[Intel-gfx] [PATCH 3/7] drm/i915/tgl: Select master trasconder for MST stream
Souza, Jose
jose.souza at intel.com
Mon Dec 2 22:03:38 UTC 2019
On Thu, 2019-11-28 at 14:06 +0200, Ville Syrjälä wrote:
> On Thu, Nov 28, 2019 at 01:14:37AM +0000, Souza, Jose wrote:
> > On Wed, 2019-11-27 at 21:59 +0200, Ville Syrjälä wrote:
> > > On Tue, Nov 26, 2019 at 08:30:31PM +0000, Souza, Jose wrote:
> > > > On Tue, 2019-11-26 at 22:05 +0200, Ville Syrjälä wrote:
> > > > > On Fri, Nov 22, 2019 at 04:54:55PM -0800, José Roberto de
> > > > > Souza
> > > > > wrote:
> > > > > > On TGL the blending of all the streams have moved from DDI
> > > > > > to
> > > > > > transcoder, so now every transcoder working over the same
> > > > > > MST
> > > > > > port
> > > > > > must
> > > > > > send its stream to a master transcoder and master will send
> > > > > > to
> > > > > > DDI
> > > > > > respecting the time slots.
> > > > > >
> > > > > > A previous approach was using the lowest pipe/transcoder as
> > > > > > master
> > > > > > transcoder but as the comment in
> > > > > > skl_commit_modeset_enables()
> > > > > > states,
> > > > > > that is not always true.
> > > > > >
> > > > > > So here promoting the first pipe/transcoder of the stream
> > > > > > as
> > > > > > master.
> > > > > > That caused several other problems as during the commit
> > > > > > phase
> > > > > > the
> > > > > > state computed should not be changed.
> > > > > >
> > > > > > So the master transcoder is store into intel_dp and the
> > > > > > modeset
> > > > > > in
> > > > > > slave pipes/transcoders is forced using
> > > > > > mst_master_trans_pending.
> > > > > >
> > > > > > v2:
> > > > > > - added missing config compute to trigger fullmodeset in
> > > > > > slave
> > > > > > transcoders
> > > > > >
> > > > > > BSpec: 50493
> > > > > > BSpec: 49190
> > > > > > Cc: Ville Syrjälä <ville.syrjala at linux.intel.com>
> > > > > > Cc: Lucas De Marchi <lucas.demarchi at intel.com>
> > > > > > Signed-off-by: José Roberto de Souza <jose.souza at intel.com>
> > > > > > ---
> > > > > > drivers/gpu/drm/i915/display/intel_ddi.c | 10 +-
> > > > > > drivers/gpu/drm/i915/display/intel_display.c | 58
> > > > > > ++++++-
> > > > > > .../drm/i915/display/intel_display_types.h | 3 +
> > > > > > drivers/gpu/drm/i915/display/intel_dp.c | 1 +
> > > > > > drivers/gpu/drm/i915/display/intel_dp_mst.c | 149
> > > > > > +++++++++++++++++-
> > > > > > drivers/gpu/drm/i915/display/intel_dp_mst.h | 2 +
> > > > > > 6 files changed, 216 insertions(+), 7 deletions(-)
> > > > > >
> > > > > > diff --git a/drivers/gpu/drm/i915/display/intel_ddi.c
> > > > > > b/drivers/gpu/drm/i915/display/intel_ddi.c
> > > > > > index a976606d21c7..d2f0d393d3ee 100644
> > > > > > --- a/drivers/gpu/drm/i915/display/intel_ddi.c
> > > > > > +++ b/drivers/gpu/drm/i915/display/intel_ddi.c
> > > > > > @@ -35,6 +35,7 @@
> > > > > > #include "intel_display_types.h"
> > > > > > #include "intel_dp.h"
> > > > > > #include "intel_dp_link_training.h"
> > > > > > +#include "intel_dp_mst.h"
> > > > > > #include "intel_dpio_phy.h"
> > > > > > #include "intel_dsi.h"
> > > > > > #include "intel_fifo_underrun.h"
> > > > > > @@ -1903,8 +1904,13 @@
> > > > > > intel_ddi_transcoder_func_reg_val_get(const
> > > > > > struct intel_crtc_state *crtc_state)
> > > > > > temp |= TRANS_DDI_MODE_SELECT_DP_MST;
> > > > > > temp |= DDI_PORT_WIDTH(crtc_state->lane_count);
> > > > > >
> > > > > > - if (INTEL_GEN(dev_priv) >= 12)
> > > > > > - temp |=
> > > > > > TRANS_DDI_MST_TRANSPORT_SELECT(crtc_state->cpu_transcoder);
> > > > > > + if (INTEL_GEN(dev_priv) >= 12) {
> > > > > > + enum transcoder master;
> > > > > > +
> > > > > > + master =
> > > > > > intel_dp_mst_master_trans_get(encoder);
> > > > >
> > > > > Why isn't that just stored in the crtc state like everything
> > > > > else?
