[Intel-gfx] [PATCH 1/2] drm/i915/hdcp: Fix 1B-06 HDCP2.2 Comp test

[Anshuman Gupta]

On 2020-02-06 at 23:06:57 +0530, Ramalingam C wrote:
> On 2020-02-06 at 22:39:28 +0530, Anshuman Gupta wrote:
> > On 2020-02-06 at 22:30:27 +0530, Ramalingam C wrote:
> > > On 2020-02-06 at 20:34:41 +0530, Anshuman Gupta wrote:
> > > > HDCP Repeater initializes seq_num_V to 0 at the beginning of
> > > > hdcp Session i.e. after AKE_init received.
> > > > 
> > > > HDCP 2.2 Comp specs 1B-06 test verifies that whether DUT
> > > > considers failures of authentication if the repeater provides a
> > > > non-zero value in seq_num_V in the first,
> > > > RepeaterAuth_Send_ReceiverID_List message after first AKE_Init.
> > > > Fixing this broken test.
> > > Instead of "Fixing the broken test" could we say, we mandate the first
> > > seq_num_v to be zero? in fact i would keep this as commit subject also. 
> > > > 
> > > > Cc: Ramalingam C <ramalingam.c at intel.com>
> > > > Signed-off-by: Anshuman Gupta <anshuman.gupta at intel.com>
> > > > ---
> > > >  drivers/gpu/drm/i915/display/intel_display_types.h |  3 +++
> > > >  drivers/gpu/drm/i915/display/intel_hdcp.c          | 13 +++++++++++++
> > > >  2 files changed, 16 insertions(+)
> > > > 
> > > > diff --git a/drivers/gpu/drm/i915/display/intel_display_types.h b/drivers/gpu/drm/i915/display/intel_display_types.h
> > > > index 7ae0bc8b80d1..2ae540e986ba 100644
> > > > --- a/drivers/gpu/drm/i915/display/intel_display_types.h
> > > > +++ b/drivers/gpu/drm/i915/display/intel_display_types.h
> > > > @@ -360,6 +360,9 @@ struct intel_hdcp {
> > > >  	/* HDCP2.2 Encryption status */
> > > >  	bool hdcp2_encrypted;
> > > >  
> > > > +	/* Flag indicate if it is a first ReceiverID_List msg after AKE_Init */
> > > > +	bool first_recvid_msg;
> > > This extra flag is not needed, see below comment
> > > > +
> > > >  	/*
> > > >  	 * Content Stream Type defined by content owner. TYPE0(0x0) content can
> > > >  	 * flow in the link protected by HDCP2.2 or HDCP1.4, where as TYPE1(0x1)
> > > > diff --git a/drivers/gpu/drm/i915/display/intel_hdcp.c b/drivers/gpu/drm/i915/display/intel_hdcp.c
> > > > index 4d1a33d13105..3e24a6df503a 100644
> > > > --- a/drivers/gpu/drm/i915/display/intel_hdcp.c
> > > > +++ b/drivers/gpu/drm/i915/display/intel_hdcp.c
> > > > @@ -1251,6 +1251,8 @@ static int hdcp2_authentication_key_exchange(struct intel_connector *connector)
> > > >  	size_t size;
> > > >  	int ret;
> > > >  
> > > > +	hdcp->first_recvid_msg = true;
> > > > +
> > > >  	/* Init for seq_num */
> > > >  	hdcp->seq_num_v = 0;
> > > >  	hdcp->seq_num_m = 0;
> > > > @@ -1462,6 +1464,16 @@ int hdcp2_authenticate_repeater_topology(struct intel_connector *connector)
> > > >  	seq_num_v =
> > > >  		drm_hdcp_be24_to_cpu((const u8 *)msgs.recvid_list.seq_num_v);
> > > >  
> > > > +	/*
> > > > +	 * HDCP 2.2 Spec HDMI PAGE 19, DP PAGE 20
> > > > +	 * HDCP 2.2 Comp 1B-06 test requires to disable encryption if there is
> > > > +	 * non zero seq_num_V from recevier.
> > > IMHO In commit message this kind of reasoning make sense, but here this is
> > > not needed. As every line in the file will be as per the spec so we dont
> > > need to call them out.
> > > > +	 */
> > > > +	if (hdcp->first_recvid_msg && seq_num_v) {
> > > if (!hdcp->seq_num_v && seq_num_v) {
> > > 
> > > IMO This is all we need it.
> > I had tried this as my first solution, eventually this fill the link integrity check, see below.
> > > 
> > > -Ram
> > > > +		drm_dbg_kms(&dev_priv->drm, "Non zero Seq_num_v at beginning of HDCP Session\n");
> > > > +		return -EINVAL;
> > > > +	}
> > > > +
> > > >  	if (seq_num_v < hdcp->seq_num_v) {
> > > >  		/* Roll over of the seq_num_v from repeater. Reauthenticate. */
> > > >  		DRM_DEBUG_KMS("Seq_num_v roll over.\n");
> > > > @@ -1484,6 +1496,7 @@ int hdcp2_authenticate_repeater_topology(struct intel_connector *connector)
> > > >  		return ret;
> > > >  
> > > >  	hdcp->seq_num_v = seq_num_v;
> > 	seq_num_v will be zero for first session, which left hdcp->seq_num_v to zero and that will
> > 	fail the link intergrity check as at during link intergrity check seq_num_v will be non-zero,
> >         this happens during 1B-09, when repeater topolgy changes due to Roll over of seq_num_v.
> 
> topology update should increment the seq_num_v which will make it > than
> hdcp->seq_num_v. How roll over happens? And at every AKE start we init
> hdcp->seq_num_v to 0.
> 
> So please elaborate the failure scenario.
Please refer to HDCP 2.2 spec page page 44 Step 1-B-09
STEP 1B-09-01
-> TE sets seq_num_V to 0xFFFFFFh
-> TE simulate disconnect of active downstream device by decrementing DEVICE_COUNT
*As I understand above will assert the READY bit that will detect as topology change and will make a call 
 to hdcp2_authenticate_repeater_topology() and there it will fail for 
 if (!hdcp->seq_num_v && seq_num_v) conidiation, and test will fail here itself.
-> DUT sends RepeaterAuth_Send_Ack message
STEP 1B-09-02
-> TE will set seq_num_V to 0x000 to indicate Roll Over.

Please correct me if i am wrong here.

Thanks ,
Anshuman Gupta.

> 
> Ram.
> > Thanks ,
> > Anshuman Gupta.
> > 
> > > > +	hdcp->first_recvid_msg = false;
> > > >  	ret = shim->write_2_2_msg(intel_dig_port, &msgs.rep_ack,
> > > >  				  sizeof(msgs.rep_ack));
> > > >  	if (ret < 0)
> > > > -- 
> > > > 2.24.0
> > > >