[Intel-gfx] [PATCH v8 4/4] drm/i915: Correctly map DBUF slices to pipes
Lisovskiy, Stanislav
stanislav.lisovskiy at intel.com
Thu Dec 19 11:58:13 UTC 2019
On Wed, 2019-12-18 at 20:05 +0200, Ville Syrjälä wrote:
> On Fri, Dec 13, 2019 at 03:02:28PM +0200, Stanislav Lisovskiy wrote:
> > Added proper DBuf slice mapping to correspondent
> > pipes, depending on pipe configuration as stated
> > in BSpec.
> >
> > v2:
> > - Remove unneeded braces
> > - Stop using macro for DBuf assignments as
> > it seems to reduce readability.
> >
> > v3: Start using enabled slices mask in dev_priv
> >
> > v4: Renamed "enabled_slices" used in dev_priv
> > to "enabled_dbuf_slices_mask"(Matt Roper)
> >
> > Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy at intel.com>
> > ---
> > drivers/gpu/drm/i915/intel_pm.c | 226
> > ++++++++++++++++++++++++++++++--
> > 1 file changed, 216 insertions(+), 10 deletions(-)
> >
> > diff --git a/drivers/gpu/drm/i915/intel_pm.c
> > b/drivers/gpu/drm/i915/intel_pm.c
> > index 111bcafd6e4c..a13052b2c2ef 100644
> > --- a/drivers/gpu/drm/i915/intel_pm.c
> > +++ b/drivers/gpu/drm/i915/intel_pm.c
> > @@ -3832,13 +3832,30 @@ bool intel_can_enable_sagv(struct
> > intel_atomic_state *state)
> > return true;
> > }
> >
> > +/*
> > + * Calculate initial DBuf slice offset, based on slice size
> > + * and mask(i.e if slice size is 1024 and second slice is enabled
> > + * offset would be 1024)
> > + */
> > +static u32 icl_get_first_dbuf_slice_offset(u32 dbuf_slice_mask,
> > + u32 slice_size, u32
> > ddb_size)
>
> s/u32/unsigned int/ or something. No point in using sized types when
> we're not dealing with some thing that is actually that size.
>
> > +{
> > + u32 offset = 0;
> > +
> > + if (!dbuf_slice_mask)
> > + return 0;
> > +
> > + offset = (ffs(dbuf_slice_mask) - 1) * slice_size;
> > +
> > + WARN_ON(offset >= ddb_size);
> > + return offset;
> > +}
> > +
> > static u16 intel_get_ddb_size(struct drm_i915_private *dev_priv,
> > const struct intel_crtc_state
> > *crtc_state,
> > const u64 total_data_rate,
> > const int num_active)
> > {
> > - struct drm_atomic_state *state = crtc_state->uapi.state;
> > - struct intel_atomic_state *intel_state =
> > to_intel_atomic_state(state);
> > u16 ddb_size = INTEL_INFO(dev_priv)->ddb_size;
> >
> > WARN_ON(ddb_size == 0);
> > @@ -3846,12 +3863,13 @@ static u16 intel_get_ddb_size(struct
> > drm_i915_private *dev_priv,
> > if (INTEL_GEN(dev_priv) < 11)
> > return ddb_size - 4; /* 4 blocks for bypass path
> > allocation */
> >
> > - intel_state->enabled_dbuf_slices_mask = DBUF_S1_BIT;
> > - ddb_size /= 2;
> > -
> > return ddb_size;
> > }
> >
> > +u32 i915_possible_dbuf_slices(struct drm_i915_private *dev_priv,
> > + int pipe, u32 active_pipes,
> > + const struct intel_crtc_state
> > *crtc_state);
> > +
> > static void
> > skl_ddb_get_pipe_allocation_limits(struct drm_i915_private
> > *dev_priv,
> > const struct intel_crtc_state
> > *crtc_state,
> > @@ -3866,7 +3884,14 @@ skl_ddb_get_pipe_allocation_limits(struct
> > drm_i915_private *dev_priv,
> > u32 pipe_width = 0, total_width = 0, width_before_pipe = 0;
> > enum pipe for_pipe = to_intel_crtc(for_crtc)->pipe;
> > u16 ddb_size;
> > + u32 ddb_range_size;
> > u32 i;
> > + u32 dbuf_slice_mask;
> > + u32 active_pipes;
> > + u32 offset;
> > + u32 slice_size;
> > + u32 total_slice_mask;
> > + u32 start, end;
> >
> > if (WARN_ON(!state) || !crtc_state->hw.active) {
> > alloc->start = 0;
> > @@ -3875,14 +3900,19 @@ skl_ddb_get_pipe_allocation_limits(struct
> > drm_i915_private *dev_priv,
> > return;
> > }
> >
> > - if (intel_state->active_pipe_changes)
> > + if (intel_state->active_pipe_changes) {
> > *num_active = hweight8(intel_state->active_pipes);
> > - else
> > + active_pipes = intel_state->active_pipes;
> > + } else {
> > *num_active = hweight8(dev_priv->active_pipes);
> > + active_pipes = dev_priv->active_pipes;
> > + }
> >
> > ddb_size = intel_get_ddb_size(dev_priv, crtc_state,
> > total_data_rate,
> > *num_active);
> >
> > + slice_size = ddb_size / INTEL_INFO(dev_priv)-
> > >num_supported_dbuf_slices;
> > +
> > /*
> > * If the state doesn't change the active CRTC's or there is no
> > * modeset request, then there's no need to recalculate;
> > @@ -3900,18 +3930,68 @@ skl_ddb_get_pipe_allocation_limits(struct
> > drm_i915_private *dev_priv,
> > return;
> > }
> >
> > + /*
> > + * Get allowed DBuf slices for correspondent pipe and platform.