> > > > >
> > > > > I'm thinking we should maybe do it just like port sync and
> > > > > have
> > > > > both
> > > > > master + slave_mask. That way it should be pretty trivial to
> > > > > add
> > > > > all
> > > > > the relevant crtcs to the state when needed.
> > > >
> > > > I guess port sync is not doing the right thing and it could
> > > > cause
> > > > underruns.
> > > > When it is going to enable the master CRTC of the port sync it
> > > > forcibly
> > > > enables the slave first, what could cause underruns because of
> > > > overlap
> > > > in ddb allocations(that is what I understood from the comment
> > > > in
> > > > skl_commit_modeset_enables()).
> > >
> > > Not necessarily just underruns but even a system hang. The fix
> > > should
> > > be
> > > a trivial "check the slave for ddb overlap as well", but
> > > apparently I
> > > failed at convicing people to do that.
> > >
> > > I've actually been pondering about decoupling the plane updates
> > > from
> > > the crtc enable stuff entirely. At least theoretically crtc
> > > enable
> > > should be able to excute in any order as long we don't enable any
> > > new planes.
> > >
> > > But none of that really matters for the discussion at hand.
> > > Though
> > > there are other problems with the port sync stuff that would need
> > > to be handled better. Eg. I think it now adds both crtcs to the
> > > state
> > > always which is going to cut the fps in half. Also the place
> > > where
> > > it does that stuff is rather suspicious. All that stuff should be
> > > somewhere a bit higher up IMO.
> > >
> > > > So for MST we only know who is the master in the commit phase
> > > > and
> > > > at
> > > > this point we should not modify the computed state.
> > >
> > > I'm not suggesting modifying anything during commit phase. I
> > > think
> > > you are effectiely doing that right now by stuffing that mst
> > > master
> > > transcoder into intel_dp.
> >
> > Sorry, I still don't get what approach are you suggesting here.
> >
> > If we can't modify the state in the commit phase, adding
> > mst_master_transcoder in the CRTC state will not be possible while
> > respecting the order imposed by ddb allocations.
>
> The ddb allocation ordering only comes into play when there are
> already active pipes. It should always be possible to not enable
> the slaves until the master has been shuffled into place in the
> ddb and enabled.
This sounds contradictory to what you answered here:
https://lists.freedesktop.org/archives/intel-gfx/2019-November/221608.html
Will need to some testing to get the steps but I was able consistent to
get to state were doing a full modeset in pipe A(mst master) caused the
pipe B(mst slave) to enabled first because of the ddb allocations.
So can I or not do something like port sync does? And force the enable
of master before the slaves? If possible, the comment in
skl_commit_modeset_enables() will need some changes.
>
> > > > > > + WARN_ON(master == INVALID_TRANSCODER);
> > > > > > + temp |=
> > > > > > TRANS_DDI_MST_TRANSPORT_SELECT(master);
> > > > > > + }
> > > > > > } else {
> > > > > > temp |= TRANS_DDI_MODE_SELECT_DP_SST;
> > > > > > temp |= DDI_PORT_WIDTH(crtc_state->lane_count);
> > > > > > diff --git a/drivers/gpu/drm/i915/display/intel_display.c
> > > > > > b/drivers/gpu/drm/i915/display/intel_display.c
> > > > > > index 801b975c7d39..35a59108194e 100644
> > > > > > --- a/drivers/gpu/drm/i915/display/intel_display.c
> > > > > > +++ b/drivers/gpu/drm/i915/display/intel_display.c
> > > > > > @@ -46,6 +46,7 @@
> > > > > > #include "display/intel_crt.h"
> > > > > > #include "display/intel_ddi.h"
> > > > > > #include "display/intel_dp.h"
> > > > > > +#include "display/intel_dp_mst.h"
> > > > > > #include "display/intel_dsi.h"
> > > > > > #include "display/intel_dvo.h"
> > > > > > #include "display/intel_gmbus.h"
> > > > > > @@ -5365,6 +5366,36 @@ intel_get_crtc_new_encoder(const
> > > > > > struct
> > > > > > intel_atomic_state *state,
> > > > > > return encoder;
> > > > > > }
> > > > > >
> > > > > > +/*
> > > > > > + * Finds the encoder associated with the given CRTC. This
> > > > > > can
> > > > > > only
> > > > > > be
> > > > > > + * used when we know that the CRTC isn't feeding multiple
> > > > > > encoders!
