[Intel-gfx] [PATCH] drm/i915/dsc: Fix the usage of uncompressed bpp
Kulkarni, Vandita
vandita.kulkarni at intel.com
Tue Nov 2 04:35:32 UTC 2021
> -----Original Message-----
> From: Navare, Manasi D <manasi.d.navare at intel.com>
> Sent: Tuesday, November 2, 2021 10:11 AM
> To: Kulkarni, Vandita <vandita.kulkarni at intel.com>
> Cc: intel-gfx at lists.freedesktop.org; Nikula, Jani <jani.nikula at intel.com>
> Subject: Re: [PATCH] drm/i915/dsc: Fix the usage of uncompressed bpp
>
> On Mon, Nov 01, 2021 at 09:45:23AM -0700, Kulkarni, Vandita wrote:
> > > -----Original Message-----
> > > From: Navare, Manasi D <manasi.d.navare at intel.com>
> > > Sent: Saturday, October 30, 2021 4:43 AM
> > > To: Kulkarni, Vandita <vandita.kulkarni at intel.com>
> > > Cc: intel-gfx at lists.freedesktop.org; Nikula, Jani
> > > <jani.nikula at intel.com>
> > > Subject: Re: [PATCH] drm/i915/dsc: Fix the usage of uncompressed bpp
> > >
> > > On Wed, Oct 27, 2021 at 09:37:10PM -0700, Kulkarni, Vandita wrote:
> > > > > -----Original Message-----
> > > > > From: Navare, Manasi D <manasi.d.navare at intel.com>
> > > > > Sent: Thursday, October 28, 2021 12:57 AM
> > > > > To: Kulkarni, Vandita <vandita.kulkarni at intel.com>
> > > > > Cc: intel-gfx at lists.freedesktop.org; Nikula, Jani
> > > > > <jani.nikula at intel.com>
> > > > > Subject: Re: [PATCH] drm/i915/dsc: Fix the usage of uncompressed
> > > > > bpp
> > > > >
> > > > > On Wed, Oct 27, 2021 at 03:23:16PM +0530, Vandita Kulkarni wrote:
> > > > > > DP 1.4 spec limits max compression bpp to uncompressed bpp -1,
> > > > > > which is supported from XELPD onwards.
> > > > > > Instead of uncompressed bpp, max dsc input bpp was being used
> > > > > > to limit the max compression bpp.
> > > > >
> > > > > So the input Pipe BPP which is the uncompressed bpp is decided
> > > > > by the input bpc and when this was initially written, we had
> > > > > designed it to respect the max_req_bpc by the user.
> > > > > So that is what we use to decide the input bpc and hence the
> > > > > pipe_bpp This input pipe_bpp decides the compressed bpp that we
> > > > > calculate based on all the supported output bpps which are
> > > > > supported all the way upto uncompressed_output_bpp - 1.
> > > > >
> > > > > So I dont see the need to change the logic here. Moreover I dont
> > > > > see any change in the dsc_compute_bpp function So I dont
> > > > > understand the purpose of introducing the new max_dsc_pipe_bpp
> > > > > variable here
> > > >
> > > > Thanks for the comments, I had few more opens around this along
> > > > with
> > > this patch.
> > > >
> > > > AFAIU about max_requested_bpc it is to limit the max_bpc
> > > > "drm: Add connector property to limit max bpc"
> > > > And the driver is supposed to program the default bpc as per the
> > > > connector
> > > limitation.
> > > > Which is 12 as per the current driver implementation.
> > > >
> > > > I had few queries around this design:
> > > > So it means that max_dsc_input_bpp would be set to 36 if supported
> > > > by the
> > > sink and the platform.
> > > > And now we make this as our pipe_bpp, 1. Does this mean that we
> > > > are assuming 12bpc as i/p always?
> > > > 2. What happens to those with formats 8bpc, 10 bpc?
> > > >
> > >
> > > Yes so this driver policy was decided based on some feedback that I
> > > had got from the community as well as internal feedback from Ville
> > > that the decision of input_bpc should be based on max_bpc requested
> > > by the user through the connector property and max_bpc supported by
> the platform.
