[Intel-gfx] [PATCH 1/2] drm/i915: Fix fastset vs. pfit on/off on HSW EDP transcoder

[Maarten Lankhorst]

Op 25-04-2019 om 18:29 schreef Ville Syrjala:
> From: Ville Syrjälä <ville.syrjala at linux.intel.com>
>
> On HSW the pipe A panel fitter lives inside the display power well,
> and the input MUX for the EDP transcoder needs to be configured
> appropriately to route the data through the power well as needed.
> Changing the MUX setting is not allowed while the pipe is active,
> so we need to force a full modeset whenever we need to change it.
>
> Currently we may end up doing a fastset which won't change the
> MUX settings, but it will drop the power well reference, and that
> kills the pipe.
>
> Cc: stable at vger.kernel.org
> Cc: Hans de Goede <hdegoede at redhat.com>
> Cc: Maarten Lankhorst <maarten.lankhorst at linux.intel.com>
> Fixes: d19f958db23c ("drm/i915: Enable fastset for non-boot modesets.")
> Signed-off-by: Ville Syrjälä <ville.syrjala at linux.intel.com>
> ---
>  drivers/gpu/drm/i915/intel_display.c  |  9 +++++++++
>  drivers/gpu/drm/i915/intel_pipe_crc.c | 13 ++++++++++---
>  2 files changed, 19 insertions(+), 3 deletions(-)
>
> diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c
> index c67f165b466c..691c9a929164 100644
> --- a/drivers/gpu/drm/i915/intel_display.c
> +++ b/drivers/gpu/drm/i915/intel_display.c
> @@ -12133,6 +12133,7 @@ intel_pipe_config_compare(struct drm_i915_private *dev_priv,
>  			  struct intel_crtc_state *pipe_config,
>  			  bool adjust)
>  {
> +	struct intel_crtc *crtc = to_intel_crtc(current_config->base.crtc);
>  	bool ret = true;
>  	bool fixup_inherited = adjust &&
>  		(current_config->base.mode.private_flags & I915_MODE_FLAG_INHERITED) &&
> @@ -12354,6 +12355,14 @@ intel_pipe_config_compare(struct drm_i915_private *dev_priv,
>  		PIPE_CONF_CHECK_X(gmch_pfit.pgm_ratios);
>  	PIPE_CONF_CHECK_X(gmch_pfit.lvds_border_bits);
>  
> +	/*
> +	 * Changing the EDP transcoder input mux
> +	 * (A_ONOFF vs. A_ON) requires a full modeset.
> +	 */
> +	if (IS_HASWELL(dev_priv) && crtc->pipe == PIPE_A &&
> +	    current_config->cpu_transcoder == TRANSCODER_EDP)
> +		PIPE_CONF_CHECK_BOOL(pch_pfit.enabled);

I guess it depends if we want to make it a blocker or not..

> +
>  	if (!adjust) {
>  		PIPE_CONF_CHECK_I(pipe_src_w);
>  		PIPE_CONF_CHECK_I(pipe_src_h);
> diff --git a/drivers/gpu/drm/i915/intel_pipe_crc.c b/drivers/gpu/drm/i915/intel_pipe_crc.c
> index e94b5b1bc1b7..e7c7be4911c1 100644
> --- a/drivers/gpu/drm/i915/intel_pipe_crc.c
> +++ b/drivers/gpu/drm/i915/intel_pipe_crc.c
> @@ -311,10 +311,17 @@ intel_crtc_crc_setup_workarounds(struct intel_crtc *crtc, bool enable)
>  	pipe_config->base.mode_changed = pipe_config->has_psr;
>  	pipe_config->crc_enabled = enable;
>  
> -	if (IS_HASWELL(dev_priv) && crtc->pipe == PIPE_A) {
> +	if (IS_HASWELL(dev_priv) &&
> +	    pipe_config->base.active && crtc->pipe == PIPE_A &&
> +	    pipe_config->cpu_transcoder == TRANSCODER_EDP) {
> +		bool old_need_power_well = pipe_config->pch_pfit.enabled ||
> +			pipe_config->pch_pfit.force_thru;
> +		bool new_need_power_well = pipe_config->pch_pfit.enabled ||
> +			enable;
> +
>  		pipe_config->pch_pfit.force_thru = enable;
> -		if (pipe_config->cpu_transcoder == TRANSCODER_EDP &&
> -		    pipe_config->pch_pfit.enabled != enable)
> +
> +		if (old_need_power_well != new_need_power_well)
>  			pipe_config->base.connectors_changed = true;

Could we get rid of this logic and set mode_changed instead?

Ah, I see that is done in 2/2, much less surprises then. :)

In that case, for both:

Reviewed-by: Maarten Lankhorst <maarten.lankhorst at linux.intel.com>