> > > > > > + */
> > > > > > +static struct intel_encoder *
> > > > > > +intel_get_crtc_old_encoder(const struct intel_atomic_state
> > > > > > *state,
> > > > > > + const struct intel_crtc_state
> > > > > > *crtc_state)
> > > > > > +{
> > > > > > + struct intel_crtc *crtc = to_intel_crtc(crtc_state-
> > > > > > > uapi.crtc);
> > > > > > + const struct drm_connector_state *connector_state;
> > > > > > + const struct drm_connector *connector;
> > > > > > + struct intel_encoder *encoder = NULL;
> > > > > > + int num_encoders = 0;
> > > > > > + int i;
> > > > > > +
> > > > > > + for_each_old_connector_in_state(&state->base,
> > > > > > connector,
> > > > > > + connector_state, i) {
> > > > > > + if (connector_state->crtc != &crtc->base)
> > > > > > + continue;
> > > > > > +
> > > > > > + encoder = to_intel_encoder(connector_state-
> > > > > > > best_encoder);
> > > > > > + num_encoders++;
> > > > > > + }
> > > > > > +
> > > > > > + WARN(num_encoders != 1, "%d encoders for pipe %c\n",
> > > > > > + num_encoders, pipe_name(crtc->pipe));
> > > > > > +
> > > > > > + return encoder;
> > > > > > +}
> > > > >
> > > > > Argh. I was hoping to kill the other one of these. Got it
> > > > > down to
> > > > > 1
> > > > > remaining user now I think.
> > > > >
> > > > > > +
> > > > > > /*
> > > > > > * Enable PCH resources required for PCH ports:
> > > > > > * - PCH PLLs
> > > > > > @@ -13365,6 +13396,12 @@ intel_pipe_config_compare(const
> > > > > > struct
> > > > > > intel_crtc_state *current_config,
> > > > > > #undef PIPE_CONF_CHECK_COLOR_LUT
> > > > > > #undef PIPE_CONF_QUIRK
> > > > > >
> > > > > > + if (fastset && pipe_config->mst_master_trans_pending) {
> > > > > > + DRM_DEBUG_KMS("[CRTC:%d:%s] fastset mismatch in
> > > > > > mst_master_trans\n",
> > > > > > + crtc->base.base.id, crtc-
> > > > > > > base.name);
> > > > > > + ret = false;
> > > > > > + }
> > > > > > +
> > > > > > return ret;
> > > > > > }
> > > > > >
> > > > > > @@ -14449,22 +14486,35 @@ static void
> > > > > > intel_commit_modeset_disables(struct intel_atomic_state
> > > > > > *state)
> > > > > > struct intel_crtc *crtc;
> > > > > > int i;
> > > > > >
> > > > > > - /* Only disable port sync slaves */
> > > > > > + /* Only disable port sync and MST slaves */
> > > > > > for_each_oldnew_intel_crtc_in_state(state, crtc,
> > > > > > old_crtc_state,
> > > > > > new_crtc_state, i)
> > > > > > {
> > > > > > if (!needs_modeset(new_crtc_state) || !crtc-
> > > > > > > active)
> > > > > > continue;
> > > > > >
> > > > > > + if (!is_trans_port_sync_mode(new_crtc_state) &&
> > > > > > + !intel_crtc_has_type(old_crtc_state,
> > > > > > INTEL_OUTPUT_DP_MST))
> > > > > > + continue;
> > > > > > +
> > > > > > /* In case of Transcoder port Sync master slave
> > > > > > CRTCs
> > > > > > can be
> > > > > > * assigned in any order and we need to make
> > > > > > sure that
> > > > > > * slave CRTCs are disabled first and then
> > > > > > master CRTC
> > > > > > since
> > > > > > * Slave vblanks are masked till Master
> > > > > > Vblanks.