> > > Here we take the min of the two so that we dont violate either of
> > > the max constrains.
> > > This was primarily suggested by Ville since he said that we should
> > > always respect what user has set as the upper limit in the bpc
> > > because this could be for example driven by the fact that OEM's
> > > panel has a limitation or issues with higher bpcs or a display requirement
> for certain use case.
> > > Hence while we want to support as high bpc as supported by the
> > > platform and sink to have better display quality, it should not
> > > exceed the max limit set by the user through the property.
> > >
> > > 8 and 10bpc will be supported but we want to start with supporting
> > > the max we can, going down from there if needed.
> > > So for compression, we chose the maximum input bpc and determine the
> > > compressed bpp for that.
> > >
> > >
> > > > We do not consider the actual pipe_bpp while computing the
> > > > compression_bpp, We reverse calculate it from the link_rate, and
> > > > small
> > > joiner bpp limits.
> > > > In cases of forcing dsc, we might have a situation where the link
> > > > can
> > > actually support the current bpp, or even more.
> > > > But we are forcing the dsc enable.
> > > > In such cases we might end up with a compression bpp which is
> > > > higher than
> > > the actual i/p bpp.
> > >
> > > Well the only time we force the dsc_enable is for IGT DSC tests and
> > > thats okay for compression bpp to be higher since there we are just
> > > validation the functionality and its not for actual user/use case.
> >
> > We are having these test cases as part of CI. We hit FIFO underrun in such
> cases and that's treated as a fail.
>
> >
> > >
> > > In the actual use case we will only enable DSC when the available
> > > max link rate/lane count does not support the minimum bpp of 18 (min
> > > bpc of 6 * 3) So then in that case we say that lets keep the
> > > pipe_bpp or input bpp as max_supported_input_bpc * 3
> > > >
> > > > Now, even if we take a min of higher compression bpp against
> > > > max_requested_bpc *3 -1, we still have Compression bpp > actual
> > > > pipe_bpp
> > > >
> > > > As per the spec when they say uncompressed bpp, they actually mean
> > > > 3 * bpc If we go ahead with this approach of using
> > > > max_requested_bpc , which is 12 always we cannot adhere to the spec.
> > >
> > > So the Bspec says that if the input BPP is (8 * 3) = 24, then based
> > > on the engine's compression ratio capability it can support output
> > > compressed BPP
> > > of: 8 - 23 in the increments of 1 BPP And the maximum that we can
> > > pick between 8 - 23 will depend on the min(max bits_per_pixel that
> > > the max link rate, lane count can handle, max bits per pixel by small joiner
> RAM calc).
> >
> > In case of force dsc, as part of the IGT tests, the link can actually
> > support more than 24bpp, since we are forcing have seen a case where it
> could support 28bpp.
> >
>
> From IGT we are forcing DSC for all supported input BPCs right, so for bpc =
> 8, so input bpp = 24. So IMO in the kernel code, when we calculate pipe_bpp
> when force_dsc is set in that case we should use the bpc requested from IGT
> as inpput bpc and not care for max_connector_bpc So then input bpp = 24
> and the limits of compressed bpp would be 8 - 23
Right, had thought of this
Adding a check on force_dsc_en before doing this
pipe_config->pipe_bpp = max_dsc_pipe_bpp;
but since you said that the design was to respect the max_requested_bpc from the user
should we use max_requested_bpc property in the igt to say that set the max to 8bpc
since this test simulates a situation of testing 8bpc panel?
Similarly for 10bpc?
Thanks
Vandita
>
> Ideally now the link rate and lane count should be lowered to use the least
> required to support that compressed bpp Then we wont see any underruns.
>
> Manasi
>
> > So min of (28,(36-1)) would be 28 and not as per the spec.
> >
> > Hence in either of the places, kernel or igt we need to honour the
> > limits Of bpc*3 as per the DP 1.4 spec.
> >
> > If you look at the IGT we have cases of 8bpc, 10 bpc We need to
> > address this either in the driver by getting the actual uncompressed
> > bpp limits Or in the user space by changing the max_requested_bpc for
> 8bpc and 10bpc cases.
