[Intel-gfx] [PATCH] drm/i915/guc: Disable PL1 power limit when loading GuC firmware
Dixit, Ashutosh
ashutosh.dixit at intel.com
Mon Mar 27 16:57:03 UTC 2023
On Fri, 24 Mar 2023 17:06:33 -0700, Belgaumkar, Vinay wrote:
>
Hi Vinay,
> On 3/24/2023 4:31 PM, Dixit, Ashutosh wrote:
> > On Fri, 24 Mar 2023 11:15:02 -0700, Belgaumkar, Vinay wrote:
> > Hi Vinay,
> >
> > Thanks for the review. Comments inline below.
> Sorry about asking the same questions all over again :) Didn't look at
> previous versions.
Np, the previous versions were buried somewhere anyway that's why I
provided the link.
> >
> >> On 3/15/2023 8:59 PM, Ashutosh Dixit wrote:
> >>> On dGfx, the PL1 power limit being enabled and set to a low value results
> >>> in a low GPU operating freq. It also negates the freq raise operation which
> >>> is done before GuC firmware load. As a result GuC firmware load can time
> >>> out. Such timeouts were seen in the GL #8062 bug below (where the PL1 power
> >>> limit was enabled and set to a low value). Therefore disable the PL1 power
> >>> limit when allowed by HW when loading GuC firmware.
> >> v3 label missing in subject.
> >>> v2:
> >>> - Take mutex (to disallow writes to power1_max) across GuC reset/fw load
> >>> - Add hwm_power_max_restore to error return code path
> >>>
> >>> v3 (Jani N):
> >>> - Add/remove explanatory comments
> >>> - Function renames
> >>> - Type corrections
> >>> - Locking annotation
> >>>
> >>> Link: https://gitlab.freedesktop.org/drm/intel/-/issues/8062
> >>> Signed-off-by: Ashutosh Dixit <ashutosh.dixit at intel.com>
> >>> ---
> >>> drivers/gpu/drm/i915/gt/uc/intel_uc.c | 9 +++++++
> >>> drivers/gpu/drm/i915/i915_hwmon.c | 39 +++++++++++++++++++++++++++
> >>> drivers/gpu/drm/i915/i915_hwmon.h | 7 +++++
> >>> 3 files changed, 55 insertions(+)
> >>>
> >>> diff --git a/drivers/gpu/drm/i915/gt/uc/intel_uc.c b/drivers/gpu/drm/i915/gt/uc/intel_uc.c
> >>> index 4ccb4be4c9cba..aa8e35a5636a0 100644
> >>> --- a/drivers/gpu/drm/i915/gt/uc/intel_uc.c
> >>> +++ b/drivers/gpu/drm/i915/gt/uc/intel_uc.c
> >>> @@ -18,6 +18,7 @@
> >>> #include "intel_uc.h"
> >>> #include "i915_drv.h"
> >>> +#include "i915_hwmon.h"
> >>> static const struct intel_uc_ops uc_ops_off;
> >>> static const struct intel_uc_ops uc_ops_on;
> >>> @@ -461,6 +462,7 @@ static int __uc_init_hw(struct intel_uc *uc)
> >>> struct intel_guc *guc = &uc->guc;
> >>> struct intel_huc *huc = &uc->huc;
> >>> int ret, attempts;
> >>> + bool pl1en;
> >> Init to 'false' here
> > See next comment.
> >
> >>
> >>> GEM_BUG_ON(!intel_uc_supports_guc(uc));
> >>> GEM_BUG_ON(!intel_uc_wants_guc(uc));
> >>> @@ -491,6 +493,9 @@ static int __uc_init_hw(struct intel_uc *uc)
> >>> else
> >>> attempts = 1;
> >>> + /* Disable a potentially low PL1 power limit to allow freq to be
> >>> raised */
> >>> + i915_hwmon_power_max_disable(gt->i915, &pl1en);
> >>> +
> >>> intel_rps_raise_unslice(&uc_to_gt(uc)->rps);
> >>> while (attempts--) {
> >>> @@ -547,6 +552,8 @@ static int __uc_init_hw(struct intel_uc *uc)
> >>> intel_rps_lower_unslice(&uc_to_gt(uc)->rps);
> >>> }
> >>> + i915_hwmon_power_max_restore(gt->i915, pl1en);
> >>> +
> >>> guc_info(guc, "submission %s\n", str_enabled_disabled(intel_uc_uses_guc_submission(uc)));
> >>> guc_info(guc, "SLPC %s\n", str_enabled_disabled(intel_uc_uses_guc_slpc(uc)));
> >>> @@ -563,6 +570,8 @@ static int __uc_init_hw(struct intel_uc *uc)
> >>> /* Return GT back to RPn */
> >>> intel_rps_lower_unslice(&uc_to_gt(uc)->rps);
> >>> + i915_hwmon_power_max_restore(gt->i915, pl1en);
> >> if (pl1en)
> >>
> >> i915_hwmon_power_max_enable().
