[Intel-gfx] [PATCH 3/3] drm/i915/dc3co: Avoid full modeset when EXITLINE needs to be changed
Souza, Jose
jose.souza at intel.com
Mon Nov 18 18:42:35 UTC 2019
On Sun, 2019-11-17 at 18:23 +0530, Anshuamn Gupta wrote:
> On 2019-10-31 at 17:14:22 -0700, José Roberto de Souza wrote:
> > A recent change in BSpec allow us to change EXTLINE while
> > transcoder
> > is enabled so this allow us to change it even when doing the first
> > fastset after taking over previous hardware state set by BIOS.
> > BIOS don't enable PSR, so if sink supports PSR it will be enabled
> > on
> > the first fastset, so moving the EXTLINE compute and set to PSR
> > flows
> > allow us to simplfy a bunch of code.
> >
> > This will save a lot of time in all the IGT tests that uses CRC, as
> > when PSR2 is enabled CRCs are not generated, so we switch to PSR1,
> > so
> > the previous code would compute dc3co_exitline=0 causing a full
> > modeset that would shutdown pipe, enable and train link.
> >
> > BSpec: 49196
> > Cc: Imre Deak <imre.deak at intel.com>
> > Cc: Anshuman Gupta <anshuman.gupta at intel.com>
> > Signed-off-by: José Roberto de Souza <jose.souza at intel.com>
> > ---
> > drivers/gpu/drm/i915/display/intel_ddi.c | 86 ----------------
> > ----
> > drivers/gpu/drm/i915/display/intel_display.c | 1 -
> > drivers/gpu/drm/i915/display/intel_psr.c | 47 +++++++++++
> > 3 files changed, 47 insertions(+), 87 deletions(-)
> >
> > diff --git a/drivers/gpu/drm/i915/display/intel_ddi.c
> > b/drivers/gpu/drm/i915/display/intel_ddi.c
> > index b51f244ad7a5..f52fb7619d46 100644
> > --- a/drivers/gpu/drm/i915/display/intel_ddi.c
> > +++ b/drivers/gpu/drm/i915/display/intel_ddi.c
> > @@ -3339,86 +3339,6 @@ static void
> > intel_ddi_disable_fec_state(struct intel_encoder *encoder,
> > POSTING_READ(intel_dp->regs.dp_tp_ctl);
> > }
> >
> > -static void
> > -tgl_clear_psr2_transcoder_exitline(const struct intel_crtc_state
> > *cstate)
> > -{
> > - struct drm_i915_private *dev_priv = to_i915(cstate->base.crtc-
> > >dev);
> > - u32 val;
> > -
> > - if (!cstate->dc3co_exitline)
> > - return;
> > -
> > - val = I915_READ(EXITLINE(cstate->cpu_transcoder));
> > - val &= ~(EXITLINE_MASK | EXITLINE_ENABLE);
> > - I915_WRITE(EXITLINE(cstate->cpu_transcoder), val);
> > -}
> > -
> > -static void
> > -tgl_set_psr2_transcoder_exitline(const struct intel_crtc_state
> > *cstate)
> > -{
> > - u32 val, exit_scanlines;
> > - struct drm_i915_private *dev_priv = to_i915(cstate->base.crtc-
> > >dev);
> > -
> > - if (!cstate->dc3co_exitline)
> > - return;
> > -
> > - exit_scanlines = cstate->dc3co_exitline;
> > - exit_scanlines <<= EXITLINE_SHIFT;
> > - val = I915_READ(EXITLINE(cstate->cpu_transcoder));
> > - val &= ~(EXITLINE_MASK | EXITLINE_ENABLE);
> > - val |= exit_scanlines;
> > - val |= EXITLINE_ENABLE;
> > - I915_WRITE(EXITLINE(cstate->cpu_transcoder), val);
> > -}
> > -
> > -static void tgl_dc3co_exitline_compute_config(struct intel_encoder
> > *encoder,
> > - struct intel_crtc_state
> > *cstate)
> > -{
> > - u32 exit_scanlines;
> > - struct drm_i915_private *dev_priv = to_i915(cstate->base.crtc-
> > >dev);
> > - u32 crtc_vdisplay = cstate->base.adjusted_mode.crtc_vdisplay;
> > -
> > - cstate->dc3co_exitline = 0;
> > -
> > - if (!(dev_priv->csr.allowed_dc_mask & DC_STATE_EN_DC3CO))
> > - return;
> > -
> > - /* B.Specs:49196 DC3CO only works with pipeA and DDIA.*/
> > - if (to_intel_crtc(cstate->base.crtc)->pipe != PIPE_A ||
> > - encoder->port != PORT_A)
> > - return;
> > -
> > - if (!cstate->has_psr2 || !cstate->base.active)
> > - return;
> > -
> > - /*
> > - * DC3CO Exit time 200us B.Spec 49196
> > - * PSR2 transcoder Early Exit scanlines = ROUNDUP(200 / line
> > time) + 1
> > - */
> > - exit_scanlines =
