[PATCH 1/5] vfio: update kernel headers.
Gerd Hoffmann
kraxel at redhat.com
Fri Jan 11 09:31:12 UTC 2019
Temporary, for testing convinience.
Once qemu master is synced with the linux 5.0-rc1 headers
this is not needed any more.
Signed-off-by: Gerd Hoffmann <kraxel at redhat.com>
---
linux-headers/linux/vfio.h | 50 ++++++++++++++++++++++++++++++++++++++++++++++
1 file changed, 50 insertions(+)
diff --git a/linux-headers/linux/vfio.h b/linux-headers/linux/vfio.h
index ceb6453394..51662a7209 100644
--- a/linux-headers/linux/vfio.h
+++ b/linux-headers/linux/vfio.h
@@ -303,6 +303,56 @@ struct vfio_region_info_cap_type {
#define VFIO_REGION_SUBTYPE_INTEL_IGD_HOST_CFG (2)
#define VFIO_REGION_SUBTYPE_INTEL_IGD_LPC_CFG (3)
+#define VFIO_REGION_TYPE_GFX (1)
+#define VFIO_REGION_SUBTYPE_GFX_EDID (1)
+
+/**
+ * struct vfio_region_gfx_edid - EDID region layout.
+ *
+ * Set display link state and EDID blob.
+ *
+ * The EDID blob has monitor information such as brand, name, serial
+ * number, physical size, supported video modes and more.
+ *
+ * This special region allows userspace (typically qemu) set a virtual
+ * EDID for the virtual monitor, which allows a flexible display
+ * configuration.
+ *
+ * For the edid blob spec look here:
+ * https://en.wikipedia.org/wiki/Extended_Display_Identification_Data
+ *
+ * On linux systems you can find the EDID blob in sysfs:
+ * /sys/class/drm/${card}/${connector}/edid
+ *
+ * You can use the edid-decode ulility (comes with xorg-x11-utils) to
+ * decode the EDID blob.
+ *
+ * @edid_offset: location of the edid blob, relative to the
+ * start of the region (readonly).
+ * @edid_max_size: max size of the edid blob (readonly).
+ * @edid_size: actual edid size (read/write).
+ * @link_state: display link state (read/write).
+ * VFIO_DEVICE_GFX_LINK_STATE_UP: Monitor is turned on.
+ * VFIO_DEVICE_GFX_LINK_STATE_DOWN: Monitor is turned off.
+ * @max_xres: max display width (0 == no limitation, readonly).
+ * @max_yres: max display height (0 == no limitation, readonly).
+ *
+ * EDID update protocol:
+ * (1) set link-state to down.
+ * (2) update edid blob and size.
+ * (3) set link-state to up.
+ */
+struct vfio_region_gfx_edid {
+ __u32 edid_offset;
+ __u32 edid_max_size;
+ __u32 edid_size;
+ __u32 max_xres;
+ __u32 max_yres;
+ __u32 link_state;
+#define VFIO_DEVICE_GFX_LINK_STATE_UP 1
+#define VFIO_DEVICE_GFX_LINK_STATE_DOWN 2
+};
+
/*
* The MSIX mappable capability informs that MSIX data of a BAR can be mmapped
* which allows direct access to non-MSIX registers which happened to be within
--
2.9.3
More information about the intel-gvt-dev
mailing list