[Intel-gfx] [PATCH v2 12/13] drm/i915: Add helper functions for calculating DSC parameters for HDMI2.1
Nautiyal, Ankit K
ankit.k.nautiyal at intel.com
Wed Dec 2 14:13:08 UTC 2020
Hi Uma,
Thanks for the comments and spotting the errors. I agree to most of the
comments and will address them in the next version.
Please find my responses inline:
On 11/26/2020 1:58 AM, Shankar, Uma wrote:
>
>> -----Original Message-----
>> From: Nautiyal, Ankit K <ankit.k.nautiyal at intel.com>
>> Sent: Sunday, November 1, 2020 3:37 PM
>> To: intel-gfx at lists.freedesktop.org
>> Cc: dri-devel at lists.freedesktop.org; Shankar, Uma <uma.shankar at intel.com>;
>> Kulkarni, Vandita <vandita.kulkarni at intel.com>; ville.syrjala at linux.intel.com;
>> Sharma, Swati2 <swati2.sharma at intel.com>
>> Subject: [PATCH v2 12/13] drm/i915: Add helper functions for calculating DSC
>> parameters for HDMI2.1
>>
>> The DP-HDMI2.1 PCON spec provides way for a source to set PPS
>> parameters: slice height, slice width and bits_per_pixel, based on the HDMI2.1
>> sink capabilities. The DSC encoder of the PCON will respect these parameters,
>> while preparing the 128 byte PPS.
>>
>> This patch adds helper functions to calculate these PPS paremeters as per the
>> HDMI2.1 specification.
>>
>> Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal at intel.com>
>> ---
>> drivers/gpu/drm/i915/display/intel_hdmi.c | 181 ++++++++++++++++++++++
>> drivers/gpu/drm/i915/display/intel_hdmi.h | 7 +
>> 2 files changed, 188 insertions(+)
>>
>> diff --git a/drivers/gpu/drm/i915/display/intel_hdmi.c
>> b/drivers/gpu/drm/i915/display/intel_hdmi.c
>> index f90838bc74fb..6b9b9ea7f9b0 100644
>> --- a/drivers/gpu/drm/i915/display/intel_hdmi.c
>> +++ b/drivers/gpu/drm/i915/display/intel_hdmi.c
>> @@ -3438,3 +3438,184 @@ void intel_hdmi_init(struct drm_i915_private
>> *dev_priv,
>> dig_port->aux_ch = intel_bios_port_aux_ch(dev_priv, port);
>> intel_hdmi_init_connector(dig_port, intel_connector); }
>> +
>> +int intel_hdmi_dsc_get_slice_height(int vactive) {
>> + int slice_height;
>> +
>> + /*
>> + * Slice Height determination : HDMI2.1 Section 7.7.5.2
>> + * Select smallest slice height >=96, that results in a valid PPS and
>> + * requires minimum padding lines required for final slice.
>> + *
>> + * Assumption : Vactive is even.
>> + */
>> + for (slice_height = 96; slice_height <= vactive; slice_height += 2)
>> + if (vactive % slice_height == 0)
>> + return slice_height;
>> +
>> + return 0;
>> +}
>> +
>> +int
>> +intel_hdmi_dsc_get_num_slices(const struct intel_crtc_state *crtc_state,
>> + int src_max_slices, int src_max_slice_width,
>> + int hdmi_max_slices, int hdmi_throughput) {
> It would be good to add a comment describing each of the function parameters, this
> will make following code easier.
Alright, I will add documentation here.
>
>> +/* Pixel rates in KPixels/sec */
>> +#define HDMI_DSC_PEAK_PIXEL_RATE 2720000
>> +#define HDMI_DSC_MAX_ENC_THROUGHPUT_0 340000
>> +#define HDMI_DSC_MAX_ENC_THROUGHPUT_1 400000
> It would be good to add a comment to describe what actually this represent.
Agreed will have a comment to describe these macros.
>
>> +#define MAX_HDMI_SLICE_WIDTH 2720
> How this limit is defined, may be mention of the spec details.
Agreed, will provide details in next patch version.
>
>> + int kslice_adjust;
>> + int adjusted_clk_khz;
>> + int min_slices;
>> + int target_slices;
>> + int max_throughput; /* max clock freq. in khz per slice */
>> + int max_slice_width;
>> + int slice_width;
>> + int pixel_clock = crtc_state->hw.adjusted_mode.crtc_clock;
>> +
>> + if (!hdmi_throughput)
>> + return 0;
>> +
>> + /*
>> + * Slice Width determination : HDMI2.1 Section 7.7.5.1
>> + * kslice_adjust factor for 4:2:0 formats is 0.5, where as
>> + * for 4:4:4 is 1.0. Multiplying these factors by 10 and later
>> + * dividing adjusted clock value by 10.