> >
> > This patch is tested and resolves the FIFO underruns, in force dsc cases.
> > The problem is only when we are forcing DSC and the link rate can actually
> support higher bpp.
> > And we have multiple igts trying to use 8bpc and 10bpc.
> >
> > Thanks
> > Vandita
> >
> > >
> > > So we are good here in terms of how we calculate our compressed bpp.
> > > However what you should once double check is for XeLPD (>=13)
> > > platforms, you just pick min (bits_per_pixel, pipe_bpp - 1) But I
> > > remember seeing that the spec still says target bpp has to be 8 to
> > > 27 even when supported input bpc are 8/10/12 (please check if it
> > > actually goes all the way from 8 to 35)
> > >
> > > Manasi
> > >
> > > >
> > > > Thanks,
> > > > Vandita
> > > >
> > > > > Manasi
> > > > >
> > > > > >
> > > > > > Fixes: 831d5aa96c97 ("drm/i915/xelpd: Support DP1.4
> > > > > > compression
> > > > > > BPPs")
> > > > > > Signed-off-by: Vandita Kulkarni <vandita.kulkarni at intel.com>
> > > > > > ---
> > > > > > drivers/gpu/drm/i915/display/intel_dp.c | 7 ++++---
> > > > > > 1 file changed, 4 insertions(+), 3 deletions(-)
> > > > > >
> > > > > > diff --git a/drivers/gpu/drm/i915/display/intel_dp.c
> > > > > > b/drivers/gpu/drm/i915/display/intel_dp.c
> > > > > > index 9d8132dd4cc5..1f7e666ae490 100644
> > > > > > --- a/drivers/gpu/drm/i915/display/intel_dp.c
> > > > > > +++ b/drivers/gpu/drm/i915/display/intel_dp.c
> > > > > > @@ -1322,7 +1322,7 @@ static int
> > > > > > intel_dp_dsc_compute_config(struct
> > > > > intel_dp *intel_dp,
> > > > > > struct drm_i915_private *dev_priv = to_i915(dig_port-
> > > > > >base.base.dev);
> > > > > > const struct drm_display_mode *adjusted_mode =
> > > > > > &pipe_config->hw.adjusted_mode;
> > > > > > - int pipe_bpp;
> > > > > > + int pipe_bpp, max_dsc_pipe_bpp;
> > > > > > int ret;
> > > > > >
> > > > > > pipe_config->fec_enable = !intel_dp_is_edp(intel_dp) &&
> @@ -
> > > > > 1331,7
> > > > > > +1331,8 @@ static int intel_dp_dsc_compute_config(struct
> > > > > > +intel_dp
> > > > > *intel_dp,
> > > > > > if (!intel_dp_supports_dsc(intel_dp, pipe_config))
> > > > > > return -EINVAL;
> > > > > >
> > > > > > - pipe_bpp = intel_dp_dsc_compute_bpp(intel_dp, conn_state-
> > > > > >max_requested_bpc);
> > > > > > + pipe_bpp = pipe_config->pipe_bpp;
> > > > > > + max_dsc_pipe_bpp = intel_dp_dsc_compute_bpp(intel_dp,
> > > > > > +conn_state->max_requested_bpc);
> > > > > >
> > > > > > /* Min Input BPC for ICL+ is 8 */
> > > > > > if (pipe_bpp < 8 * 3) {
> > > > > > @@ -1345,7 +1346,7 @@ static int
> > > > > > intel_dp_dsc_compute_config(struct
> > > > > intel_dp *intel_dp,
> > > > > > * Optimize this later for the minimum possible link rate/lane
> count
> > > > > > * with DSC enabled for the requested mode.
> > > > > > */
> > > > > > - pipe_config->pipe_bpp = pipe_bpp;
> > > > > > + pipe_config->pipe_bpp = max_dsc_pipe_bpp;
> > > > > > pipe_config->port_clock = limits->max_rate;
> > > > > > pipe_config->lane_count = limits->max_lane_count;
> > > > > >
> > > > > > --
> > > > > > 2.32.0
> > > > > >
More information about the Intel-gfx
mailing list