[Intel-gfx] [PATCH v2 1/3] drm/i915: Initialize eDP source rates after per-panel VBT parsing

[Ville Syrjala]

From: Ville Syrjälä <ville.syrjala at linux.intel.com>

We'll need to know the VBT panel_type before we can determine the
maximum link rate for eDP. To that end move
intel_dp_set_source_rates() & co. to be called after the per-panel
VBT parsing has been done.

intel_dp_mst_encoder_init() depends on the source rates so we'll
have to do it a bit later as well.

v2: Fix the intel_dp_mst_encoder_init() oops

Reviewed-by: Jani Nikula <jani.nikula at intel.com> #v1
Signed-off-by: Ville Syrjälä <ville.syrjala at linux.intel.com>
---
 drivers/gpu/drm/i915/display/intel_dp.c | 19 ++++++++-----------
 1 file changed, 8 insertions(+), 11 deletions(-)

diff --git a/drivers/gpu/drm/i915/display/intel_dp.c b/drivers/gpu/drm/i915/display/intel_dp.c
index b8e2d3cd4d68..60b89a722bd8 100644
--- a/drivers/gpu/drm/i915/display/intel_dp.c
+++ b/drivers/gpu/drm/i915/display/intel_dp.c
@@ -2852,9 +2852,6 @@ intel_edp_init_dpcd(struct intel_dp *intel_dp)
 		intel_dp_set_sink_rates(intel_dp);
 	intel_dp_set_max_sink_lane_count(intel_dp);
 
-	intel_dp_set_common_rates(intel_dp);
-	intel_dp_reset_max_link_params(intel_dp);
-
 	/* Read the eDP DSC DPCD registers */
 	if (DISPLAY_VER(dev_priv) >= 10)
 		intel_dp_get_dsc_sink_cap(intel_dp);
@@ -5342,11 +5339,8 @@ intel_dp_init_connector(struct intel_digital_port *dig_port,
 		type = DRM_MODE_CONNECTOR_DisplayPort;
 	}
 
-	intel_dp_set_source_rates(intel_dp);
 	intel_dp_set_default_sink_rates(intel_dp);
 	intel_dp_set_default_max_sink_lane_count(intel_dp);
-	intel_dp_set_common_rates(intel_dp);
-	intel_dp_reset_max_link_params(intel_dp);
 
 	if (IS_VALLEYVIEW(dev_priv) || IS_CHERRYVIEW(dev_priv))
 		intel_dp->pps.active_pipe = vlv_active_pipe(intel_dp);
@@ -5374,16 +5368,19 @@ intel_dp_init_connector(struct intel_digital_port *dig_port,
 	else
 		intel_connector->get_hw_state = intel_connector_get_hw_state;
 
-	/* init MST on ports that can support it */
-	intel_dp_mst_encoder_init(dig_port,
-				  intel_connector->base.base.id);
-
 	if (!intel_edp_init_connector(intel_dp, intel_connector)) {
 		intel_dp_aux_fini(intel_dp);
-		intel_dp_mst_encoder_cleanup(dig_port);
 		goto fail;
 	}
 
+	intel_dp_set_source_rates(intel_dp);
+	intel_dp_set_common_rates(intel_dp);
+	intel_dp_reset_max_link_params(intel_dp);
+
+	/* init MST on ports that can support it */
+	intel_dp_mst_encoder_init(dig_port,
+				  intel_connector->base.base.id);
+
 	intel_dp_add_properties(intel_dp, connector);
 
 	if (is_hdcp_supported(dev_priv, port) && !intel_dp_is_edp(intel_dp)) {
-- 
2.35.1