip that now uses fast_narrow config
> > for edp (Manasi)
> > v8:
> > * Check for DSC bpc not 0 (manasi)
> > 
> > v7:
> > * Fix indentation in compute_m_n (Manasi)
> > 
> > v6 (From Gaurav):
> > * Remove function call of intel_dp_compute_dsc_params() and
> > invoke intel_dp_compute_dsc_params() in the patch where
> > it is defined to fix compilation warning (Gaurav)
> > 
> > v5:
> > Add drm_dsc_cfg in intel_crtc_state (Manasi)
> > 
> > v4:
> > * Rebase on refactoring of intel_dp_compute_config on tip (Manasi)
> > * Add a comment why we need to check PSR while enabling DSC (Gaurav)
> > 
> > v3:
> > * Check PPR > max_cdclock to use 2 VDSC instances (Ville)
> > 
> > v2:
> > * Add if-else for eDP/DP (Gaurav)
> > 
> > Cc: Jani Nikula <jani.nikula at linux.intel.com>
> > Cc: Ville Syrjala <ville.syrjala at linux.intel.com>
> > Cc: Anusha Srivatsa <anusha.srivatsa at intel.com>
> > Cc: Gaurav K Singh <gaurav.k.singh at intel.com>
> > Signed-off-by: Manasi Navare <manasi.d.navare at intel.com>
> > Reviewed-by: Anusha Srivatsa <anusha.srivatsa at intel.com>
> > Acked-by: Jani Nikula <jani.nikula at linux.intel.com>
> > ---
> >  drivers/gpu/drm/i915/intel_display.c |  20 +++-
> >  drivers/gpu/drm/i915/intel_display.h |   3 +-
> >  drivers/gpu/drm/i915/intel_dp.c      | 170 ++++++++++++++++++++++-----
> >  drivers/gpu/drm/i915/intel_dp_mst.c  |   2 +-
> >  4 files changed, 155 insertions(+), 40 deletions(-)
> > 
> > diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c
> > index fe045abb6472..18737bd82b68 100644
> > --- a/drivers/gpu/drm/i915/intel_display.c
> > +++ b/drivers/gpu/drm/i915/intel_display.c
> > @@ -6434,7 +6434,7 @@ static int ironlake_fdi_compute_config(struct intel_crtc *intel_crtc,
> >  
> >  	pipe_config->fdi_lanes = lane;
> >  
> > -	intel_link_compute_m_n(pipe_config->pipe_bpp, lane, fdi_dotclock,
> > +	intel_link_compute_m_n(pipe_config->pipe_bpp, 0, lane, fdi_dotclock,
> >  			       link_bw, &pipe_config->fdi_m_n, false);
> >  
> >  	ret = ironlake_check_fdi_lanes(dev, intel_crtc->pipe, pipe_config);
> > @@ -6671,17 +6671,25 @@ static void compute_m_n(unsigned int m, unsigned int n,
> >  }
> >  
> >  void
> > -intel_link_compute_m_n(int bits_per_pixel, int nlanes,
> > +intel_link_compute_m_n(int bits_per_pixel, uint16_t compressed_bpp,
> > +		       int nlanes,
> >  		       int pixel_clock, int link_clock,
> >  		       struct intel_link_m_n *m_n,
> >  		       bool constant_n)
> >  {
> >  	m_n->tu = 64;
> >  
> > -	compute_m_n(bits_per_pixel * pixel_clock,
> > -		    link_clock * nlanes * 8,
> > -		    &m_n->gmch_m, &m_n->gmch_n,
> > -		    constant_n);
> > +	/* For DSC, Data M/N calculation uses compressed BPP */
> > +	if (compressed_bpp)
> > +		compute_m_n(compressed_bpp * pixel_clock,
> > +			    link_clock * nlanes * 8,
> > +			    &m_n->gmch_m, &m_n->gmch_n,
