[Intel-gfx] [PATCH 8/9] drm/i915/display/mtl: Fill port width in DDI_BUF_/TRANS_DDI_FUNC_/PORT_BUF_CTL for HDMI
Radhakrishna Sripada
radhakrishna.sripada at intel.com
Thu Apr 13 21:01:19 UTC 2023
From: Ankit Nautiyal <ankit.k.nautiyal at intel.com>
MTL requires the PORT_CTL_WIDTH, TRANS_DDI_FUNC_CTL and DDI_BUF_CTL
to be filled with 4 lanes for TMDS mode.
This patch enables D2D link and fills PORT_WIDTH in appropriate
registers.
v2:
- Added fixes from Clint's Add HDMI implementation changes.
- Modified commit message.
v3:
- Use TRANS_DDI_PORT_WIDTH() instead of DDI_PORT_WIDTH() for the value
of TRANS_DDI_FUNC_CTL_*. (Gustavo)
Cc: Taylor, Clinton A <clinton.a.taylor at intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal at intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada at intel.com>
Signed-off-by: Mika Kahola <mika.kahola at intel.com>
Reviewed-by: Imre Deak <imre.deak at intel.com>
---
drivers/gpu/drm/i915/display/intel_ddi.c | 32 ++++++++++++++++++++++--
drivers/gpu/drm/i915/i915_reg.h | 2 ++
2 files changed, 32 insertions(+), 2 deletions(-)
diff --git a/drivers/gpu/drm/i915/display/intel_ddi.c b/drivers/gpu/drm/i915/display/intel_ddi.c
index c0283829823f..ea012d7f378f 100644
--- a/drivers/gpu/drm/i915/display/intel_ddi.c
+++ b/drivers/gpu/drm/i915/display/intel_ddi.c
@@ -541,6 +541,8 @@ intel_ddi_transcoder_func_reg_val_get(struct intel_encoder *encoder,
temp |= TRANS_DDI_HDMI_SCRAMBLING;
if (crtc_state->hdmi_high_tmds_clock_ratio)
temp |= TRANS_DDI_HIGH_TMDS_CHAR_RATE;
+ if (DISPLAY_VER(dev_priv) >= 14)
+ temp |= TRANS_DDI_PORT_WIDTH(crtc_state->lane_count);
} else if (intel_crtc_has_type(crtc_state, INTEL_OUTPUT_ANALOG)) {
temp |= TRANS_DDI_MODE_SELECT_FDI_OR_128B132B;
temp |= (crtc_state->fdi_lanes - 1) << 1;
@@ -3157,6 +3159,10 @@ static void intel_enable_ddi_hdmi(struct intel_atomic_state *state,
if (has_buf_trans_select(dev_priv))
hsw_prepare_hdmi_ddi_buffers(encoder, crtc_state);
+ /* e. Enable D2D Link for C10/C20 Phy */
+ if (DISPLAY_VER(dev_priv) >= 14)
+ mtl_ddi_enable_d2d(encoder);
+
encoder->set_signal_levels(encoder, crtc_state);
/* Display WA #1143: skl,kbl,cfl */
@@ -3202,12 +3208,30 @@ static void intel_enable_ddi_hdmi(struct intel_atomic_state *state,
*
* On ADL_P the PHY link rate and lane count must be programmed but
* these are both 0 for HDMI.
+ *
+ * But MTL onwards HDMI2.1 is supported and in TMDS mode this
+ * is filled with lane count, already set in the crtc_state.
+ * The same is required to be filled in PORT_BUF_CTL for C10/20 Phy.
*/
buf_ctl = dig_port->saved_port_bits | DDI_BUF_CTL_ENABLE;
- if (IS_ALDERLAKE_P(dev_priv) && intel_phy_is_tc(dev_priv, phy)) {
+ if (DISPLAY_VER(dev_priv) >= 14) {
+ u8 lane_count = mtl_get_port_width(crtc_state->lane_count);
+ u32 port_buf = 0;
+
+ port_buf |= XELPDP_PORT_WIDTH(lane_count);
+
+ if (dig_port->saved_port_bits & DDI_BUF_PORT_REVERSAL)
+ port_buf |= XELPDP_PORT_REVERSAL;
+
+ intel_de_rmw(dev_priv, XELPDP_PORT_BUF_CTL1(port),
+ XELPDP_PORT_WIDTH_MASK | XELPDP_PORT_REVERSAL, port_buf);
+
+ buf_ctl |= DDI_PORT_WIDTH(lane_count);
+ } else if (IS_ALDERLAKE_P(dev_priv) && intel_phy_is_tc(dev_priv, phy)) {
drm_WARN_ON(&dev_priv->drm, !intel_tc_port_in_legacy_mode(dig_port));
buf_ctl |= DDI_BUF_CTL_TC_PHY_OWNERSHIP;
}
+
intel_de_write(dev_priv, DDI_BUF_CTL(port), buf_ctl);
intel_wait_ddi_buf_active(dev_priv, port);
@@ -3668,7 +3692,11 @@ static void intel_ddi_read_func_ctl(struct intel_encoder *encoder,
fallthrough;
case TRANS_DDI_MODE_SELECT_DVI:
pipe_config->output_types |= BIT(INTEL_OUTPUT_HDMI);
- pipe_config->lane_count = 4;
+ if (DISPLAY_VER(dev_priv) >= 14)
+ pipe_config->lane_count =
+ ((temp & DDI_PORT_WIDTH_MASK) >> DDI_PORT_WIDTH_SHIFT) + 1;
+ else
+ pipe_config->lane_count = 4;
break;
case TRANS_DDI_MODE_SELECT_DP_SST:
if (encoder->type == INTEL_OUTPUT_EDP)
diff --git a/drivers/gpu/drm/i915/i915_reg.h b/drivers/gpu/drm/i915/i915_reg.h
index df29ab301326..f472baf242dc 100644
--- a/drivers/gpu/drm/i915/i915_reg.h
+++ b/drivers/gpu/drm/i915/i915_reg.h
@@ -5596,6 +5596,8 @@ enum skl_power_gate {
#define TRANS_DDI_HDCP_SELECT REG_BIT(5)
#define TRANS_DDI_BFI_ENABLE (1 << 4)
#define TRANS_DDI_HIGH_TMDS_CHAR_RATE (1 << 4)
+#define TRANS_DDI_PORT_WIDTH_MASK REG_GENMASK(3, 1)
+#define TRANS_DDI_PORT_WIDTH(width) REG_FIELD_PREP(TRANS_DDI_PORT_WIDTH_MASK, (width) - 1)
#define TRANS_DDI_HDMI_SCRAMBLING (1 << 0)
#define TRANS_DDI_HDMI_SCRAMBLING_MASK (TRANS_DDI_HDMI_SCRAMBLER_CTS_ENABLE \
| TRANS_DDI_HDMI_SCRAMBLER_RESET_FREQ \
--
2.34.1
More information about the Intel-gfx
mailing list