> > - intel_usecs_to_scanlines(&cstate->base.adjusted_mode,
> > 200) + 1;
> > -
> > - if (WARN_ON(exit_scanlines > crtc_vdisplay))
> > - return;
> > -
> > - cstate->dc3co_exitline = crtc_vdisplay - exit_scanlines;
> > - DRM_DEBUG_KMS("DC3CO exit scanlines %d\n", cstate-
> > >dc3co_exitline);
> > -}
> > -
> > -static void tgl_dc3co_exitline_get_config(struct intel_crtc_state
> > *crtc_state)
> > -{
> > - u32 val;
> > - struct drm_i915_private *dev_priv = to_i915(crtc_state-
> > >base.crtc->dev);
> > -
> > - if (INTEL_GEN(dev_priv) < 12)
> > - return;
> > -
> > - val = I915_READ(EXITLINE(crtc_state->cpu_transcoder));
> > -
> > - if (val & EXITLINE_ENABLE)
> > - crtc_state->dc3co_exitline = val & EXITLINE_MASK;
> > -}
> > -
> > static void tgl_ddi_pre_enable_dp(struct intel_encoder *encoder,
> > const struct intel_crtc_state
> > *crtc_state,
> > const struct drm_connector_state
> > *conn_state)
> > @@ -3431,7 +3351,6 @@ static void tgl_ddi_pre_enable_dp(struct
> > intel_encoder *encoder,
> > int level = intel_ddi_dp_level(intel_dp);
> > enum transcoder transcoder = crtc_state->cpu_transcoder;
> >
> > - tgl_set_psr2_transcoder_exitline(crtc_state);
> > intel_dp_set_link_params(intel_dp, crtc_state->port_clock,
> > crtc_state->lane_count, is_mst);
> >
> > @@ -3760,7 +3679,6 @@ static void intel_ddi_post_disable_dp(struct
> > intel_encoder *encoder,
> > dig_port-
> > >ddi_io_power_domain);
> >
> > intel_ddi_clk_disable(encoder);
> > - tgl_clear_psr2_transcoder_exitline(old_crtc_state);
> > }
> >
> > static void intel_ddi_post_disable_hdmi(struct intel_encoder
> > *encoder,
> > @@ -4308,9 +4226,6 @@ void intel_ddi_get_config(struct
> > intel_encoder *encoder,
> > break;
> > }
> >
> > - if (encoder->type == INTEL_OUTPUT_EDP)
> > - tgl_dc3co_exitline_get_config(pipe_config);
> > -
> > pipe_config->has_audio =
> > intel_ddi_is_audio_enabled(dev_priv, cpu_transcoder);
> >
> > @@ -4392,7 +4307,6 @@ static int intel_ddi_compute_config(struct
> > intel_encoder *encoder,
> > ret = intel_hdmi_compute_config(encoder, pipe_config,
> > conn_state);
> > } else {
> > ret = intel_dp_compute_config(encoder, pipe_config,
> > conn_state);
> > - tgl_dc3co_exitline_compute_config(encoder,
> > pipe_config);
> > }
> >
> > if (ret)
> > diff --git a/drivers/gpu/drm/i915/display/intel_display.c
> > b/drivers/gpu/drm/i915/display/intel_display.c
> > index 348ce0456696..6c1c93b2a81f 100644
> > --- a/drivers/gpu/drm/i915/display/intel_display.c
> > +++ b/drivers/gpu/drm/i915/display/intel_display.c
> > @@ -13091,7 +13091,6 @@ intel_pipe_config_compare(const struct
> > intel_crtc_state *current_config,
> >
> > PIPE_CONF_CHECK_I(pixel_multiplier);
> > PIPE_CONF_CHECK_I(output_format);
> > - PIPE_CONF_CHECK_I(dc3co_exitline);
> > PIPE_CONF_CHECK_BOOL(has_hdmi_sink);
> > if ((INTEL_GEN(dev_priv) < 8 && !IS_HASWELL(dev_priv)) ||
> > IS_VALLEYVIEW(dev_priv) || IS_CHERRYVIEW(dev_priv))
> > diff --git a/drivers/gpu/drm/i915/display/intel_psr.c
> > b/drivers/gpu/drm/i915/display/intel_psr.c
> > index bb9b5349b72a..06a0a1c9621e 100644
> > --- a/drivers/gpu/drm/i915/display/intel_psr.c
> > +++ b/drivers/gpu/drm/i915/display/intel_psr.c
> > @@ -596,6 +596,37 @@ static void
> > tgl_disallow_dc3co_on_psr2_exit(struct drm_i915_private *dev_priv)
> > tgl_psr2_disable_dc3co(dev_priv);
> > }
> >
> > +static void
> > +tgl_dc3co_exitline_compute_config(struct intel_dp *intel_dp,
> > + struct intel_crtc_state *crtc_state)
> > +{
> > + const u32 crtc_vdisplay = crtc_state-
> > >base.adjusted_mode.crtc_vdisplay;
> > + struct intel_digital_port *dig_port = dp_to_dig_port(intel_dp);
> > + struct drm_i915_private *dev_priv = dp_to_i915(intel_dp);
> > + u32 exit_scanlines;
> We wanted to explicitly clear dc3co_exitline in case it is not
> supported.