> > > > > > */
> > > > > > - if (!is_trans_port_sync_mode(old_crtc_state))
> > > > > > - continue;
> > > > > > - if (is_trans_port_sync_master(old_crtc_state))
> > > > > > + if (is_trans_port_sync_mode(new_crtc_state) &&
> > > > > > + is_trans_port_sync_master(new_crtc_state))
> > > > > > continue;
> > > > > >
> > > > > > + if (intel_crtc_has_type(old_crtc_state,
> > > > > > INTEL_OUTPUT_DP_MST)) {
> > > > > > + struct intel_encoder *encoder;
> > > > > > +
> > > > > > + encoder =
> > > > > > intel_get_crtc_old_encoder(state,
> > > > > > + ol
> > > > > > d_crtc_s
> > > > > > tate);
> > > > > > + if
> > > > > > (intel_dp_mst_master_trans_get(encoder) ==
> > > > > > + old_crtc_state->cpu_transcoder)
> > > > > > + continue;
> > > > > > + }
> > > > > > +
> > > > > > intel_pre_plane_update(old_crtc_state,
> > > > > > new_crtc_state);
> > > > > > intel_old_crtc_state_disables(state,
> > > > > > old_crtc_state,
> > > > > > new_crtc_state,
> > > > > > crtc);
> > > > > > diff --git
> > > > > > a/drivers/gpu/drm/i915/display/intel_display_types.h
> > > > > > b/drivers/gpu/drm/i915/display/intel_display_types.h
> > > > > > index 83ea04149b77..23d747cdca64 100644
> > > > > > --- a/drivers/gpu/drm/i915/display/intel_display_types.h
> > > > > > +++ b/drivers/gpu/drm/i915/display/intel_display_types.h
> > > > > > @@ -1052,6 +1052,8 @@ struct intel_crtc_state {
> > > > > > /* Pointer to master transcoder in case of tiled
> > > > > > displays */
> > > > > > enum transcoder master_transcoder;
> > > > > >
> > > > > > + bool mst_master_trans_pending;
> > > > > > +
> > > > > > /* Bitmask to indicate slaves attached */
> > > > > > u8 sync_mode_slaves_mask;
> > > > > > };
> > > > > > @@ -1284,6 +1286,7 @@ struct intel_dp {
> > > > > > bool can_mst; /* this port supports mst */
> > > > > > bool is_mst;
> > > > > > int active_mst_links;
> > > > > > + enum transcoder mst_master_transcoder; /* Only used in
> > > > > > TGL+ */
> > > > > >
> > > > > > /*
> > > > > > * DP_TP_* registers may be either on port or
> > > > > > transcoder
> > > > > > register space.
> > > > > > diff --git a/drivers/gpu/drm/i915/display/intel_dp.c
> > > > > > b/drivers/gpu/drm/i915/display/intel_dp.c
> > > > > > index 3123958e2081..ceff6901451a 100644
> > > > > > --- a/drivers/gpu/drm/i915/display/intel_dp.c
> > > > > > +++ b/drivers/gpu/drm/i915/display/intel_dp.c
> > > > > > @@ -7424,6 +7424,7 @@ intel_dp_init_connector(struct
> > > > > > intel_digital_port *intel_dig_port,
> > > > > > intel_dp->reset_link_params = true;
> > > > > > intel_dp->pps_pipe = INVALID_PIPE;
> > > > > > intel_dp->active_pipe = INVALID_PIPE;
> > > > > > + intel_dp->mst_master_transcoder = INVALID_TRANSCODER;
> > > > > >
> > > > > > /* Preserve the current hw state. */
> > > > > > intel_dp->DP = I915_READ(intel_dp->output_reg);
> > > > > > diff --git a/drivers/gpu/drm/i915/display/intel_dp_mst.c
> > > > > > b/drivers/gpu/drm/i915/display/intel_dp_mst.c
> > > > > > index f8a350359346..9731c3c1d3f2 100644
> > > > > > --- a/drivers/gpu/drm/i915/display/intel_dp_mst.c
> > > > > > +++ b/drivers/gpu/drm/i915/display/intel_dp_mst.c
> > > > > > @@ -87,6 +87,47 @@ static int
> > > > > > intel_dp_mst_compute_link_config(struct intel_encoder
> > > > > > *encoder,
> > > > > > return 0;
> > > > > > }
> > > > > >
> > > > > > +static int
