[Intel-gfx] [PATCH 6/7] drm/i915/display/tgl: Fix the order of the step to turn transcoder clock off
Ville Syrjälä
ville.syrjala at linux.intel.com
Wed Dec 4 10:56:37 UTC 2019
On Tue, Dec 03, 2019 at 11:29:49PM +0000, Souza, Jose wrote:
> On Thu, 2019-11-28 at 20:40 +0200, Ville Syrjälä wrote:
> > On Fri, Nov 22, 2019 at 04:54:58PM -0800, José Roberto de Souza
> > wrote:
> > > For TGL the step to turn off the transcoder clock was moved to
> > > after
> > > the complete shutdown of DDI. Only the MST slave transcoders should
> > > disable the clock before that.
> > >
> > > BSpec: 49190
> > > Signed-off-by: José Roberto de Souza <jose.souza at intel.com>
> > > ---
> > > drivers/gpu/drm/i915/display/intel_ddi.c | 9 ++++++++-
> > > drivers/gpu/drm/i915/display/intel_dp_mst.c | 15 ++++++++++++---
> > > 2 files changed, 20 insertions(+), 4 deletions(-)
> > >
> > > diff --git a/drivers/gpu/drm/i915/display/intel_ddi.c
> > > b/drivers/gpu/drm/i915/display/intel_ddi.c
> > > index cfcaa7c81575..aa0249333175 100644
> > > --- a/drivers/gpu/drm/i915/display/intel_ddi.c
> > > +++ b/drivers/gpu/drm/i915/display/intel_ddi.c
> > > @@ -3813,7 +3813,7 @@ static void intel_ddi_post_disable_dp(struct
> > > intel_encoder *encoder,
> > > */
> > > intel_dp_sink_dpms(intel_dp, DRM_MODE_DPMS_OFF);
> > >
> > > - if (!is_mst)
> > > + if (INTEL_GEN(dev_priv) < 12 && !is_mst)
> > > intel_ddi_disable_pipe_clock(old_crtc_state);
> > >
> > > intel_disable_ddi_buf(encoder, old_crtc_state);
> > > @@ -3826,6 +3826,13 @@ static void intel_ddi_post_disable_dp(struct
> > > intel_encoder *encoder,
> > > intel_display_power_put_unchecked(dev_priv,
> > > dig_port-
> > > >ddi_io_power_domain);
> > >
> > > + /*
> > > + * From TGL BSpec "If single stream or multi-stream master
> > > transcoder:
> > > + * Configure Transcoder Clock select to direct no clock to the
> > > + * transcoder"
> > > + */
> >
> > Not really convinced these comments add anything the code isn't
> > already saying.
>
> We have added similar comments in tgl_ddi_pre_enable_dp(), it helps
> tracks the code with BSpec steps.
Just noise IMO. If the code isn't self explanatory then it should be
fixed instead.
>
> >
> > > + if (INTEL_GEN(dev_priv) >= 12)
> > > + intel_ddi_disable_pipe_clock(old_crtc_state);
> >
> > That's much later than the bspec sequence suggests.
>
> Oh, thanks.
> Yeah it should right after intel_disable_ddi_buf()
>
> >
> > > intel_ddi_clk_disable(encoder);
> > > tgl_clear_psr2_transcoder_exitline(old_crtc_state);
> > > }
> > > diff --git a/drivers/gpu/drm/i915/display/intel_dp_mst.c
> > > b/drivers/gpu/drm/i915/display/intel_dp_mst.c
> > > index 94549848653a..53afe3e179f7 100644
> > > --- a/drivers/gpu/drm/i915/display/intel_dp_mst.c
> > > +++ b/drivers/gpu/drm/i915/display/intel_dp_mst.c
> > > @@ -369,8 +369,19 @@ static void intel_mst_post_disable_dp(struct
> > > intel_encoder *encoder,
> > > struct intel_dp *intel_dp = &intel_dig_port->dp;
> > > struct intel_connector *connector =
> > > to_intel_connector(old_conn_state->connector);
> > > + struct drm_i915_private *dev_priv = to_i915(connector-
> > > >base.dev);
> > >
> > > - intel_ddi_disable_pipe_clock(old_crtc_state);
> > > + intel_dp->active_mst_links--;
> > > +
> > > + /*
> > > + * From TGL BSpec "If multi-stream slave transcoder: Configure
> > > + * Transcoder Clock Select to direct no clock to the
> > > transcoder"
> > > + *
> > > + * From older GENs BSpec "Configure Transcoder Clock Select to
> > > direct
> > > + * no clock to the transcoder"
> > > + */
> > > + if (INTEL_GEN(dev_priv) < 12 || intel_dp->active_mst_links)
> >
> > Maybe we should add 'last_mst_stream' to mirror the
> > 'first_mst_stream'
> > in the enable code?
>
> Sounds good
>
> >
> > > + intel_ddi_disable_pipe_clock(old_crtc_state);
> > >
> > > /* this can fail */
> > > drm_dp_check_act_status(&intel_dp->mst_mgr);
> > > @@ -386,8 +397,6 @@ static void intel_mst_post_disable_dp(struct
> > > intel_encoder *encoder,
> > > drm_dp_send_power_updown_phy(&intel_dp->mst_mgr, connector-
> > > >port,
> > > false);
> > >
> > > - intel_dp->active_mst_links--;
> > > -
> > > intel_mst->connector = NULL;
> > > if (intel_dp->active_mst_links == 0) {
> > > intel_dig_port->base.post_disable(&intel_dig_port-
> > > >base,
> > > --
> > > 2.24.0
> > >
> > > _______________________________________________
> > > Intel-gfx mailing list
> > > Intel-gfx at lists.freedesktop.org
> > > https://lists.freedesktop.org/mailman/listinfo/intel-gfx
--
Ville Syrjälä
Intel
More information about the Intel-gfx
mailing list