[Intel-gfx] [PATCH v3 6/7] drm/i915/display: Reduce blanking to support 4k60 at 10bpp for LSPCON

[Vipin Anand]

From: Uma Shankar <uma.shankar at intel.com>

Blanking needs to be reduced to incorporate DP and HDMI timing/link
bandwidth limitations for CEA modes (4k at 60 at 10 bpp). DP can drive
17.28Gbs while 4k modes (VIC97 etc) at 10 bpp required 17.8 Gbps.
This will cause mode to blank out. Reduced Htotal by shortening the
back porch and front porch within permissible limits.

v2: This is marked as Not for merge and the responsibilty to program
these custom timings will be on userspace. This patch is just for
reference purposes. This is based on Ville's recommendation.

Signed-off-by: Uma Shankar <uma.shankar at intel.com>
Signed-off-by: Vipin Anand <vipin.anand at intel.com>
---
 drivers/gpu/drm/i915/display/intel_dp.c | 16 ++++++++++++++++
 1 file changed, 16 insertions(+)

diff --git a/drivers/gpu/drm/i915/display/intel_dp.c b/drivers/gpu/drm/i915/display/intel_dp.c
index c7424e2a04a3..3ab1fadb2ea3 100644
--- a/drivers/gpu/drm/i915/display/intel_dp.c
+++ b/drivers/gpu/drm/i915/display/intel_dp.c
@@ -616,9 +616,11 @@ intel_dp_mode_valid(struct drm_connector *connector,
 {
 	struct intel_dp *intel_dp = intel_attached_dp(to_intel_connector(connector));
 	struct intel_connector *intel_connector = to_intel_connector(connector);
+	struct intel_encoder *intel_encoder = intel_attached_encoder(intel_connector);
 	struct drm_display_mode *fixed_mode = intel_connector->panel.fixed_mode;
 	struct drm_i915_private *dev_priv = to_i915(connector->dev);
 	int target_clock = mode->clock;
+	struct intel_lspcon *lspcon = enc_to_intel_lspcon(intel_encoder);
 	int max_rate, mode_rate, max_lanes, max_link_clock;
 	int max_dotclk;
 	u16 dsc_max_output_bpp = 0;
@@ -638,6 +640,20 @@ intel_dp_mode_valid(struct drm_connector *connector,
 
 		target_clock = fixed_mode->clock;
 	}
+	/*
+	 * Reducing Blanking to incorporate DP and HDMI timing/link bandwidth
+	 * limitations for CEA modes (4k at 60 at 10 bpp). DP can drive 17.28Gbs
+	 * while 4k modes (VIC97 etc) at 10 bpp required 17.8 Gbps. This will
+	 * cause mode to blank out. Reduced Htotal by shortening the back porch
+	 * and front porch within permissible limits.
+	 */
+	if (lspcon->active && lspcon->hdr_supported &&
+	    mode->clock > 570000) {
+		mode->clock = 570000;
+		mode->htotal -= 180;
+		mode->hsync_start -= 72;
+		mode->hsync_end -= 72;
+	}
 
 	max_link_clock = intel_dp_max_link_rate(intel_dp);
 	max_lanes = intel_dp_max_lane_count(intel_dp);
-- 
2.26.0