> > +			    constant_n);
> > +	else
> > +		compute_m_n(bits_per_pixel * pixel_clock,
> > +			    link_clock * nlanes * 8,
> > +			    &m_n->gmch_m, &m_n->gmch_n,
> > +			    constant_n);
> >  
> >  	compute_m_n(pixel_clock, link_clock,
> >  		    &m_n->link_m, &m_n->link_n,
> > diff --git a/drivers/gpu/drm/i915/intel_display.h b/drivers/gpu/drm/i915/intel_display.h
> > index 5d50decbcbb5..b0b23e1e9392 100644
> > --- a/drivers/gpu/drm/i915/intel_display.h
> > +++ b/drivers/gpu/drm/i915/intel_display.h
> > @@ -407,7 +407,8 @@ struct intel_link_m_n {
> >  	     (__i)++) \
> >  		for_each_if(plane)
> >  
> > -void intel_link_compute_m_n(int bpp, int nlanes,
> > +void intel_link_compute_m_n(int bpp, uint16_t compressed_bpp,
> > +			    int nlanes,
> >  			    int pixel_clock, int link_clock,
> >  			    struct intel_link_m_n *m_n,
> >  			    bool constant_n);
> > diff --git a/drivers/gpu/drm/i915/intel_dp.c b/drivers/gpu/drm/i915/intel_dp.c
> > index 6f66a38ba0b2..a88f9371dd32 100644
> > --- a/drivers/gpu/drm/i915/intel_dp.c
> > +++ b/drivers/gpu/drm/i915/intel_dp.c
> > @@ -47,6 +47,8 @@
> >  
> >  /* DP DSC small joiner has 2 FIFOs each of 640 x 6 bytes */
> >  #define DP_DSC_MAX_SMALL_JOINER_RAM_BUFFER	61440
> > +#define DP_DSC_MIN_SUPPORTED_BPC		8
> > +#define DP_DSC_MAX_SUPPORTED_BPC		10
> >  
> >  /* DP DSC throughput values used for slice count calculations KPixels/s */
> >  #define DP_DSC_PEAK_PIXEL_RATE			2720000
> > @@ -1924,6 +1926,16 @@ static int intel_dp_compute_bpp(struct intel_dp *intel_dp,
> >  		}
> >  	}
> >  
> > +	/* If DSC is supported, use the max value reported by panel */
> > +	if (INTEL_GEN(dev_priv) >= 10 &&
> > +	    drm_dp_sink_supports_dsc(intel_dp->dsc_dpcd)) {
> > +		bpc = min_t(u8,
> > +			    drm_dp_dsc_sink_max_color_depth(intel_dp->dsc_dpcd),
> > +			    DP_DSC_MAX_SUPPORTED_BPC);
> > +		if (bpc)
> > +			bpp = 3 * bpc;
> 
> This seems like it should be 'bpp = min(bpp, 3*bpc)'. 
> Otherwise we may bump the bpp above a limit we already established earlier.

Yes makes sense. Will change this.

Manasi

> 
> > +	}
> > +
> >  	return bpp;
> >  }
> >  
> > @@ -1984,14 +1996,11 @@ intel_dp_compute_link_config_wide(struct intel_dp *intel_dp,
> >  				link_clock = intel_dp->common_rates[clock];
> >  				link_avail = intel_dp_max_data_rate(link_clock,
> >  								    lane_count);
> > -
> > -				if (mode_rate <= link_avail) {
> > -					pipe_config->lane_count = lane_count;
> > -					pipe_config->pipe_bpp = bpp;
> > -					pipe_config->port_clock = link_clock;
> > -
> > +				pipe_config->lane_count = lane_count;
> > +				pipe_config->pipe_bpp = bpp;
> > +				pipe_config->port_clock = link_clock;
> > +				if (mode_rate <= link_avail)
> >  					return true;
> 
> Why do we need to assign these if we don't accept the configuration?