The whole intel_crtc_state is zeroed before the compute functions are
called so no need to set dc3co_exitline to zero.
> > +
> > + if (!(dev_priv->csr.allowed_dc_mask & DC_STATE_EN_DC3CO))
> > + return;
> > +
> > + /* B.Specs:49196 DC3CO only works with pipeA and DDIA.*/
> > + if (to_intel_crtc(crtc_state->base.crtc)->pipe != PIPE_A ||
> > + dig_port->base.port != PORT_A)
> > + return;
> > +
> > + /*
> > + * DC3CO Exit time 200us B.Spec 49196
> > + * PSR2 transcoder Early Exit scanlines = ROUNDUP(200 / line
> > time) + 1
> > + */
> > + exit_scanlines =
> > + intel_usecs_to_scanlines(&crtc_state-
> > >base.adjusted_mode, 200) + 1;
> > +
> > + if (WARN_ON(exit_scanlines > crtc_vdisplay))
> > + return;
> > +
> > + crtc_state->dc3co_exitline = crtc_vdisplay - exit_scanlines;
> > + DRM_DEBUG_KMS("DC3CO exit scanlines %d\n", crtc_state-
> > >dc3co_exitline);
> > +}
> > +
> > static bool intel_psr2_config_valid(struct intel_dp *intel_dp,
> > struct intel_crtc_state
> > *crtc_state)
> > {
> > @@ -658,6 +689,7 @@ static bool intel_psr2_config_valid(struct
> > intel_dp *intel_dp,
> > return false;
> > }
> >
> > + tgl_dc3co_exitline_compute_config(intel_dp, crtc_state);
> > return true;
> > }
> >
> > @@ -775,6 +807,21 @@ static void intel_psr_enable_source(struct
> > intel_dp *intel_dp,
> > I915_WRITE(EDP_PSR_DEBUG(dev_priv->psr.transcoder), mask);
> >
> > psr_irq_control(dev_priv);
> > +
> > + if (INTEL_GEN(dev_priv) >= 12 && dev_priv->psr.psr2_enabled) {
> IMHO we can use dc3co_enabled flag here instead of psr2_enabled, and
> it would be
> nice to have a seperate function to set the exitline here.
> Thanks,
> Anshuman Gupta.
Here it is checking for PSR2 because in case DC3CO is disabled it will
set EXITLINE to 0 but we could keep it set too without any drawbacks.
Thoughts Imre?
I don't think we need a separated function it is just RMW into one
registers.
> > + u32 val;
> > +
> > + /*
> > + * TODO: if future platforms supports DC3CO in more
> > than one
> > + * transcoder, EXITLINE will need to be unset when
> > disabling PSR
> > + */
> > + val = I915_READ(EXITLINE(cpu_transcoder));
> > + val &= ~(EXITLINE_MASK | EXITLINE_ENABLE);
> > + val |= crtc_state->dc3co_exitline << EXITLINE_SHIFT;
> > + if (crtc_state->dc3co_exitline)
> > + val |= EXITLINE_ENABLE;
> > + I915_WRITE(EXITLINE(cpu_transcoder), val);
> > + }
> > }
> >
> > static void intel_psr_enable_locked(struct drm_i915_private
> > *dev_priv,
> > --
> > 2.23.0
> >
More information about the Intel-gfx
mailing list