[Intel-gfx] [V8 7/9] drm/i915/dsi: Add TE handler for dsi cmd mode.

[Jani Nikula]

On Thu, 12 Mar 2020, Vandita Kulkarni <vandita.kulkarni at intel.com> wrote:
> In case of dual link, we get the TE on slave.
> So clear the TE on slave DSI IIR.
>
> v2: Pass only relevant masked bits to the handler (Jani)
>
> v3: Fix the check for cmd mode in TE handler function.
>
> Signed-off-by: Vandita Kulkarni <vandita.kulkarni at intel.com>
> ---
>  drivers/gpu/drm/i915/i915_irq.c | 64 +++++++++++++++++++++++++++++++++
>  1 file changed, 64 insertions(+)
>
> diff --git a/drivers/gpu/drm/i915/i915_irq.c b/drivers/gpu/drm/i915/i915_irq.c
> index 89489a247276..2e1418515c9f 100644
> --- a/drivers/gpu/drm/i915/i915_irq.c
> +++ b/drivers/gpu/drm/i915/i915_irq.c
> @@ -2262,6 +2262,62 @@ gen8_de_misc_irq_handler(struct drm_i915_private *dev_priv, u32 iir)
>  		drm_err(&dev_priv->drm, "Unexpected DE Misc interrupt\n");
>  }
>  
> +void gen11_dsi_te_interrupt_handler(struct drm_i915_private *dev_priv,
> +				    u32 te_trigger)
> +{
> +	enum pipe pipe = INVALID_PIPE;
> +	enum transcoder dsi_trans;
> +	enum port port;
> +	u32 val, tmp;
> +
> +	/*
> +	 * Incase of dual link, TE comes from DSI_1
> +	 * this is to check if dual link is enabled
> +	 */
> +	val = I915_READ(TRANS_DDI_FUNC_CTL2(TRANSCODER_DSI_0));
> +	val &= PORT_SYNC_MODE_ENABLE;
> +
> +	/*
> +	 * if dual link is enabled, then read DSI_0
> +	 * transcoder registers
> +	 */
> +	port = ((te_trigger & DSI1_TE && val) || (te_trigger & DSI0_TE)) ?
> +						  PORT_A : PORT_B;
> +	dsi_trans = (port == PORT_A) ? TRANSCODER_DSI_0 : TRANSCODER_DSI_1;
> +
> +	/* Check if DSI configured in command mode */
> +	val = I915_READ(DSI_TRANS_FUNC_CONF(dsi_trans));
> +	val = val & OP_MODE_MASK;
> +
> +	if ((val != CMD_MODE_NO_GATE) && (val != CMD_MODE_TE_GATE)) {
> +		DRM_ERROR("DSI trancoder not configured in command mode\n");

drm_err()

> +		return;
> +	}
> +
> +	/* Get PIPE for handling VBLANK event */
> +	val = I915_READ(TRANS_DDI_FUNC_CTL(dsi_trans));
> +	switch (val & TRANS_DDI_EDP_INPUT_MASK) {
> +	case TRANS_DDI_EDP_INPUT_A_ON:
> +		pipe = PIPE_A;
> +		break;
> +	case TRANS_DDI_EDP_INPUT_B_ONOFF:
> +		pipe = PIPE_B;
> +		break;
> +	case TRANS_DDI_EDP_INPUT_C_ONOFF:
> +		pipe = PIPE_C;
> +		break;
> +	default:
> +		DRM_ERROR("Invalid PIPE\n");

drm_err()... but don't want to pass INVALID_PIPE to
intel_handle_vblank() below.

> +	}
> +
> +	/* clear TE in dsi IIR */
> +	port = (te_trigger & DSI1_TE) ? PORT_B : PORT_A;
> +	tmp = I915_READ(DSI_INTR_IDENT_REG(port));
> +	I915_WRITE(DSI_INTR_IDENT_REG(port), tmp);
> +
> +	drm_handle_vblank(&dev_priv->drm, pipe);

Please use intel_handle_vblank(). It takes into account pipe might not
match crtc index.

> +}
> +
>  static irqreturn_t
>  gen8_de_irq_handler(struct drm_i915_private *dev_priv, u32 master_ctl)
>  {
> @@ -2328,6 +2384,14 @@ gen8_de_irq_handler(struct drm_i915_private *dev_priv, u32 master_ctl)
>  				found = true;
>  			}
>  
> +			if (INTEL_GEN(dev_priv) >= 11) {
> +				tmp_mask = iir & (DSI0_TE | DSI1_TE);
> +				if (tmp_mask) {
> +					gen11_dsi_te_interrupt_handler(dev_priv, tmp_mask);
> +					found = true;
> +				}
> +			}
> +
>  			if (!found)
>  				drm_err(&dev_priv->drm,
>  					"Unexpected DE Port interrupt\n");

-- 
Jani Nikula, Intel Open Source Graphics Center