[Intel-gfx] [PATCH v2 13/13] drm/i915: Configure PCON for DSC1.1 to DSC1.2 encoding

Shankar, Uma uma.shankar at intel.com
Wed Nov 25 20:45:05 UTC 2020



> -----Original Message-----
> From: Nautiyal, Ankit K <ankit.k.nautiyal at intel.com>
> Sent: Sunday, November 1, 2020 3:37 PM
> To: intel-gfx at lists.freedesktop.org
> Cc: dri-devel at lists.freedesktop.org; Shankar, Uma <uma.shankar at intel.com>;
> Kulkarni, Vandita <vandita.kulkarni at intel.com>; ville.syrjala at linux.intel.com;
> Sharma, Swati2 <swati2.sharma at intel.com>
> Subject: [PATCH v2 13/13] drm/i915: Configure PCON for DSC1.1 to DSC1.2
> encoding

May be good to append i915/ with display as well.

> When a source supporting DSC1.1 is connected to DSC1.2 HDMI2.1 sink via DP
> HDMI2.1 PCON, the PCON can be configured to decode the
> DSC1.1 compressed stream and encode to DSC1.2. It then sends the
> DSC1.2 compressed stream to the HDMI2.1 sink.
> 
> This patch configures the PCON for DSC1.1 to DSC1.2 encoding, based on the
> PCON's DSC encoder capablities and HDMI2.1 sink's DSC decoder capabilities.
> 
> v2: Rebase
> 
> Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal at intel.com>
> ---
>  drivers/gpu/drm/i915/display/intel_ddi.c |   1 +
>  drivers/gpu/drm/i915/display/intel_dp.c  | 128 ++++++++++++++++++++++-
>  drivers/gpu/drm/i915/display/intel_dp.h  |   2 +
>  3 files changed, 129 insertions(+), 2 deletions(-)
> 
> diff --git a/drivers/gpu/drm/i915/display/intel_ddi.c
> b/drivers/gpu/drm/i915/display/intel_ddi.c
> index 3e76fb1117df..dbf28d021d08 100644
> --- a/drivers/gpu/drm/i915/display/intel_ddi.c
> +++ b/drivers/gpu/drm/i915/display/intel_ddi.c
> @@ -3493,6 +3493,7 @@ static void tgl_ddi_pre_enable_dp(struct
> intel_atomic_state *state,
>  	intel_dp_sink_set_fec_ready(intel_dp, crtc_state);
> 
>  	intel_dp_check_frl_training(intel_dp);
> +	intel_dp_pcon_dsc_configure(intel_dp, crtc_state);

These are called here unconditionally, I think we should invoke them only if
we are driving a pcon and not a native DP.

