[Intel-gfx] [PATCH] drm/i915/dp: Add current maximum eDP link rate to sink_rate array.

[Mario Kleiner]

If the current eDP link rate, as read from hw, provides a
higher bandwidth than the standard link rates, then add the
current link rate to the link_rates array for consideration
in future mode-sets.

These initial current eDP link settings have been set up by
firmware during boot, so they should work on the eDP panel.
Therefore use them if the firmware thinks they are good and
they provide higher link bandwidth, e.g., to enable higher
resolutions / color depths.

This fixes a problem found on the MacBookPro 2017 Retina panel:

The panel reports 10 bpc color depth in its EDID, and the UEFI
firmware chooses link settings at boot which support enough
bandwidth for 10 bpc (324000 kbit/sec to be precise), but the
DP_MAX_LINK_RATE dpcd register only reports 2.7 Gbps as possible,
so intel_dp_set_sink_rates() would cap at that. This restricts
achievable color depth to 8 bpc, not providing the full color
depth of the panel. With this commit, we can use firmware setting
and get the full 10 bpc advertised by the Retina panel.

Signed-off-by: Mario Kleiner <mario.kleiner.de at gmail.com>
Cc: Daniel Vetter <daniel.vetter at ffwll.ch>
---
 drivers/gpu/drm/i915/display/intel_dp.c | 23 +++++++++++++++++++++++
 1 file changed, 23 insertions(+)

diff --git a/drivers/gpu/drm/i915/display/intel_dp.c b/drivers/gpu/drm/i915/display/intel_dp.c
index 2f31d226c6eb..aa3e0b5108c6 100644
--- a/drivers/gpu/drm/i915/display/intel_dp.c
+++ b/drivers/gpu/drm/i915/display/intel_dp.c
@@ -4368,6 +4368,8 @@ intel_edp_init_dpcd(struct intel_dp *intel_dp)
 {
 	struct drm_i915_private *dev_priv =
 		to_i915(dp_to_dig_port(intel_dp)->base.base.dev);
+	int max_rate;
+	u8 link_bw;
 
 	/* this function is meant to be called only once */
 	WARN_ON(intel_dp->dpcd[DP_DPCD_REV] != 0);
@@ -4433,6 +4435,27 @@ intel_edp_init_dpcd(struct intel_dp *intel_dp)
 	else
 		intel_dp_set_sink_rates(intel_dp);
 
+	/*
+	 * If the firmware programmed a rate higher than the standard sink rates
+	 * during boot, then add that rate as a valid sink rate, as fw knows
+	 * this is a good rate and we get extra bandwidth.
+	 *
+	 * Helps, e.g., on the Apple MacBookPro 2017 Retina panel, which is only
+	 * eDP 1.1, but supports the unusual rate of 324000 kHz at bootup, for
+	 * 10 bpc / 30 bit color depth.
+	 */
+	if (!intel_dp->use_rate_select &&
+	    (drm_dp_dpcd_read(&intel_dp->aux, DP_LINK_BW_SET, &link_bw, 1) == 1) &&
+	    (link_bw > 0) && (intel_dp->num_sink_rates < DP_MAX_SUPPORTED_RATES)) {
+		max_rate = drm_dp_bw_code_to_link_rate(link_bw);
+		if (max_rate > intel_dp->sink_rates[intel_dp->num_sink_rates - 1]) {
+			intel_dp->sink_rates[intel_dp->num_sink_rates] = max_rate;
+			intel_dp->num_sink_rates++;
+			DRM_DEBUG_KMS("Adding max bandwidth eDP rate %d kHz.\n",
+				      max_rate);
+		}
+	}
+
 	intel_dp_set_common_rates(intel_dp);
 
 	/* Read the eDP DSC DPCD registers */
-- 
2.24.0