Problems with HP lt4112 Gobi 4G Module

[Harald Jung]

I've tried to use the alternate bconfiguration value which messed things 
up completly :/
The AT Ports stopped to work with ModemManager.
Are there examples in ModemManager with such a mixed setup?

just forgot:
When i sent the command via minicom, ModemManager didn't recognized 
anything about it.

Harald


Am 18.02.2016 um 21:31 schrieb Dan Williams:
> On Thu, 2016-02-18 at 20:10 +0100, Harald Jung wrote:
>> ^DHCP:5316546d,f8ffffff,5116546d,5116546d,7e1e078b,7d1e078b,43200000,
>> 43200000
> Ok, so it's completely happy to report the IP with the AT command, but
> it doesn't report it through QMI.  Stupid firmware...
>
> Is there any way to switch these things to plain AT+cdc_ncm mode and
> just use Huawei NDISDUP instead of QMI?
>
> Dan
>
>> Am 18.02.2016 um 19:58 schrieb Dan Williams:
>>> On Thu, 2016-02-18 at 19:43 +0100, Harald Jung wrote:
>>>> Hi,
>>>>
>>>> the strange thing is I'm still able to obtain stuff by an dhcp
>>>> request,
>>>> so it is not "really" disconnected.
>>>>
>>>> qmicli -d /dev/cdc-wdm0 --wds-start-network=web.vodafone.de
>>>> --client-no-release-cid
>>>> [/dev/cdc-wdm0] Network started
>>>>            Packet data handle: '1138179280'
>>>> [/dev/cdc-wdm0] Client ID not released:
>>>>            Service: 'wds'
>>>>                CID: '5'
>>>> ThinClient,initial:root:~ $ qmicli -d /dev/cdc-wdm0
>>>> --wds-get-current-settings --client-no-release-cid --client-cid=5
>>>> error: couldn't get current settings: QMI protocol error (15):
>>>> 'OutOfCall'
>>>> [/dev/cdc-wdm0] Client ID not released:
>>>>            Service: 'wds'
>>>>                CID: '5'
>>>> ThinClient,initial:root:~ $ /usr/sbin/dhcpcd -B -K -L -A -G -c
>>>> /usr/libexec/nm-dhcp-helper -4 wwan0
>>>> wwan0: rebinding lease of 109.84.22.83
>>>> wwan0: leased 109.84.22.83 for 7200 seconds
>>>> wwan0: adding route to 109.84.22.80/29
>>> My original thought after reading your logs was that the device was
>>> just stupid and that it might work with DHCP.  I got side-tracked
>>> trying to bring up my ME906E (which your lt4112 is an OEM version
>>> of,
>>> though yours runs QMI and the stock ME906E does NDISDUP).
>>>
>>> But given that the device clearly still has NDISDUP commands lying
>>> around in its firmware, perhaps the lt4112 only likes DHCP?  I'd
>>> love
>>> to see the "AT^DHCP?" output from that device once it's connected,
>>> can
>>> you get that?  Even if you send it to the modem, it might get read
>>> by
>>> ModemManager and appear in the MM logs, FYI.
>>>
>>> Dan
>>>
>>>
>>>> Harald
>>>>
>>>> Am 18.02.2016 um 19:36 schrieb Bjørn Mork:
>>>>> Harald Jung <harald.jung at ecos.de> writes:
>>>>>
>>>>>> [18 Feb 2016, 19:35:12] [Debug] [/dev/cdc-wdm0] Received
>>>>>> message
>>>>>> (translated)...
>>>>>>>>>>>> QMUX:
>>>>>>>>>>>>      length  = 33
>>>>>>>>>>>>      flags   = 0x80
>>>>>>>>>>>>      service = "wds"
>>>>>>>>>>>>      client  = 255
>>>>>>>>>>>> QMI:
>>>>>>>>>>>>      flags       = "indication"
>>>>>>>>>>>>      transaction = 0
>>>>>>>>>>>>      tlv_length  = 21
>>>>>>>>>>>>      message     = "Packet Service Status"
>>>>>>>>>>>> (0x0022)
>>>>>>>>>>>> TLV:
>>>>>>>>>>>>      type       = "Connection Status" (0x01)
>>>>>>>>>>>>      length     = 2
>>>>>>>>>>>>      value      = 01:00
>>>>>>>>>>>>      translated = [ status = 'disconnected'
>>>>>> reconfiguration_required = 'no' ]
>>>>>>>>>>>> TLV:
>>>>>>>>>>>>      type       = "Call End Reason" (0x10)
>>>>>>>>>>>>      length     = 2
>>>>>>>>>>>>      value      = 02:00
>>>>>>>>>>>>      translated = generic-client-end
>>>>>>>>>>>> TLV:
>>>>>>>>>>>>      type       = "Verbose Call End Reason" (0x11)
>>>>>>>>>>>>      length     = 4
>>>>>>>>>>>>      value      = 03:00:D0:07
>>>>>>>>>>>>      translated = [ type = 'cm' reason = '2000' ]
>>>>>>>>>>>> TLV:
>>>>>>>>>>>>      type       = "IP Family" (0x12)
>>>>>>>>>>>>      length     = 1
>>>>>>>>>>>>      value      = 04
>>>>>>>>>>>>      translated = ipv4
>>>>> OK, this is interesting although I have no idea why it
>>>>> happens.  But you
>>>>> are disconnected for reason '2000', whatever that is.
>>>>>
>>>>>
>>>>> Bjørn
>>>> _______________________________________________
>>>> libqmi-devel mailing list
>>>> libqmi-devel at lists.freedesktop.org
>>>> https://lists.freedesktop.org/mailman/listinfo/libqmi-devel
> _______________________________________________
> libqmi-devel mailing list
> libqmi-devel at lists.freedesktop.org
> https://lists.freedesktop.org/mailman/listinfo/libqmi-devel