[Intel-gfx] [PATCH v2 4/6] drm/i915/gsc: Do a driver-FLR on unload if GSC was loaded
Rodrigo Vivi
rodrigo.vivi at intel.com
Tue Dec 6 08:52:08 UTC 2022
On Mon, Dec 05, 2022 at 05:19:06PM -0800, Daniele Ceraolo Spurio wrote:
> If the GSC was loaded, the only way to stop it during the driver unload
> flow is to do a driver-FLR.
> The driver-initiated FLR is not the same as PCI config space FLR in
> that it doesn't reset the SGUnit and doesn't modify the PCI config
> space. Thus, it doesn't require a re-enumeration of the PCI BARs.
> However, the driver-FLR does cause a memory wipe of graphics memory
> on all discrete GPU platforms or a wipe limited to stolen memory
> on the integrated GPU platforms.
>
> We perform the FLR as the last action before releasing the MMIO bar, so
> that we don't have to care about the consequences of the reset on the
> unload flow.
>
> v2: rename FLR function, add comment to explain FLR impact (Rodrigo),
> better explain why GSC needs FLR (Alan)
>
> Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio at intel.com>
> Signed-off-by: Alan Previn <alan.previn.teres.alexis at intel.com>
> Cc: Rodrigo Vivi <rodrigo.vivi at intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi at intel.com>
> ---
> drivers/gpu/drm/i915/gt/uc/intel_gsc_fw.c | 23 +++++++++
> drivers/gpu/drm/i915/i915_reg.h | 3 ++
> drivers/gpu/drm/i915/intel_uncore.c | 58 +++++++++++++++++++++++
> drivers/gpu/drm/i915/intel_uncore.h | 13 +++++
> 4 files changed, 97 insertions(+)
>
> diff --git a/drivers/gpu/drm/i915/gt/uc/intel_gsc_fw.c b/drivers/gpu/drm/i915/gt/uc/intel_gsc_fw.c
> index f88069ab71ab..e73d4440c5e8 100644
> --- a/drivers/gpu/drm/i915/gt/uc/intel_gsc_fw.c
> +++ b/drivers/gpu/drm/i915/gt/uc/intel_gsc_fw.c
> @@ -166,6 +166,29 @@ int intel_gsc_uc_fw_upload(struct intel_gsc_uc *gsc)
> if (err)
> goto fail;
>
> + /*
> + * GSC is only killed by an FLR, so we need to trigger one on unload to
> + * make sure we stop it. This is because we assign a chunk of memory to
> + * the GSC as part of the FW load , so we need to make sure it stops
> + * using it when we release it to the system on driver unload. Note that
> + * this is not a problem of the unload per-se, because the GSC will not
> + * touch that memory unless there are requests for it coming from the
> + * driver; therefore, no accesses will happen while i915 is not loaded,
> + * but if we re-load the driver then the GSC might wake up and try to
> + * access that old memory location again.
> + * Given that an FLR is a very disruptive action (see the FLR function
> + * for details), we want to do it as the last action before releasing
> + * the access to the MMIO bar, which means we need to do it as part of
> + * the primary uncore cleanup.
> + * An alternative approach to the FLR would be to use a memory location
> + * that survives driver unload, like e.g. stolen memory, and keep the
> + * GSC loaded across reloads. However, this requires us to make sure we
> + * preserve that memory location on unload and then determine and
> + * reserve its offset on each subsequent load, which is not trivial, so
> + * it is easier to just kill everything and start fresh.
> + */
> + intel_uncore_set_flr_on_fini(>->i915->uncore);
> +
> err = gsc_fw_load(gsc);
> if (err)
> goto fail;
> diff --git a/drivers/gpu/drm/i915/i915_reg.h b/drivers/gpu/drm/i915/i915_reg.h
> index 0b90fe6a28f7..b95d533652a4 100644
> --- a/drivers/gpu/drm/i915/i915_reg.h
> +++ b/drivers/gpu/drm/i915/i915_reg.h
> @@ -118,6 +118,9 @@
>
> #define GU_CNTL _MMIO(0x101010)
> #define LMEM_INIT REG_BIT(7)
> +#define DRIVERFLR REG_BIT(31)
> +#define GU_DEBUG _MMIO(0x101018)
> +#define DRIVERFLR_STATUS REG_BIT(31)
>
> #define GEN6_STOLEN_RESERVED _MMIO(0x1082C0)
> #define GEN6_STOLEN_RESERVED_ADDR_MASK (0xFFF << 20)
> diff --git a/drivers/gpu/drm/i915/intel_uncore.c b/drivers/gpu/drm/i915/intel_uncore.c
> index 8006a6c61466..3bfb4af0df78 100644
> --- a/drivers/gpu/drm/i915/intel_uncore.c
> +++ b/drivers/gpu/drm/i915/intel_uncore.c
> @@ -2703,6 +2703,61 @@ void intel_uncore_prune_engine_fw_domains(struct intel_uncore *uncore,
> }
> }
>
> +/*
> + * The driver-initiated FLR is the highest level of reset that we can trigger
> + * from within the driver. It is different from the PCI FLR in that it doesn't
> + * fully reset the SGUnit and doesn't modify the PCI config space and therefore
> + * it doesn't require a re-enumeration of the PCI BARs. However, the
> + * driver-initiated FLR does still cause a reset of both GT and display and a
> + * memory wipe of local and stolen memory, so recovery would require a full HW
> + * re-init and saving/restoring (or re-populating) the wiped memory. Since we
> + * perform the FLR as the very last action before releasing access to the HW
> + * during the driver release flow, we don't attempt recovery at all, because
> + * if/when a new instance of i915 is bound to the device it will do a full
> + * re-init anyway.