> 
> > -				}
> >  			}
> >  		}
> >  	}
> > @@ -2020,14 +2029,11 @@ intel_dp_compute_link_config_fast(struct intel_dp *intel_dp,
> >  				link_clock = intel_dp->common_rates[clock];
> >  				link_avail = intel_dp_max_data_rate(link_clock,
> >  								    lane_count);
> > -
> > -				if (mode_rate <= link_avail) {
> > -					pipe_config->lane_count = lane_count;
> > -					pipe_config->pipe_bpp = bpp;
> > -					pipe_config->port_clock = link_clock;
> > -
> > +				pipe_config->lane_count = lane_count;
> > +				pipe_config->pipe_bpp = bpp;
> > +				pipe_config->port_clock = link_clock;
> > +				if (mode_rate <= link_avail)
> >  					return true;
> > -				}
> >  			}
> >  		}
> >  	}
> > @@ -2035,14 +2041,88 @@ intel_dp_compute_link_config_fast(struct intel_dp *intel_dp,
> >  	return false;
> >  }
> >  
> > +static bool intel_dp_dsc_compute_config(struct intel_dp *intel_dp,
> > +					struct intel_crtc_state *pipe_config,
> > +					struct link_config_limits *limits)
> > +{
> > +	struct intel_digital_port *dig_port = dp_to_dig_port(intel_dp);
> > +	struct drm_i915_private *dev_priv = to_i915(dig_port->base.base.dev);
> > +	struct drm_display_mode *adjusted_mode = &pipe_config->base.adjusted_mode;
> > +	enum pipe pipe = to_intel_crtc(pipe_config->base.crtc)->pipe;
> > +	u16 dsc_max_output_bpp = 0;
> > +	u8 dsc_dp_slice_count = 0;
> > +
> > +	if (INTEL_GEN(dev_priv) < 10 ||
> > +	    !drm_dp_sink_supports_dsc(intel_dp->dsc_dpcd))
> > +		return false;
> > +
> > +	/* DP DSC only supported on Pipe B and C */
> > +	if (pipe == PIPE_A && !intel_dp_is_edp(intel_dp))
> > +		return false;
> 
> Do we mean 'transcoder == EDP || transcoder == B || transcoder == C' ?
> Or maybe 'transcoder != A' for short. I guess this will need to adjusted
> for the next platform anyway so making the assumption that transcoder A
> is the only one that can't do DSC is fine.
> 
> This whole thing seems like a good helper function.
> intel_dp_source_supports_dsc() or something like that. And then we
> could have intel_dp_supports_dsc() which just calls that +
> drm_dp_sink_supports_dsc().
> 
> intel_dp_compute_bpp() should use this at least, and probably a few
> other places as well.
> 
> > +
> > +	/* DSC not supported for DSC sink BPC < 8 */
> > +	if (limits->max_bpp < 3 * DP_DSC_MIN_SUPPORTED_BPC) {
> > +		DRM_DEBUG_KMS("No DSC support for less than 8bpc\n");
> > +		return false;
> > +	}
> > +
> > +	if (intel_dp_is_edp(intel_dp)) {
> > +		pipe_config->dsc_params.compressed_bpp =
> > +			drm_edp_dsc_sink_output_bpp(intel_dp->dsc_dpcd) >> 4;
> > +		pipe_config->dsc_params.slice_count =
> > +			drm_dp_dsc_sink_max_slice_count(intel_dp->dsc_dpcd,
> > +							true);
> > +	} else {
> > +		dsc_max_output_bpp =
> > +			intel_dp_dsc_get_output_bpp(pipe_config->port_clock,
> > +						    pipe_config->lane_count,
> > +						    adjusted_mode->crtc_clock,
> > +						    adjusted_mode->crtc_hdisplay);
> > +		dsc_dp_slice_count =
> > +			intel_dp_dsc_get_slice_count(intel_dp,
> > +						     adjusted_mode->crtc_clock,
> > +						     adjusted_mode->crtc_hdisplay);
> > +		if (!(dsc_max_output_bpp && dsc_dp_slice_count)) {
> > +			DRM_DEBUG_KMS("Compressed BPP/Slice Count not supported\n");
> > +			return false;
> > +		}
> > +		pipe_config->dsc_params.compressed_bpp = dsc_max_output_bpp >> 4;
> > +		pipe_config->dsc_params.slice_count = dsc_dp_slice_count;
> > +	}
> > +	/*
> > +	 * VDSC engine operates at 1 Pixel per clock, so if peak pixel rate
> > +	 * is greater than the maximum Cdclock and if slice count is even
> > +	 * then we need to use 2 VDSC instances.