>> + */
>> + if (crtc_state->output_format == INTEL_OUTPUT_FORMAT_YCBCR420)
>> + kslice_adjust = 5;
>> + else
>> + kslice_adjust = 10;
> May be add a note for 422 formats, or fail in that case, not sure if value of 1 holds
> good for 422 as well. If it's 1, then ignore the comment.
You are right, for 422 format correct value is 0.5.
I will set the value of 1 for 444 formats and the else case for 422 and
420 will be then 0.5
>
>> +
>> + adjusted_clk_khz = DIV_ROUND_UP(kslice_adjust * pixel_clock, 10);
>> +
>> + if (adjusted_clk_khz <= HDMI_DSC_PEAK_PIXEL_RATE)
>> + max_throughput = HDMI_DSC_MAX_ENC_THROUGHPUT_0;
>> + else
>> + max_throughput = HDMI_DSC_MAX_ENC_THROUGHPUT_1;
> A comment describing slight details will be good.
Will add the comments in this part in next version.
>
>> + /*
>> + * Taking into account the sink's capability for maximum
>> + * clock per slice (in MHz) as read from HF-VSDB.
>> + */
>> + max_throughput = min(max_throughput, hdmi_throughput * 1000);
>> +
>> + if (!max_throughput)
>> + return 0;
> hdmi_throughput is already checked for 0, so this is not needed.
Agreed, this is redundant, will get rid of this condition.
>> + min_slices = DIV_ROUND_UP(adjusted_clk_khz, max_throughput);
>> + max_slice_width = min(MAX_HDMI_SLICE_WIDTH, src_max_slice_width);
>> +
>> + /*
>> + * Keep on increasing the num of slices/line, starting from min_slices
>> + * per line till we get such a number, for which the slice_width is
>> + * just less than max_slice_width. The slices/line selected should be
>> + * less than or equal to the max horizontal slices that the combination
>> + * of PCON encoder and HDMI decoder can support.
>> + */
>> + slice_width = max_slice_width;
>> +
>> + do {
>> + if (min_slices <= 1 && src_max_slices >= 1 && hdmi_max_slices
>>> = 1)
>> + target_slices = 1;
>> + else if (min_slices <= 2 && src_max_slices >= 2 &&
>> hdmi_max_slices >= 2)
>> + target_slices = 2;
>> + else if (min_slices <= 4 && src_max_slices >= 4 &&
>> hdmi_max_slices >= 4)
>> + target_slices = 4;
>> + else if (min_slices <= 8 && src_max_slices >= 8 &&
>> hdmi_max_slices >= 8)
>> + target_slices = 8;
>> + else if (min_slices <= 12 && src_max_slices >= 12 &&
>> hdmi_max_slices >= 12)
>> + target_slices = 12;
>> + else if (min_slices <= 16 && src_max_slices >= 16 &&
>> hdmi_max_slices >= 16)
>> + target_slices = 16;
>> + else
>> + return 0;
>> +
>> + slice_width = DIV_ROUND_UP(crtc_state-
>>> hw.adjusted_mode.hdisplay, target_slices);
>> + if (slice_width >= max_slice_width)
>> + min_slices = target_slices + 1;
>> + } while (slice_width >= max_slice_width);
>> +
>> + return target_slices;
>> +}
>> +
>> +int
>> +intel_hdmi_dsc_get_bpp(int src_fractional_bpp, int slice_width, int num_slices,
>> + int output_format, bool hdmi_all_bpp,
>> + int hdmi_max_chunk_bytes)
> Describe the parameters here as well.
Will add the documentation for the function in next version.
>
>> +{
>> + int max_dsc_bpp, min_dsc_bpp;
>> + int target_bytes;
>> + bool bpp_found = false;
>> + int bpp_decrement_x16;
>> + int bpp_target;
>> + int bpp_target_x16;
>> +
>> + /*
>> + * Get min bpp and max bpp as per Table 7.23, in HDMI2.1 spec
>> + * Start with the max bpp and keep on decrementing with
>> + * fractional bpp, if supported by PCON DSC encoder
>> + *
>> + * for each bpp we check if no of bytes can be supported by HDMI sink
>> + */
>> +
>> + /* Assuming: bpc as 8*/
>> + if (output_format == INTEL_OUTPUT_FORMAT_YCBCR420) {
>> + min_dsc_bpp = 6;
>> + max_dsc_bpp = 3 * 4; /* 3*bpc/2 */
>> + } else {
>> + min_dsc_bpp = 8;
>> + max_dsc_bpp = 3 * 8; /* 3*bpc */
>> + }
> May be add a note for 422 formats, or fail in that case. I guess 8 and 24 will work
> for RGB and 422 will have different values. Please check and fix this.