> + */
> +static void driver_initiated_flr(struct intel_uncore *uncore)
> +{
> + struct drm_i915_private *i915 = uncore->i915;
> + const unsigned int flr_timeout_ms = 3000; /* specs recommend a 3s wait */
> + int ret;
> +
> + drm_dbg(&i915->drm, "Triggering Driver-FLR\n");
> +
> + /*
> + * Make sure any pending FLR requests have cleared by waiting for the
> + * FLR trigger bit to go to zero. Also clear GU_DEBUG's DRIVERFLR_STATUS
> + * to make sure it's not still set from a prior attempt (it's a write to
> + * clear bit).
> + * Note that we should never be in a situation where a previous attempt
> + * is still pending (unless the HW is totally dead), but better to be
> + * safe in case something unexpected happens
> + */
> + ret = intel_wait_for_register_fw(uncore, GU_CNTL, DRIVERFLR, 0, flr_timeout_ms);
> + if (ret) {
> + drm_err(&i915->drm,
> + "Failed to wait for Driver-FLR bit to clear! %d\n",
> + ret);
> + return;
> + }
> + intel_uncore_write_fw(uncore, GU_DEBUG, DRIVERFLR_STATUS);
> +
> + /* Trigger the actual Driver-FLR */
> + intel_uncore_rmw_fw(uncore, GU_CNTL, 0, DRIVERFLR);
> +
> + ret = intel_wait_for_register_fw(uncore, GU_DEBUG,
> + DRIVERFLR_STATUS, DRIVERFLR_STATUS,
> + flr_timeout_ms);
> + if (ret) {
> + drm_err(&i915->drm, "wait for Driver-FLR completion failed! %d\n", ret);
> + return;
> + }
> +
> + intel_uncore_write_fw(uncore, GU_DEBUG, DRIVERFLR_STATUS);
> +
> + return;
> +}
> +
> /* Called via drm-managed action */
> void intel_uncore_fini_mmio(struct drm_device *dev, void *data)
> {
> @@ -2716,6 +2771,9 @@ void intel_uncore_fini_mmio(struct drm_device *dev, void *data)
> intel_uncore_fw_domains_fini(uncore);
> iosf_mbi_punit_release();
> }
> +
> + if (intel_uncore_needs_flr_on_fini(uncore))
> + driver_initiated_flr(uncore);
> }
>
> /**
> diff --git a/drivers/gpu/drm/i915/intel_uncore.h b/drivers/gpu/drm/i915/intel_uncore.h
> index e9e38490815d..9ea1f4864a3a 100644
> --- a/drivers/gpu/drm/i915/intel_uncore.h
> +++ b/drivers/gpu/drm/i915/intel_uncore.h
> @@ -153,6 +153,7 @@ struct intel_uncore {
> #define UNCORE_HAS_FPGA_DBG_UNCLAIMED BIT(1)
> #define UNCORE_HAS_DBG_UNCLAIMED BIT(2)
> #define UNCORE_HAS_FIFO BIT(3)
> +#define UNCORE_NEEDS_FLR_ON_FINI BIT(4)
>
> const struct intel_forcewake_range *fw_domains_table;
> unsigned int fw_domains_table_entries;
> @@ -223,6 +224,18 @@ intel_uncore_has_fifo(const struct intel_uncore *uncore)
> return uncore->flags & UNCORE_HAS_FIFO;
> }
>
> +static inline bool
> +intel_uncore_needs_flr_on_fini(const struct intel_uncore *uncore)
> +{
> + return uncore->flags & UNCORE_NEEDS_FLR_ON_FINI;
> +}
> +
> +static inline bool
> +intel_uncore_set_flr_on_fini(struct intel_uncore *uncore)
> +{
> + return uncore->flags |= UNCORE_NEEDS_FLR_ON_FINI;
> +}
> +
> void intel_uncore_mmio_debug_init_early(struct drm_i915_private *i915);
> void intel_uncore_init_early(struct intel_uncore *uncore,
> struct intel_gt *gt);
> --
> 2.37.3
>
More information about the Intel-gfx
mailing list