> > + */
> > + dbuf_slice_mask = i915_possible_dbuf_slices(dev_priv, for_pipe,
> > + active_pipes,
> > crtc_state);
> > +
> > + DRM_DEBUG_KMS("DBuf slice mask %x pipe %d active pipes %x\n",
> > + dbuf_slice_mask,
> > + for_pipe, active_pipes);
> > +
> > + /*
> > + * Figure out at which DBuf slice we start, i.e if we start at
> > Dbuf S2
> > + * and slice size is 1024, the offset would be 1024
> > + */
> > + offset = icl_get_first_dbuf_slice_offset(dbuf_slice_mask,
> > + slice_size, ddb_size);
> > +
> > + /*
> > + * Figure out total size of allowed DBuf slices, which is
> > basically
> > + * a number of allowed slices for that pipe multiplied by slice
> > size.
> > + * Inside of this
> > + * range ddb entries are still allocated in proportion to
> > display width.
> > + */
> > + ddb_range_size = hweight8(dbuf_slice_mask) * slice_size;
> > +
> > /*
> > * Watermark/ddb requirement highly depends upon width of the
> > * framebuffer, So instead of allocating DDB equally among
> > pipes
> > * distribute DDB based on resolution/width of the display.
> > */
> > + total_slice_mask = dbuf_slice_mask;
> > for_each_new_intel_crtc_in_state(intel_state, crtc, crtc_state,
> > i) {
> > const struct drm_display_mode *adjusted_mode =
> > &crtc_state->hw.adjusted_mode;
> > enum pipe pipe = crtc->pipe;
> > int hdisplay, vdisplay;
> > + u32 pipe_dbuf_slice_mask =
> > + i915_possible_dbuf_slices(dev_p
> > riv,
> > + pipe,
> > + activ
> > e_pipes,
> > + crtc_
> > state);
> > +
> > + if (!crtc_state->hw.active)
> > + continue;
> > +
> > + /*
> > + * According to BSpec pipe can share one dbuf slice
> > with another
> > + * pipes or pipe can use multiple dbufs, in both cases
> > we
> > + * account for other pipes only if they have exactly
> > same mask.
> > + * However we need to account how many slices we should
> > enable
> > + * in total.
> > + */
> > + total_slice_mask |= pipe_dbuf_slice_mask;
> >
> > - if (!crtc_state->hw.enable)
> > + /*
> > + * Do not account pipes using other slice sets
> > + * luckily as of current BSpec slice sets do not
> > partially
> > + * intersect(pipes share either same one slice or same
> > slice set
> > + * i.e no partial intersection), so it is enough to
> > check for
> > + * equality for now.
> > + */
> > + if (dbuf_slice_mask != pipe_dbuf_slice_mask)
> > continue;
> >
> > drm_mode_get_hv_timing(adjusted_mode, &hdisplay,
> > &vdisplay);
> > @@ -3923,8 +4003,19 @@ skl_ddb_get_pipe_allocation_limits(struct
> > drm_i915_private *dev_priv,
> > pipe_width = hdisplay;
> > }
> >
> > - alloc->start = ddb_size * width_before_pipe / total_width;
> > - alloc->end = ddb_size * (width_before_pipe + pipe_width) /
> > total_width;
> > + intel_state->enabled_dbuf_slices_mask = total_slice_mask;
> > +
> > + start = ddb_range_size * width_before_pipe / total_width;
> > + end = ddb_range_size * (width_before_pipe + pipe_width) /
> > total_width;
> > +
> > + alloc->start = offset + start;
> > + alloc->end = offset + end;
> > +
> > + DRM_DEBUG_KMS("Pipe %d ddb %d-%d\n", for_pipe,
> > + alloc->start, alloc->end);
> > + DRM_DEBUG_KMS("Enabled ddb slices mask %x num supported %d\n",
> > + intel_state->enabled_dbuf_slices_mask,
> > + INTEL_INFO(dev_priv)->num_supported_dbuf_slices);
> > }
>
> That function really is quite the monster. Probably needs to be split
> up
> into sensible chunks... later.