> 
>  	/*
>  	 * 7.i Follow DisplayPort specification training sequence (see notes for
> diff --git a/drivers/gpu/drm/i915/display/intel_dp.c
> b/drivers/gpu/drm/i915/display/intel_dp.c
> index 2e7ddb062efe..bc1f1afc35ad 100644
> --- a/drivers/gpu/drm/i915/display/intel_dp.c
> +++ b/drivers/gpu/drm/i915/display/intel_dp.c
> @@ -788,6 +788,16 @@ intel_dp_mode_valid(struct drm_connector *connector,
>  							     target_clock,
>  							     mode->hdisplay);
>  		}
> +
> +		/*
> +		 * TODO: If its a PCON with HDMI sink:
> +		 * Assumption : Source only supports DSC1.1
> +		 *
> +		 * If HDMI supports DSC 1.2 but PCON does not support
> +		 * DSC1.1->DSC1.2 encoding Then return MODE_CLOCK_HIGH.
> +		 * Otherwise check if the mode can be applied according to
> +		 * DSC capablities of the PCON and HDMI Sink combine.
> +		 */
>  	}
> 
>  	if ((mode_rate > max_rate && !(dsc_max_output_bpp &&
> dsc_slice_count)) || @@ -3936,9 +3946,21 @@ static int
> intel_dp_hdmi_sink_max_frl(struct intel_dp *intel_dp)  {
>  	struct intel_connector *intel_connector = intel_dp->attached_connector;
>  	struct drm_connector *connector = &intel_connector->base;
> +	int max_frl_rate;
> +	int max_lanes, rate_per_lane;
> +	int max_dsc_lanes, dsc_rate_per_lane;
> +
> +	max_lanes = connector->display_info.hdmi.max_lanes;
> +	rate_per_lane = connector->display_info.hdmi.max_frl_rate_per_lane;
> +	max_frl_rate = max_lanes * rate_per_lane;
> +
> +	if (connector->display_info.hdmi.dsc_cap.v_1p2) {
> +		max_dsc_lanes = connector-
> >display_info.hdmi.dsc_cap.max_lanes;
> +		dsc_rate_per_lane = connector-
> >display_info.hdmi.dsc_cap.max_frl_rate_per_lane;
> +		max_frl_rate = min(max_frl_rate, max_dsc_lanes *
> dsc_rate_per_lane);
> +	}
> 
> -	return (connector->display_info.hdmi.max_frl_rate_per_lane *
> -		connector->display_info.hdmi.max_lanes);
> +	return max_frl_rate;
>  }
> 
>  static int intel_dp_pcon_start_frl_training(struct intel_dp *intel_dp) @@ -
> 4071,6 +4093,106 @@ void intel_dp_check_frl_training(struct intel_dp *intel_dp)
>  	}
>  }
> 
> +static int
> +intel_dp_pcon_dsc_enc_slice_height(const struct intel_crtc_state
> +*crtc_state) {
> +
> +	int vactive = crtc_state->hw.adjusted_mode.vdisplay;
> +
> +	return intel_hdmi_dsc_get_slice_height(vactive);
> +}
> +
> +static int
> +intel_dp_pcon_dsc_enc_slices(struct intel_dp *intel_dp,
> +			     const struct intel_crtc_state *crtc_state) {
> +	struct intel_connector *intel_connector = intel_dp->attached_connector;
> +	struct drm_connector *connector = &intel_connector->base;
> +	int hdmi_throughput = connector-
> >display_info.hdmi.dsc_cap.clk_per_slice;
> +	int hdmi_max_slices = connector->display_info.hdmi.dsc_cap.max_slices;
> +	int pcon_max_slices = drm_dp_pcon_dsc_max_slices(intel_dp-
> >pcon_dsc_dpcd);
> +	int pcon_max_slice_width =
> +drm_dp_pcon_dsc_max_slice_width(intel_dp->pcon_dsc_dpcd);
> +
> +
> +	return intel_hdmi_dsc_get_num_slices(crtc_state, pcon_max_slices,
> +					     pcon_max_slice_width,
> +					     hdmi_max_slices, hdmi_throughput); }
> +
> +static int
> +intel_dp_pcon_dsc_enc_bpp(struct intel_dp *intel_dp,
> +			  const struct intel_crtc_state *crtc_state,
> +			  int num_slices, int slice_width)
> +{
> +	struct intel_connector *intel_connector = intel_dp->attached_connector;
> +	struct drm_connector *connector = &intel_connector->base;
> +	int output_format = crtc_state->output_format;
> +	bool hdmi_all_bpp = connector->display_info.hdmi.dsc_cap.all_bpp;
> +	int pcon_fractional_bpp = drm_dp_pcon_dsc_bpp_incr(intel_dp-
> >pcon_dsc_dpcd);
> +	int hdmi_max_chunk_bytes =
> +		connector->display_info.hdmi.dsc_cap.total_chunk_kbytes *
> 1024;
> +
> +	return intel_hdmi_dsc_get_bpp(pcon_fractional_bpp, slice_width,
> +				      num_slices, output_format, hdmi_all_bpp,
> +				      hdmi_max_chunk_bytes);
> +}
> +
> +void
> +intel_dp_pcon_dsc_configure(struct intel_dp *intel_dp,
> +			    const struct intel_crtc_state *crtc_state) {
> +	u8 pps_param[6];
> +	u8 buf;
> +	int version_major, version_minor;
> +	int slice_height;
> +	int slice_width;
> +	int num_slices;
> +	int bits_per_pixel;
> +	int ret;
> +	struct intel_connector *intel_connector = intel_dp->attached_connector;
> +	struct drm_i915_private *i915 = dp_to_i915(intel_dp);
> +	struct drm_connector *connector = &intel_connector->base;
> +	bool hdmi_is_dsc_1_2 = connector->display_info.hdmi.dsc_cap.v_1p2;

This may be NULL, please add a check before using it.

