<div dir="ltr"><div><div><div><div><div><div><div><div>I changed the PDP#3 by AT+CGDCONT=3,"IP","we01.vzwstatic","0.0.0.0",0,0 </div>and network is attached and the AT+CGCONTRDP gives address </div>and i have this now [root@localhost ~]# qmicli -d /dev/cdc-wdm0 --wds-get-default-settings=3gpp Default settings retrieved: APN: 'we01.vzwstatic' PDP type: 'ipv4' Auth: 'none'[root@localhost ~]# qmi-network /dev/cdc-wdm0 start Loading profile at /etc/qmi-network.conf... APN: vzwinternet APN user: unset APN password: unset qmi-proxy: no Checking data format with 'qmicli -d /dev/cdc-wdm0 --wda-get-data-format '... Device link layer protocol retrieved: 802-3 Getting expected data format with 'qmicli -d /dev/cdc-wdm0 --get-expected-data-format'... Expected link layer protocol retrieved: 802-3 Device and kernel link layer protocol match: 802-3 Starting network with 'qmicli -d /dev/cdc-wdm0 --wds-start-network=apn='vzwinternet' --client-no-release-cid '... error: couldn't start network: QMI protocol error (64): '(null)' Saving state at /tmp/qmi-network-state-cdc-wdm0... (CID: 8) error: network start failed, no packet data handle Clearing state at /tmp/qmi-network-state-cdc-wdm0... [root@localhost ~]# </div>but qmi-network not working </div>and </div>and also i tried with th raw-ip mode i have this qmicli -d /dev/cdc-wdm0 --wds-start-network="apn=we01.vzwstatic,ip-type=4" --device-open-net="net-raw-ip|net-no-qos-header" --device-open-sync --client-no-release-cid error: couldn't open the QmiDevice: QMI protocol error (70): 'InvalidOperation' </div>is the problem related to the system </div>i use the centos 7 with kernel 3.10.5 and i used the new usbnet and qmi_wwan (from 4.9) and libqmi1.12.6 </div><div>if debian is more recommended or any distribution more than centos7 i will install t </div><div><div><div>It is really difficult </div><div>thanks for all your helps </div><div><div><div><div> </div></div></div></div></div></div></div><div class="gmail_extra"> <div class="gmail_quote">2017-01-23 23:02 GMT+01:00 heni wael <<a href="mailto:waelheni91@gmail.com" target="_blank">waelheni91@gmail.com</a>>: <blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex"><div dir="ltr"><div>Thanks Tang But I didnt want to connect with the ipv6 </div><div>i just need ipv4 address </div> Thanks </div><div class="HOEnZb"><div class="h5"><div class="gmail_extra"> <div class="gmail_quote">2017-01-23 22:55 GMT+01:00 Tang Nguyen <<a href="mailto:tang_nguyen@yahoo.com" target="_blank">tang_nguyen@yahoo.com</a>>: <blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">It doesn't work because APN of PDP#3 is different with the APN that you want to connect to network. Issue below command to get correct APN, which associates with your SIM card, and pass that APN to "qmicli connect" command. qmicli -d /dev/cdc-wdm0 --wds-get-default-settings=3gpp PS. You can use command: AT+CGPIAF=1 to show correct IPv6 format from AT+CGCINTRDP command --tang -------------------------------------------- On Mon, 1/23/17, heni wael <<a href="mailto:waelheni91@gmail.com" target="_blank">waelheni91@gmail.com</a>> wrote: Subject: Re: MC7354 with Verizon network To: "Sebastian Sjoholm" <<a