>
> >
> > static int skl_compute_wm_params(const struct intel_crtc_state
> > *crtc_state,
> > @@ -4094,6 +4185,121 @@ skl_plane_downscale_amount(const struct
> > intel_crtc_state *crtc_state,
> > return mul_fixed16(downscale_w, downscale_h);
> > }
> >
> > +struct dbuf_slice_conf_entry {
> > + u32 active_pipes;
> > + u32 dbuf_mask[I915_MAX_PIPES];
>
> u8 will do for everything.
>
> > +};
> > +
> > +/*
> > + * Table taken from Bspec 12716
> > + * Pipes do have some preferred DBuf slice affinity,
> > + * plus there are some hardcoded requirements on how
> > + * those should be distributed for multipipe scenarios.
> > + * For more DBuf slices algorithm can get even more messy
> > + * and less readable, so decided to use a table almost
> > + * as is from BSpec itself - that way it is at least easier
> > + * to compare, change and check.
> > + */
> > +static struct dbuf_slice_conf_entry icl_allowed_dbufs[] = {
> > + { BIT(PIPE_A), { DBUF_S1_BIT, 0, 0, 0 } },
>
> Still don't like that DBUF_S1_BIT. I still think it should be an
> enum dbuf_slice + explcit BIT(DBUF_S1) where needed.
>
> And please use named initializers instead of sprinkling zeroes.
> IMO this should just look something like:
>
> { .active_pipes = BIT(PIPE_A) | BIT(PIPE_B),
> .dbuf_slices = { [PIPE_A] = BIT(DBUF_S1),
> [PIPE_B] = BIT(DBUF_S2),
> },
> },
>
> > + { BIT(PIPE_B), { 0, DBUF_S1_BIT, 0, 0 } },
> > + { BIT(PIPE_C), { 0, 0, DBUF_S2_BIT, 0 } },
> > + { BIT(PIPE_A) | BIT(PIPE_B), { DBUF_S1_BIT, DBUF_S2_BIT, 0, 0 }
> > },
> > + { BIT(PIPE_A) | BIT(PIPE_C), { DBUF_S1_BIT, 0, DBUF_S2_BIT, 0 }
> > },
> > + { BIT(PIPE_B) | BIT(PIPE_C), { 0, DBUF_S1_BIT, DBUF_S2_BIT, 0 }
> > },
> > + { BIT(PIPE_A) | BIT(PIPE_B) | BIT(PIPE_C),
> > + { DBUF_S1_BIT, DBUF_S1_BIT, DBUF_S2_BIT, 0 } }
> > +};
> > +
> > +/*
> > + * Table taken from Bspec 49255
> > + * Pipes do have some preferred DBuf slice affinity,
> > + * plus there are some hardcoded requirements on how
> > + * those should be distributed for multipipe scenarios.
> > + * For more DBuf slices algorithm can get even more messy
> > + * and less readable, so decided to use a table almost
> > + * as is from BSpec itself - that way it is at least easier
> > + * to compare, change and check.
> > + */
> > +static struct dbuf_slice_conf_entry tgl_allowed_dbufs[] = {
> > + { BIT(PIPE_A), { DBUF_S1_BIT | DBUF_S2_BIT, 0, 0, 0 } },
> > + { BIT(PIPE_B), { 0, DBUF_S1_BIT | DBUF_S2_BIT, 0, 0 } },
> > + { BIT(PIPE_C), { 0, 0, DBUF_S1_BIT | DBUF_S2_BIT, 0 } },
> > + { BIT(PIPE_D), { 0, 0, 0, DBUF_S1_BIT | DBUF_S2_BIT } },
> > + { BIT(PIPE_A) | BIT(PIPE_B), { DBUF_S2_BIT, DBUF_S1_BIT, 0, 0 }
> > },
> > + { BIT(PIPE_A) | BIT(PIPE_C), { DBUF_S1_BIT, 0, DBUF_S2_BIT, 0 }
> > },
> > + { BIT(PIPE_A) | BIT(PIPE_D), { DBUF_S1_BIT, 0, 0, DBUF_S2_BIT }
> > },
> > + { BIT(PIPE_B) | BIT(PIPE_C), { 0, DBUF_S1_BIT, DBUF_S2_BIT, 0 }
> > },
> > + { BIT(PIPE_B) | BIT(PIPE_D), { 0, DBUF_S1_BIT, 0, DBUF_S2_BIT }
> > },
> > + { BIT(PIPE_C) | BIT(PIPE_D), { 0, 0, DBUF_S2_BIT, DBUF_S2_BIT }
> > },
>
> I believe pipe C should use S1 here.