> > IMO it's better not to have checks in the main __uc_init_hw() function (if
> > we do this we'll need to add 2 checks in __uc_init_hw()). If you really
> > want we could do something like this inside
> > i915_hwmon_power_max_disable/i915_hwmon_power_max_restore. But for now I
> > am not making any changes.
> ok.
> >
> > (I can send a patch with the changes if you want to take a look but IMO it
> > will add more logic/code but without real benefits (it will save a rmw if
> > the limit was already disabled, but IMO this code is called so infrequently
> > (only during GuC resets) as to not have any significant impact)).
> >
> >>> +
> >>> __uc_sanitize(uc);
> >>> if (!ret) {
> >>> diff --git a/drivers/gpu/drm/i915/i915_hwmon.c b/drivers/gpu/drm/i915/i915_hwmon.c
> >>> index ee63a8fd88fc1..769b5bda4d53f 100644
> >>> --- a/drivers/gpu/drm/i915/i915_hwmon.c
> >>> +++ b/drivers/gpu/drm/i915/i915_hwmon.c
> >>> @@ -444,6 +444,45 @@ hwm_power_write(struct hwm_drvdata *ddat, u32 attr, int chan, long val)
> >>> }
> >>> }
> >>> +void i915_hwmon_power_max_disable(struct drm_i915_private *i915, bool
> >>> *old)
> >> Shouldn't we call this i915_hwmon_package_pl1_disable()?
> > I did think of using "pl1" in the function name but then decided to retain
> > "power_max" because other hwmon functions for PL1 limit also use
> > "power_max" (hwm_power_max_read/hwm_power_max_write) and currently
> > "hwmon_power_max" is mapped to the PL1 limit. So "power_max" is used to
> > show that all these functions deal with the PL1 power limit.
> >
> > There is a comment in __uc_init_hw() explaining "power_max" means the PL1
> > power limit.
> ok.
> >
> >>> + __acquires(i915->hwmon->hwmon_lock)
> >>> +{
> >>> + struct i915_hwmon *hwmon = i915->hwmon;
> >>> + intel_wakeref_t wakeref;
> >>> + u32 r;
> >>> +
> >>> + if (!hwmon || !i915_mmio_reg_valid(hwmon->rg.pkg_rapl_limit))
> >>> + return;
> >>> +
> >>> + /* Take mutex to prevent concurrent hwm_power_max_write */
> >>> + mutex_lock(&hwmon->hwmon_lock);
> >>> +
> >>> + with_intel_runtime_pm(hwmon->ddat.uncore->rpm, wakeref)
> >>> + r = intel_uncore_rmw(hwmon->ddat.uncore,
> >>> + hwmon->rg.pkg_rapl_limit,
> >>> + PKG_PWR_LIM_1_EN, 0);
> >> Most of this code (lock and rmw parts) is already inside static void
> >> hwm_locked_with_pm_intel_uncore_rmw() , can we reuse that here?
> > This was the case in v1 of the patch:
> >
> > https://patchwork.freedesktop.org/patch/526393/?series=115003&rev=1
> >
> > But now this cannot be done because if you notice we acquire the mutex in
> > i915_hwmon_power_max_disable() and release the mutex in
> > i915_hwmon_power_max_restore().
> >
> > I explained the reason why this the mutex is handled this way in my reply
> > to Jani Nikula here:
> >
> > https://patchwork.freedesktop.org/patch/526598/?series=115003&rev=2
> >
> > Quoting below:
> >
> > ```
> >>> + /* hwmon_lock mutex is unlocked in hwm_power_max_restore */
> >> Not too happy about that... any better ideas?
> > Afais, taking the mutex is the only fully correct solution (when we disable
> > the power limit, userspace can go re-enable it). Examples of partly
> > incorrect solutions (which don't take the mutex) include:
> >
> > a. Don't take the mutex, don't do anything, ignore any changes to the value
> > if it has changed during GuC reset/fw load (just overwrite the changed
> > value). Con: changed value is lost.
> >
> > b. Detect if the value has changed (the limit has been re-enabled) after we
> > have disabled the limit and in that case skip restoring the value. But
> > then someone can say why do we allow enabling the PL1 limit since we
> > want to disable it.
> >
> > Both these are very unlikely scenarios so they might work. But I would
> > first like to explore if holding a mutex across GuC reset is prolebmatic
> > since that is /the/ correct solution. But if anyone comes up with a reason
> > why that cannot be done we can look at these other not completely correct
> > options.
>
> Well, one reason is that this is adding a lot of duplicate/non-reusable
> code needlessly. If it gets re-used elsewhere, that could lead to some
> weird situations where the lock could be held for an extended period of
> time and introduce dependencies.
The lock will only be held if userspace tries to set the PL1 limit while
GuC load is in progress. The chance of this is low (though not
zero). Otherwise the lock will be uncontended. But otherwise yes the lock
is being held across GuC load. I would think as long as GuC load completes
in the 200 ms (or even a few seconds) it should not be an issue. These
hwmon operations are happening very infrequently, say in a matter of
seconds, at least 100's of milliseconds.