> > > > > > +intel_dp_mst_master_trans_compute(struct intel_encoder
> > > > > > *encoder,
> > > > > > + struct intel_crtc_state
> > > > > > *pipe_config,
> > > > > > + struct drm_connector_state
> > > > > > *conn_state)
> > > > > > +{
> > > > > > + struct intel_atomic_state *state =
> > > > > > to_intel_atomic_state(pipe_config->uapi.state);
> > > > > > + struct drm_i915_private *dev_priv = to_i915(encoder-
> > > > > > > base.dev);
> > > > > > + struct intel_crtc_state *new_crtc_state;
> > > > > > + struct intel_crtc *crtc;
> > > > > > + enum transcoder master;
> > > > > > + int i;
> > > > > > +
> > > > > > + if (INTEL_GEN(dev_priv) < 12)
> > > > > > + return 0;
> > > > > > +
> > > > > > + if (!conn_state->crtc)
> > > > > > + return 0;
> > > > > > +
> > > > > > + master = intel_dp_mst_master_trans_get(encoder);
> > > > > > + if (master == INVALID_TRANSCODER)
> > > > > > + return 0;
> > > > > > +
> > > > > > + for_each_new_intel_crtc_in_state(state, crtc,
> > > > > > new_crtc_state,
> > > > > > i) {
> > > > > > + /*
> > > > > > + * cpu_transcoder is set when computing CRTC
> > > > > > state if
> > > > > > it will
> > > > > > + * be disabled it will not happen, so checking
> > > > > > pipe
> > > > > > instead
> > > > > > + */
> > > > > > + if (crtc->pipe != (enum pipe)master)
> > > > > > + continue;
> > > > > > +
> > > > > > + if
> > > > > > (!drm_atomic_crtc_needs_modeset(&new_crtc_state-
> > > > > > > uapi) &&
> > > > > > + new_crtc_state->uapi.enable)
> > > > > > + continue;
> > > > > > +
> > > > > > + pipe_config->mst_master_trans_pending = true;
> > > > > > + break;
> > > > > > + }
> > > > > > +
> > > > > > + return 0;
> > > > > > +}
> > > > > > +
> > > > > > static int intel_dp_mst_compute_config(struct
> > > > > > intel_encoder
> > > > > > *encoder,
> > > > > > struct intel_crtc_state
> > > > > > *pipe_config,
> > > > > > struct
> > > > > > drm_connector_state
> > > > > > *conn_state)
> > > > > > @@ -154,6 +195,95 @@ static int
> > > > > > intel_dp_mst_compute_config(struct
> > > > > > intel_encoder *encoder,
> > > > > >
> > > > > > intel_ddi_compute_min_voltage_level(dev_priv,
> > > > > > pipe_config);
> > > > > >
> > > > > > + ret = intel_dp_mst_master_trans_compute(encoder,
> > > > > > pipe_config,
> > > > > > + conn_state);
> > > > > > + if (ret)
> > > > > > + return ret;
> > > > > > +
> > > > > > + return 0;
> > > > > > +}
> > > > > > +
> > > > > > +static int
> > > > > > +intel_dp_mst_atomic_master_trans_check(struct
> > > > > > drm_connector
> > > > > > *connector,
> > > > > > + struct drm_atomic_state
> > > > > > *state)
> > > > > > +{
> > > > > > + struct drm_i915_private *dev_priv = to_i915(connector-
> > > > > > > dev);
> > > > > > + struct intel_connector *intel_conn =
> > > > > > to_intel_connector(connector);
> > > > > > + struct drm_connector_state *new_conn_state,
> > > > > > *old_conn_state;
> > > > > > + struct drm_connector_list_iter conn_list_iter;
> > > > > > + struct intel_crtc_state *intel_crtc_state;
> > > > > > + struct drm_crtc_state *crtc_state;
> > > > > > + struct drm_connector *conn_iter;
> > > > > > +
> > > > > > + if (INTEL_GEN(dev_priv) < 12)
> > > > > > + return 0;
> > > > > > +
> > > > > > + new_conn_state =
> > > > > > drm_atomic_get_new_connector_state(state,
> > > > > > connector);
> > > > > > + old_conn_state =