Thanks for spotting. Actually my generator says it as well, just didn't
use it for checking. BTW can you review that one as well - I think
it might be useful to keep in igt/tools, to avoid exactly typos like
this.
>
> > + { BIT(PIPE_A) | BIT(PIPE_B) | BIT(PIPE_C),
> > + { DBUF_S1_BIT, DBUF_S1_BIT, DBUF_S2_BIT, 0 } },
> > + { BIT(PIPE_A) | BIT(PIPE_B) | BIT(PIPE_D),
> > + { DBUF_S1_BIT, DBUF_S1_BIT, 0, DBUF_S2_BIT } },
> > + { BIT(PIPE_A) | BIT(PIPE_C) | BIT(PIPE_D),
> > + { DBUF_S1_BIT, 0, DBUF_S2_BIT, DBUF_S2_BIT } },
> > + { BIT(PIPE_B) | BIT(PIPE_C) | BIT(PIPE_D),
> > + { 0, DBUF_S1_BIT, DBUF_S2_BIT, DBUF_S2_BIT } },
> > + { BIT(PIPE_A) | BIT(PIPE_B) | BIT(PIPE_C) | BIT(PIPE_D),
> > + { DBUF_S1_BIT, DBUF_S1_BIT, DBUF_S2_BIT, DBUF_S2_BIT }
> > },
> > +};
> > +
> > +static u32 i915_find_pipe_conf(int pipe,
>
> enum pipe pipe
>
> > + u32 active_pipes,
> > + const struct dbuf_slice_conf_entry
> > *dbuf_slices,
> > + int size)
>
> Could just add a sentinel to the end of the arrays and avoid this
> 'size' stuff.
>
> The function name is still very confusing. icl_compute_dbuf_slices()
> or something perhaps. Or even without a prefix since it's static
> anyway.
>
> > +{
> > + int i;
> > +
> > + for (i = 0; i < size; i++) {
> > + if (dbuf_slices[i].active_pipes == active_pipes)
> > + return dbuf_slices[i].dbuf_mask[pipe];
> > + }
> > + return 0;
> > +}
> > +
> > +/*
> > + * This function finds an entry with same enabled pipe
> > configuration and
> > + * returns correspondent DBuf slice mask as stated in BSpec for
> > particular
> > + * platform.
> > + */
> > +static u32 icl_possible_dbuf_slices(int pipe,
> > + u32 active_pipes,
> > + const struct intel_crtc_state
> > *crtc_state)
> > +{
> > + return i915_find_pipe_conf(pipe, active_pipes,
> > + icl_allowed_dbufs,
> > + ARRAY_SIZE(icl_allowed_dbufs));
> > +}
> > +
> > +static u32 tgl_possible_dbuf_slices(int pipe,
> > + u32 active_pipes,
> > + const struct intel_crtc_state
> > *crtc_state)
> > +{
> > + return i915_find_pipe_conf(pipe, active_pipes,
> > + tgl_allowed_dbufs,
> > + ARRAY_SIZE(tgl_allowed_dbufs));
> > +}
>
> These wrappers aren't really doing anything for us.
>
> > +
> > +u32 i915_possible_dbuf_slices(struct drm_i915_private *dev_priv,
>
> dev_priv and pipe are redundant parameters. Both
> can be extracted from crtc_state. I would put crtc_state as the first
> parameter. Matches common practice more closely.
>
> s/i915/skl/ in the function name.
>
> > + int pipe, u32 active_pipes,
> > + const struct intel_crtc_state
> > *crtc_state)
> > +{
> > + if (IS_GEN(dev_priv, 11))
> > + return icl_possible_dbuf_slices(pipe,
> > + active_pipes,
> > + crtc_state);
> > + else if (IS_GEN(dev_priv, 12))
> > + return tgl_possible_dbuf_slices(pipe,
> > + active_pipes,
> > + crtc_state);
>
> The established convention is to go from new platforms
> to old platforms, if possible.
>
> > + /*
> > + * For anything else just return one slice yet.
> > + * Should be extended for other platforms.
> > + */
> > + return DBUF_S1_BIT;
> > +}
> > +
> > static u64
> > skl_plane_relative_data_rate(const struct intel_crtc_state
> > *crtc_state,
> > const struct intel_plane_state
> > *plane_state,
> > --
> > 2.17.1
>
>
More information about the Intel-gfx
mailing list