We could add a different lock here but I don't think it's worth it.
> Also, how/why would the user modify this
> PL1 during guc load? The sysfs interfaces are not even ready at this point?
> Even if we consider this during a resume, the terminal will not be
> available to the user.
A few points:
* Agree about probe, the sysfs doesn't exist
* About resume, again agreed. But in general a userspace process (say a
daemon) might be writing to hwmon sysfs even when a terminal is not
available. hwmon is accessed by L0 sysman e.g.
* Finally, GuC is not loaded only during probe and resume but GuC can also
get reset because of error conditions. When the sysfs and the terminal
are available (e.g what if you set a low PL1 limit and then run
i915_hangman, it fails currently as was seen in CI, I will try to write
an IGT for this).
So that's the reason for taking the lock. I think it's not a big problem
even if we take the lock that is why it is in the patch.
> > ```
> >
> >>> +
> >>> + *old = !!(r & PKG_PWR_LIM_1_EN);
> >>> +}
> >>> +
> >>> +void i915_hwmon_power_max_restore(struct drm_i915_private *i915, bool old)
> >>> + __releases(i915->hwmon->hwmon_lock)
> >> We can just call this i915_hwmon_power_max_enable() and call whenever the
> >> old value was actually enabled. That way, we have proper mirror functions.
> > As I explained that would mean adding two checks in the main __uc_init_hw()
> > function which I am trying to avoid. So we have disable/restore pair.
> >
> >>> +{
> >>> + struct i915_hwmon *hwmon = i915->hwmon;
> >>> + intel_wakeref_t wakeref;
> >>> +
> >>> + if (!hwmon || !i915_mmio_reg_valid(hwmon->rg.pkg_rapl_limit))
> >>> + return;
> >>> +
> >>> + with_intel_runtime_pm(hwmon->ddat.uncore->rpm, wakeref)
> >>> + intel_uncore_rmw(hwmon->ddat.uncore,
> >>> + hwmon->rg.pkg_rapl_limit,
> >>> + PKG_PWR_LIM_1_EN,
> >>> + old ? PKG_PWR_LIM_1_EN : 0);
> >> 3rd param should be 0 here, else we will end up clearing other bits.
> > No see intel_uncore_rmw(), it will only clear the PKG_PWR_LIM_1_EN bit, so
> > the code here is correct. intel_uncore_rmw() does:
> >
> > val = (old & ~clear) | set;
> Ok, just confusing, since you are also setting it with the 4th param.
No, the 3rd param is clearing (old & ~clear) and the 4th param is setting
(| set). Look at intel_uncore_rmw(). Also I've tested this patch ;-)
Thanks.
--
Ashutosh
> >
> > So for now I am not making any changes, if you feel strongly about
> > something one way or another let me know. Anyway these comments should help
> > you understand the patch better so take a look and we can go from there.
> >
> > Thanks.
> > --
> > Ashutosh
> >
> >>> +
> >>> + mutex_unlock(&hwmon->hwmon_lock);
> >>> +}
> >>> +
> >>> static umode_t
> >>> hwm_energy_is_visible(const struct hwm_drvdata *ddat, u32 attr)
> >>> {
> >>> diff --git a/drivers/gpu/drm/i915/i915_hwmon.h b/drivers/gpu/drm/i915/i915_hwmon.h
> >>> index 7ca9cf2c34c96..0fcb7de844061 100644
> >>> --- a/drivers/gpu/drm/i915/i915_hwmon.h
> >>> +++ b/drivers/gpu/drm/i915/i915_hwmon.h
> >>> @@ -7,14 +7,21 @@
> >>> #ifndef __I915_HWMON_H__
> >>> #define __I915_HWMON_H__
> >>> +#include <linux/types.h>
> >>> +
> >>> struct drm_i915_private;
> >>> +struct intel_gt;
> >>> #if IS_REACHABLE(CONFIG_HWMON)
> >>> void i915_hwmon_register(struct drm_i915_private *i915);
> >>> void i915_hwmon_unregister(struct drm_i915_private *i915);
> >>> +void i915_hwmon_power_max_disable(struct drm_i915_private *i915, bool *old);
> >>> +void i915_hwmon_power_max_restore(struct drm_i915_private *i915, bool old);
> >>> #else
> >>> static inline void i915_hwmon_register(struct drm_i915_private *i915) { };
> >>> static inline void i915_hwmon_unregister(struct drm_i915_private *i915) { };
> >>> +static inline void i915_hwmon_power_max_disable(struct drm_i915_private *i915, bool *old) { };
> >>> +static inline void i915_hwmon_power_max_restore(struct drm_i915_private *i915, bool old) { };
> >>> #endif
> >>> #endif /* __I915_HWMON_H__ */
More information about the Intel-gfx
mailing list