> > +	 */
> > +	pipe_config->dsc_params.dsc_split = false;
> > +	if (adjusted_mode->crtc_clock > dev_priv->max_cdclk_freq) {
> > +		if (pipe_config->dsc_params.slice_count > 1) {
> > +			pipe_config->dsc_params.dsc_split = true;
> > +		} else {
> > +			DRM_DEBUG_KMS("Cannot split stream to use 2 VDSC instances\n");
> > +			return false;
> > +		}
> > +	}
> > +	pipe_config->dsc_params.compression_enable = true;
> > +	DRM_DEBUG_KMS("DP DSC computed with Input Bpp = %d "
> > +		      "Compressed Bpp = %d Slice Count = %d\n",
> > +		      pipe_config->pipe_bpp,
> > +		      pipe_config->dsc_params.compressed_bpp,
> > +		      pipe_config->dsc_params.slice_count);
> > +
> > +	return true;
> > +}
> > +
> >  static bool
> >  intel_dp_compute_link_config(struct intel_encoder *encoder,
> >  			     struct intel_crtc_state *pipe_config)
> >  {
> > +	struct drm_i915_private *dev_priv = to_i915(encoder->base.dev);
> >  	struct drm_display_mode *adjusted_mode = &pipe_config->base.adjusted_mode;
> >  	struct intel_dp *intel_dp = enc_to_intel_dp(&encoder->base);
> >  	struct link_config_limits limits;
> >  	int common_len;
> > +	bool ret = false;
> >  
> >  	common_len = intel_dp_common_len_rate_limit(intel_dp,
> >  						    intel_dp->max_link_rate);
> > @@ -2056,7 +2136,9 @@ intel_dp_compute_link_config(struct intel_encoder *encoder,
> >  	limits.min_lane_count = 1;
> >  	limits.max_lane_count = intel_dp_max_lane_count(intel_dp);
> >  
> > -	limits.min_bpp = 6 * 3;
> > +	limits.min_bpp = (INTEL_GEN(dev_priv) >= 10 &&
> > +			  drm_dp_sink_supports_dsc(intel_dp->dsc_dpcd)) ?
> > +		DP_DSC_MIN_SUPPORTED_BPC * 3 : 6 * 3;
> >  	limits.max_bpp = intel_dp_compute_bpp(intel_dp, pipe_config);
> 
> Hmm. This now assumes that we will in fact use DSC. I guess we can only
> make that assumption when we've determined that DSC is supported and the
> max_bpp also allows DSC.
> 
> So something like:
> 
> max_bpp = intel_dp_compute_bpp();
> if (supports_dsc() && max_bpp >= DP_DSC_MIN_SUPPORTED_BPC*3)
> 	min_bpp = DP_DSC_MIN_SUPPORTED_BPC * 3;
> else
> 	min_bpp = 6 * 3
> 
> >  
> >  	if (intel_dp_is_edp(intel_dp) && intel_dp->edp_dpcd[0] < DP_EDP_14) {
> > @@ -2081,7 +2163,7 @@ intel_dp_compute_link_config(struct intel_encoder *encoder,
> >  		      intel_dp->common_rates[limits.max_clock],
> >  		      limits.max_bpp, adjusted_mode->crtc_clock);
> >  
> > -	if (intel_dp_is_edp(intel_dp)) {
> > +	if (intel_dp_is_edp(intel_dp))
> >  		/*
> >  		 * Optimize for fast and narrow. eDP 1.3 section 3.3 and eDP 1.4
> >  		 * section A.1: "It is recommended that the minimum number of
> > @@ -2091,26 +2173,48 @@ intel_dp_compute_link_config(struct intel_encoder *encoder,
> >  		 * Note that we use the max clock and lane count for eDP 1.3 and
> >  		 * earlier, and fast vs. wide is irrelevant.