Alright, will have a separate condition for 444 format and 420 format.
The 422 format will be then in else case.
>
>> +
>> + /*
>> + * Taking into account if all dsc_all_bpp supported by HDMI2.1 sink
>> + * Section 7.7.34 : Source shall not enable compressed Video
>> + * Transport with bpp_target settings above 12 bpp unless
>> + * DSC_all_bpp is set to 1.
>> + */
>> + if (!hdmi_all_bpp)
>> + max_dsc_bpp = min(max_dsc_bpp, 12);
>> +
>> + /*
>> + * The Sink has a limit of compressed data in bytes for a scanline,
>> + * as described in max_chunk_bytes field in HFVSDB block of edid.
>> + * The no. of bytes depend on the target bits per pixel that the
>> + * source configures. So we start with the max_bpp and calculate
>> + * the target_chunk_bytes. We keep on decrementing the target_bpp,
>> + * till we get the target_chunk_bytes just less than what the sink's
>> + * max_chunk_bytes, or else till we reach the min_dsc_bpp.
>> + *
>> + * The decrement is according to the fractional support from PCON DSC
>> + * encoder. For fractional BPP we use bpp_target as a multiple of 16.
>> + *
>> + * bpp_target_x16 = bpp_target * 16
>> + * So we need to decrement by {1, 2, 4, 8, 16} for fractional bpps
>> + * {1/16, 1/8, 1/4, 1/2, 1} respectively.
>> + */
>> +
>> + bpp_target = max_dsc_bpp;
>> + if (src_fractional_bpp)
> I think you missed a ! here
Thanks for catching that. Will fix in the next version.
>
>> + return 0;
>> + bpp_decrement_x16 = DIV_ROUND_UP(16, src_fractional_bpp);
>> + bpp_target_x16 = (bpp_target * 16) - bpp_decrement_x16;
>> +
>> + while (bpp_target_x16 > (min_dsc_bpp * 16)) {
>> + int bpp;
>> +
>> + bpp = DIV_ROUND_UP(bpp_target_x16, 16);
>> + target_bytes = num_slices * slice_width * DIV_ROUND_UP(bpp,
>> 8);
>> + if (target_bytes <= hdmi_max_chunk_bytes) {
>> + bpp_found = true;
>> + break;
>> + }
>> + bpp_target_x16 -= bpp_decrement_x16;
> Not sure on the overall calculation on this part, but if this works then I am good. Please confirm the
> same with actual bpp values computed and validate.
The value for bpp was seen to be around 10-12bpp for with TGL platform
with for 8k resolutions with one of the DSC1.2 panel for 8k modes.
>> + }
>> + if (bpp_found)
>> + return bpp_target_x16;
> I think we should divide by 16 and return. Isn't it ?
The values expected to be written in PPS parameter register are x16 so I
am directly returning this value.
Thanks & Regards,
Ankit
>> +
>> + return 0;
>> +}
>> diff --git a/drivers/gpu/drm/i915/display/intel_hdmi.h
>> b/drivers/gpu/drm/i915/display/intel_hdmi.h
>> index 15eb0ccde76e..fa1a9b030850 100644
>> --- a/drivers/gpu/drm/i915/display/intel_hdmi.h
>> +++ b/drivers/gpu/drm/i915/display/intel_hdmi.h
>> @@ -50,5 +50,12 @@ bool intel_hdmi_limited_color_range(const struct
>> intel_crtc_state *crtc_state,
>> const struct drm_connector_state
>> *conn_state); bool intel_hdmi_deep_color_possible(const struct intel_crtc_state
>> *crtc_state, int bpc,
>> bool has_hdmi_sink, bool ycbcr420_output);
>> +int intel_hdmi_dsc_get_bpp(int src_fractional_bpp, int slice_width,
>> + int num_slices, int output_format, bool hdmi_all_bpp,
>> + int hdmi_max_chunk_bytes);
>> +int intel_hdmi_dsc_get_num_slices(const struct intel_crtc_state *crtc_state,
>> + int src_max_slices, int src_max_slice_width,
>> + int hdmi_max_slices, int hdmi_throughput); int
>> +intel_hdmi_dsc_get_slice_height(int vactive);
>>
>> #endif /* __INTEL_HDMI_H__ */
>> --
>> 2.17.1
More information about the Intel-gfx
mailing list