> > > > > > drm_atomic_get_old_connector_state(state,
> > > > > > connector);
> > > > > > +
> > > > > > + if (!old_conn_state->crtc && !new_conn_state->crtc)
> > > > > > + return 0;
> > > > > > +
> > > > > > + /*
> > > > > > + * 3 cases that needs be handled here:
> > > > > > + * - connector going from disabled to enabled
> > > > > > + * - connector going from enabled to disabled:
> > > > > > + * if this transcoder was the master, all slaves needs
> > > > > > a
> > > > > > modeset
> > > > > > + * - connector going from enabled to enabled but it
> > > > > > needs a
> > > > > > modeset:
> > > > > > + * if this transcoder was the master, all slaves also
> > > > > > needs a
> > > > > > modeset
> > > > > > + */
> > > > > > +
> > > > > > + /* disabled -> enabled */
> > > > > > + if (!old_conn_state->crtc && new_conn_state->crtc)
> > > > > > + return 0;
> > > > > > +
> > > > > > + /* enabled -> enabled(modeset)? */
> > > > > > + if (new_conn_state->crtc) {
> > > > > > + crtc_state =
> > > > > > drm_atomic_get_new_crtc_state(state,
> > > > > > new_conn_state->crtc);
> > > > > > + if (!drm_atomic_crtc_needs_modeset(crtc_state))
> > > > > > + return 0;
> > > > > > + }
> > > > > > +
> > > > > > + /* handling enabled -> enabled(modeset) and enabled ->
> > > > > > disabled
> > > > > > */
> > > > > > + crtc_state = drm_atomic_get_old_crtc_state(state,
> > > > > > old_conn_state->crtc);
> > > > > > + intel_crtc_state = to_intel_crtc_state(crtc_state);
> > > > > > +
> > > > > > + /* If not master, nothing else needs to be handled */
> > > > > > + if (intel_conn->mst_port->mst_master_transcoder !=
> > > > > > + intel_crtc_state->cpu_transcoder)
> > > > > > + return 0;
> > > > > > +
> > > > > > + /* Is master, mark all other CRTCs as needing a modeset
> > > > > > */
> > > > > > + drm_connector_list_iter_begin(state->dev,
> > > > > > &conn_list_iter);
> > > > > > + drm_for_each_connector_iter(conn_iter, &conn_list_iter)
> > > > > > {
> > > > > > + struct intel_connector *intel_conn_iter;
> > > > > > + struct drm_connector_state *conn_iter_state;
> > > > > > +
> > > > > > + intel_conn_iter =
> > > > > > to_intel_connector(conn_iter);
> > > > > > + if (intel_conn_iter->mst_port != intel_conn-
> > > > > > > mst_port)
> > > > > > + continue;
> > > > > > +
> > > > > > + conn_iter_state =
> > > > > > drm_atomic_get_connector_state(state,
> > > > > > +
> > > > > > conn_i
> > > > > > ter);
> > > > > > + if (IS_ERR(conn_iter_state)) {
> > > > > > + drm_connector_list_iter_end(&conn_list_
> > > > > > iter);
> > > > > > + return PTR_ERR(conn_iter_state);
> > > > > > + }
> > > > > > +
> > > > > > + if (!conn_iter_state->crtc)
> > > > > > + continue;
> > > > > > +
> > > > > > + crtc_state = drm_atomic_get_crtc_state(state,
> > > > > > conn_iter_state->crtc);
> > > > > > + if (IS_ERR(crtc_state)) {
> > > > > > + drm_connector_list_iter_end(&conn_list_
> > > > > > iter);
> > > > > > + return PTR_ERR(conn_iter_state);
> > > > > > + }
> > > > > > +
> > > > > > + intel_crtc_state =
> > > > > > to_intel_crtc_state(crtc_state);
> > > > > > + crtc_state->mode_changed = true;
> > > > > > + }
> > > > > > + drm_connector_list_iter_end(&conn_list_iter);
> > > > > > +
> > > > > > return 0;
> > > > > > }
> > > > > >
> > > > > > @@ -175,6 +305,10 @@ intel_dp_mst_atomic_check(struct