> >  		 */
> > -		if (!intel_dp_compute_link_config_fast(intel_dp, pipe_config,
> > -						       &limits))
> > -			return false;
> > -	} else {
> > +		ret = intel_dp_compute_link_config_fast(intel_dp, pipe_config,
> > +							&limits);
> > +	else
> >  		/* Optimize for slow and wide. */
> > -		if (!intel_dp_compute_link_config_wide(intel_dp, pipe_config,
> > -						       &limits))
> > +		ret = intel_dp_compute_link_config_wide(intel_dp, pipe_config,
> > +							&limits);
> > +
> > +	/* enable compression if the mode doesn't fit available BW */
> > +	if (!ret) {
> > +		DRM_DEBUG_KMS("DP required Link rate %i does not fit available %i\n",
> > +			      intel_dp_link_required(adjusted_mode->crtc_clock,
> > +						     pipe_config->pipe_bpp),
> > +			      intel_dp_max_data_rate(pipe_config->port_clock,
> > +						     pipe_config->lane_count));
> > +
> > +		if (!intel_dp_dsc_compute_config(intel_dp, pipe_config,
> > +						 &limits))
> >  			return false;
> >  	}
> >  
> > -	DRM_DEBUG_KMS("DP lane count %d clock %d bpp %d\n",
> > -		      pipe_config->lane_count, pipe_config->port_clock,
> > -		      pipe_config->pipe_bpp);
> > +	if (pipe_config->dsc_params.compression_enable) {
> > +		DRM_DEBUG_KMS("DP lane count %d clock %d Input bpp %d Compressed bpp %d\n",
> > +			      pipe_config->lane_count, pipe_config->port_clock,
> > +			      pipe_config->pipe_bpp,
> > +			      pipe_config->dsc_params.compressed_bpp);
> >  
> > -	DRM_DEBUG_KMS("DP link rate required %i available %i\n",
> > -		      intel_dp_link_required(adjusted_mode->crtc_clock,
> > -					     pipe_config->pipe_bpp),
> > -		      intel_dp_max_data_rate(pipe_config->port_clock,
> > -					     pipe_config->lane_count));
> > +		DRM_DEBUG_KMS("DP link rate required %i available %i\n",
> > +			      intel_dp_link_required(adjusted_mode->crtc_clock,
> > +						     pipe_config->dsc_params.compressed_bpp),
> > +			      intel_dp_max_data_rate(pipe_config->port_clock,
> > +						     pipe_config->lane_count));
> > +	} else {
> > +		DRM_DEBUG_KMS("DP lane count %d clock %d bpp %d\n",
> > +			      pipe_config->lane_count, pipe_config->port_clock,
> > +			      pipe_config->pipe_bpp);
> >  
> > +		DRM_DEBUG_KMS("DP link rate required %i available %i\n",
> > +			      intel_dp_link_required(adjusted_mode->crtc_clock,
> > +						     pipe_config->pipe_bpp),
> > +			      intel_dp_max_data_rate(pipe_config->port_clock,
> > +						     pipe_config->lane_count));
> > +	}
> >  	return true;
> >  }
> >  
> > @@ -2194,7 +2298,9 @@ intel_dp_compute_config(struct intel_encoder *encoder,
> >  			intel_conn_state->broadcast_rgb == INTEL_BROADCAST_RGB_LIMITED;
> >  	}
> >  
> > -	intel_link_compute_m_n(pipe_config->pipe_bpp, pipe_config->lane_count,
> > +	intel_link_compute_m_n(pipe_config->pipe_bpp,
> > +			       pipe_config->dsc_params.compressed_bpp,
> > +			       pipe_config->lane_count,
> >  			       adjusted_mode->crtc_clock,
> >  			       pipe_config->port_clock,
> >  			       &pipe_config->dp_m_n,
> > @@ -2203,7 +2309,7 @@ intel_dp_compute_config(struct intel_encoder *encoder,
> >  	if (intel_connector->panel.downclock_mode != NULL &&
> >  		dev_priv->drrs.type == SEAMLESS_DRRS_SUPPORT) {
> >  			pipe_config->has_drrs = true;
> > -			intel_link_compute_m_n(pipe_config->pipe_bpp,
> > +			intel_link_compute_m_n(pipe_config->pipe_bpp, 0,
> >  					       pipe_config->lane_count,
> >  					       intel_connector->panel.downclock_mode->clock,
> >  					       pipe_config->port_clock,
> > diff --git a/drivers/gpu/drm/i915/intel_dp_mst.c b/drivers/gpu/drm/i915/intel_dp_mst.c
> > index 8b71d64ebd9d..e02caedd443c 100644
> > --- a/drivers/gpu/drm/i915/intel_dp_mst.c
> > +++ b/drivers/gpu/drm/i915/intel_dp_mst.c
> > @@ -90,7 +90,7 @@ static bool intel_dp_mst_compute_config(struct intel_encoder *encoder,
> >  		}
> >  	}
> >  
> > -	intel_link_compute_m_n(bpp, lane_count,
> > +	intel_link_compute_m_n(bpp, 0, lane_count,
> >  			       adjusted_mode->crtc_clock,
> >  			       pipe_config->port_clock,
> >  			       &pipe_config->dp_m_n,
> > -- 
> > 2.18.0
> 
> -- 
> Ville Syrjälä
> Intel


More information about the Intel-gfx mailing list