> +
> +
> +	buf = intel_dp->pcon_dsc_dpcd[DP_PCON_DSC_VERSION -
> DP_PCON_DSC_ENCODER];
> +	version_major = (buf & DP_PCON_DSC_MAJOR_MASK) >>
> DP_PCON_DSC_MAJOR_SHIFT;
> +	version_minor = (buf & DP_PCON_DSC_MINOR_MASK) >>
> +DP_PCON_DSC_MINOR_SHIFT;
> +
> +
> +	/* Only if PCON encoder and HDMI decoder both support DSC 1.2 */
> +	if ((version_major != 1 || version_minor != 2) ||
> +	    (!hdmi_is_dsc_1_2))
> +		return;
> +
> +	slice_height = intel_dp_pcon_dsc_enc_slice_height(crtc_state);
> +	if (!slice_height)
> +		return;
> +
> +	num_slices = intel_dp_pcon_dsc_enc_slices(intel_dp, crtc_state);
> +	if (!num_slices)
> +		return;
> +
> +	slice_width = DIV_ROUND_UP(crtc_state->hw.adjusted_mode.hdisplay,
> +				   num_slices);
> +
> +	bits_per_pixel = intel_dp_pcon_dsc_enc_bpp(intel_dp, crtc_state,
> +						  num_slices, slice_width);
> +	if (!bits_per_pixel)
> +		return;
> +
> +	pps_param[0] = slice_height >> 8;
> +	pps_param[1] = slice_height & 0xFF;

First we have LSB, so isn't the order be reversed ?

> +	pps_param[2] = slice_width >> 8;
> +	pps_param[3] = slice_width & 0xFF;

Same here.

> +	pps_param[4] = bits_per_pixel >> 8;
> +	pps_param[5] = bits_per_pixel & 0xFF;

Last 2:7 are reserved, so adjust the mask accordingly.

> +
> +	ret = drm_dp_pcon_pps_override_param(&intel_dp->aux, pps_param);
> +	if (ret < 0)
> +		drm_dbg_kms(&i915->drm, "Failed to set pcon DSC\n"); }
> +
>  static void
>  g4x_set_link_train(struct intel_dp *intel_dp,
>  		   const struct intel_crtc_state *crtc_state, @@ -4202,6 +4324,7
> @@ static void intel_enable_dp(struct intel_atomic_state *state,
>  	intel_dp_set_power(intel_dp, DP_SET_POWER_D0);
>  	intel_dp_configure_protocol_converter(intel_dp);
>  	intel_dp_check_frl_training(intel_dp);
> +	intel_dp_pcon_dsc_configure(intel_dp, pipe_config);
>  	intel_dp_start_link_train(intel_dp, pipe_config);
>  	intel_dp_stop_link_train(intel_dp, pipe_config);
> 
> @@ -6149,6 +6272,7 @@ int intel_dp_retrain_link(struct intel_encoder
> *encoder,
>  			continue;
> 
>  		intel_dp_check_frl_training(intel_dp);
> +		intel_dp_pcon_dsc_configure(intel_dp, crtc_state);
>  		intel_dp_start_link_train(intel_dp, crtc_state);
>  		intel_dp_stop_link_train(intel_dp, crtc_state);
>  		break;
> diff --git a/drivers/gpu/drm/i915/display/intel_dp.h
> b/drivers/gpu/drm/i915/display/intel_dp.h
> index a667d3f578d6..3515e057447e 100644
> --- a/drivers/gpu/drm/i915/display/intel_dp.h
> +++ b/drivers/gpu/drm/i915/display/intel_dp.h
> @@ -144,5 +144,7 @@ void intel_dp_sync_state(struct intel_encoder *encoder,
>  			 const struct intel_crtc_state *crtc_state);
> 
>  void intel_dp_check_frl_training(struct intel_dp *intel_dp);
> +void intel_dp_pcon_dsc_configure(struct intel_dp *intel_dp,
> +				 const struct intel_crtc_state *crtc_state);
> 
>  #endif /* __INTEL_DP_H__ */
> --
> 2.17.1



More information about the Intel-gfx mailing list