[Intel-gfx] [RFC-v2 3/9] drm/i915/dsi: Add vblank calculation for command mode

[Vandita Kulkarni]

Transcoder timing calculation differ for command mode.

v2: Use is_vid_mode, and use same I915_WRITE (Jani)

Signed-off-by: Vandita Kulkarni <vandita.kulkarni at intel.com>
---
 drivers/gpu/drm/i915/display/icl_dsi.c | 39 +++++++++++++++++---------
 1 file changed, 26 insertions(+), 13 deletions(-)

diff --git a/drivers/gpu/drm/i915/display/icl_dsi.c b/drivers/gpu/drm/i915/display/icl_dsi.c
index 5ff2a1ffd3ea..488620365f76 100644
--- a/drivers/gpu/drm/i915/display/icl_dsi.c
+++ b/drivers/gpu/drm/i915/display/icl_dsi.c
@@ -780,6 +780,7 @@ gen11_dsi_set_transcoder_timings(struct intel_encoder *encoder,
 	u16 hback_porch;
 	/* vertical timings */
 	u16 vtotal, vactive, vsync_start, vsync_end, vsync_shift;
+	int bpp, line_time_us, byte_clk_period_ns;
 
 	hactive = adjusted_mode->crtc_hdisplay;
 	htotal = adjusted_mode->crtc_htotal;
@@ -817,7 +818,7 @@ gen11_dsi_set_transcoder_timings(struct intel_encoder *encoder,
 	}
 
 	/* TRANS_HSYNC register to be programmed only for video mode */
-	if (intel_dsi->operation_mode == INTEL_DSI_VIDEO_MODE) {
+	if (is_vid_mode(intel_dsi)) {
 		if (intel_dsi->video_mode_format ==
 		    VIDEO_MODE_NON_BURST_WITH_SYNC_PULSE) {
 			/* BSPEC: hsync size should be atleast 16 pixels */
@@ -841,12 +842,20 @@ gen11_dsi_set_transcoder_timings(struct intel_encoder *encoder,
 	}
 
 	/* program TRANS_VTOTAL register */
+	if (is_cmd_mode(intel_dsi)) {
+		bpp = mipi_dsi_pixel_format_to_bpp(intel_dsi->pixel_format);
+		byte_clk_period_ns = 8 * 1000000 / intel_dsi->pclk;
+		htotal = hactive + 160;
+		line_time_us = (htotal * (bpp / 8) * byte_clk_period_ns) / (1000 * intel_dsi->lane_count);
+		vtotal = vactive + DIV_ROUND_UP(460, line_time_us);
+	}
+
 	for_each_dsi_port(port, intel_dsi->ports) {
 		dsi_trans = dsi_port_to_transcoder(port);
 		/*
-		 * FIXME: Programing this by assuming progressive mode, since
-		 * non-interlaced info from VBT is not saved inside
-		 * struct drm_display_mode.
+		 * FIXME: Programing this by assuming progressive mode,
+		 * since non-interlaced info from VBT is not saved
+		 * inside struct drm_display_mode.
 		 * For interlace mode: program required pixel minus 2
 		 */
 		I915_WRITE(VTOTAL(dsi_trans),
@@ -859,22 +868,26 @@ gen11_dsi_set_transcoder_timings(struct intel_encoder *encoder,
 	if (vsync_start < vactive)
 		DRM_ERROR("vsync_start less than vactive\n");
 
-	/* program TRANS_VSYNC register */
-	for_each_dsi_port(port, intel_dsi->ports) {
-		dsi_trans = dsi_port_to_transcoder(port);
-		I915_WRITE(VSYNC(dsi_trans),
-			   (vsync_start - 1) | ((vsync_end - 1) << 16));
+	/* program TRANS_VSYNC register for video mode only */
+	if (is_vid_mode(intel_dsi)) {
+		for_each_dsi_port(port, intel_dsi->ports) {
+			dsi_trans = dsi_port_to_transcoder(port);
+			I915_WRITE(VSYNC(dsi_trans),
+				   (vsync_start - 1) | ((vsync_end - 1) << 16));
+		}
 	}
 
 	/*
-	 * FIXME: It has to be programmed only for interlaced
+	 * FIXME: It has to be programmed only for video modes and interlaced
 	 * modes. Put the check condition here once interlaced
 	 * info available as described above.
 	 * program TRANS_VSYNCSHIFT register
 	 */
-	for_each_dsi_port(port, intel_dsi->ports) {
-		dsi_trans = dsi_port_to_transcoder(port);
-		I915_WRITE(VSYNCSHIFT(dsi_trans), vsync_shift);
+	if (is_vid_mode(intel_dsi)) {
+		for_each_dsi_port(port, intel_dsi->ports) {
+			dsi_trans = dsi_port_to_transcoder(port);
+			I915_WRITE(VSYNCSHIFT(dsi_trans), vsync_shift);
+		}
 	}
 
 	/* program TRANS_VBLANK register, should be same as vtotal programmed */
-- 
2.21.0.5.gaeb582a