> > > > > > drm_connector
> > > > > > *connector,
> > > > > > if (ret)
> > > > > > return ret;
> > > > > >
> > > > > > + ret = intel_dp_mst_atomic_master_trans_check(connector,
> > > > > > state);
> > > > > > + if (ret)
> > > > > > + return ret;
> > > > > > +
> > > > > > if (!old_conn_state->crtc)
> > > > > > return 0;
> > > > > >
> > > > > > @@ -259,6 +393,7 @@ static void
> > > > > > intel_mst_post_disable_dp(struct
> > > > > > intel_encoder *encoder,
> > > > > > intel_dp_sink_dpms(intel_dp,
> > > > > > DRM_MODE_DPMS_OFF);
> > > > > > intel_dig_port-
> > > > > > > base.post_disable(&intel_dig_port-
> > > > > > > base,
> > > > > > old_crtc_stat
> > > > > > e,
> > > > > > NULL);
> > > > > > + intel_dp->mst_master_transcoder =
> > > > > > INVALID_TRANSCODER;
> > > > > > }
> > > > > >
> > > > > > DRM_DEBUG_KMS("active links %d\n", intel_dp-
> > > > > > > active_mst_links);
> > > > > > @@ -314,8 +449,11 @@ static void
> > > > > > intel_mst_pre_enable_dp(struct
> > > > > > intel_encoder *encoder,
> > > > > >
> > > > > > DRM_DEBUG_KMS("active links %d\n", intel_dp-
> > > > > > > active_mst_links);
> > > > > >
> > > > > > - if (first_mst_stream)
> > > > > > + if (first_mst_stream) {
> > > > > > + WARN_ON(intel_dp->mst_master_transcoder !=
> > > > > > INVALID_TRANSCODER);
> > > > > > + intel_dp->mst_master_transcoder = pipe_config-
> > > > > > > cpu_transcoder;
> > > > > > intel_dp_sink_dpms(intel_dp, DRM_MODE_DPMS_ON);
> > > > > > + }
> > > > > >
> > > > > > drm_dp_send_power_updown_phy(&intel_dp->mst_mgr,
> > > > > > connector-
> > > > > > > port, true);
> > > > > >
> > > > > > @@ -717,3 +855,12 @@ intel_dp_mst_encoder_cleanup(struct
> > > > > > intel_digital_port *intel_dig_port)
> > > > > > drm_dp_mst_topology_mgr_destroy(&intel_dp->mst_mgr);
> > > > > > /* encoders will get killed by normal cleanup */
> > > > > > }
> > > > > > +
> > > > > > +enum transcoder
> > > > > > +intel_dp_mst_master_trans_get(struct intel_encoder
> > > > > > *encoder)
> > > > > > +{
> > > > > > + struct intel_dp_mst_encoder *intel_mst =
> > > > > > enc_to_mst(&encoder-
> > > > > > > base);
> > > > > > + struct intel_dp *intel_dp = &intel_mst->primary->dp;
> > > > > > +
> > > > > > + return intel_dp->mst_master_transcoder;
> > > > > > +}
> > > > > > diff --git a/drivers/gpu/drm/i915/display/intel_dp_mst.h
> > > > > > b/drivers/gpu/drm/i915/display/intel_dp_mst.h
> > > > > > index f660ad80db04..e6f28a517182 100644
> > > > > > --- a/drivers/gpu/drm/i915/display/intel_dp_mst.h
> > > > > > +++ b/drivers/gpu/drm/i915/display/intel_dp_mst.h
> > > > > > @@ -7,9 +7,11 @@
> > > > > > #define __INTEL_DP_MST_H__
> > > > > >
> > > > > > struct intel_digital_port;
> > > > > > +struct intel_encoder;
> > > > > >
> > > > > > int intel_dp_mst_encoder_init(struct intel_digital_port
> > > > > > *intel_dig_port, int conn_id);
> > > > > > void intel_dp_mst_encoder_cleanup(struct
> > > > > > intel_digital_port
> > > > > > *intel_dig_port);
> > > > > > int intel_dp_mst_encoder_active_links(struct
> > > > > > intel_digital_port
> > > > > > *intel_dig_port);
> > > > > > +enum transcoder intel_dp_mst_master_trans_get(struct
> > > > > > intel_encoder
> > > > > > *encoder);
> > > > > >
> > > > > > #endif /* __INTEL_DP_MST_H__ */
> > > > > > --
> > > > > > 2.24.0
More information about the Intel-gfx
mailing list