href="mailto:sebastian.sjoholm@gmail.com" target="_blank">sebastian.sjoholm@gmail.com</a>>, <a href="mailto:libqmi-devel@lists.freedesktop.org" target="_blank">libqmi-devel@lists.freedesktop.org</a> Date: Monday, January 23, 2017, 4:34 PM <div><div class="m_-7643199322062035305h5"> OK now i have firmware installed and the network connected i try to use qmicli to do the LTE connection i have this AT OK AT!ENTERCND="A710" OK AT!UDUSBCOMP? !UDUSBCOMP: 6 OK AT!GOBIIMPREF ERROR AT!GOBIIMPREF? !GOBIIMPREF: preferred fw version: 05.05.58.01 preferred carrier name: VZW preferred config name: VZW_005.029_000 current fw version: 05.05.58.01 current carrier name: VZW current config name: VZW_005.029_000 OK And network connected i dont know if the PDP is Ok or not AT OK at!gstatus? !GSTATUS: Current Time: 203 Temperature: 33 Bootup Time: 5 Mode: ONLINE System mode: LTE PS state: Attached LTE band: B4 LTE bw: 10 MHz LTE Rx chan: 2100 LTE Tx chan: 20100 EMM state: Registered Normal Service RRC state: RRC Idle IMS reg state: Full Srv IMS mode: Normal RSSI (dBm): -54 Tx Power: 0 RSRP (dBm): -78 TAC: 2501 (9473) RSRQ (dB): -9 Cell ID: 0091A216 (9544214) SINR (dB): 3.6 OK AT+CGCONTRDP +CGCONTRDP: 1,5,vzwims,38.0.16.16.129.83.54.223.0.0.0.23.143.19.114.1, 254.128.0.0.0.0.0.0.0.0.0.23.143.19.114.64, 32.1.72.136.0.104.6 OK AT+CGDCONT? +CGDCONT: 1,"IPV4V6","vzwims","0.0.0.0",0,0 +CGDCONT: 2,"IPV4V6","vzwadmin","0.0.0.0",0,0 +CGDCONT: 3,"IPV4V6","vzwinternet","0.0.0.0",0,0 +CGDCONT: 4,"IPV4V6","vzwapp","0.0.0.0",0,0 +CGDCONT: 5,"IPV4V6","vzw800","0.0.0.0",0,0 +CGDCONT: 9,"IPV6","vzwims","0.0.0.0",0,0 +CGDCONT: 10,"IP","vzwadmin","0.0.0.0",0,0 +CGDCONT: 11,"IP","vzwinternet","0.0.0.0",0,0 +CGDCONT: 12,"IPV4V6","vzwapp","0.0.0.0",0,0 +CGDCONT: 13,"IP","","0.0.0.0",0,0 OK AT+CGATT? +CGATT: 1 OK but when i try to use the qmicli i got an error [root@localhost ~]# qmi-network /dev/cdc-wdm0 start Loading profile at /etc/qmi-network.conf... APN: we01.vzwstatic APN user: unset APN password: unset qmi-proxy: no Loading previous state from /tmp/qmi-network-state-cdc-wdm0... Previous CID: 1 Previous PDH: 1138072296 error: cannot re-start network, PDH already exists qmicli -d /dev/cdc-wdm0 --wds-get-current-settings [root@localhost ~]# qmicli -d /dev/cdc-wdm0 --wds-get-current-settings error: couldn't get current settings: QMI protocol error (15): 'OutOfCall' [root@localhost ~]# qmi-network /dev/cdc-wdm0 start Loading profile at /etc/qmi-network.conf... APN: we01.vzwstatic APN user: unset APN password: unset qmi-proxy: no Loading previous state from /tmp/qmi-network-state-cdc-wdm0... Previous CID: 1 Previous PDH: 1138072296 error: cannot re-start network, PDH already exists have you got an idea ? 2017-01-23 21:35 GMT+01:00 heni wael <<a href="mailto:waelheni91@gmail.com" target="_blank">waelheni91@gmail.com</a>>: Ok Thanks 2017-01-23 21:31 GMT+01:00 Sebastian Sjoholm <<a href="mailto:sebastian.sjoholm@gmail.com" target="_blank">sebastian.sjoholm@gmail.com</a>>: > On Jan 23, 2017, at 21:26 , heni wael <<a href="mailto:waelheni91@gmail.com" target="_blank">waelheni91@gmail.com</a>> wrote: > > [root@localhost ~]# cat /etc/modprobe.d/blacklist-mode m.conf > blacklist qcserial > blacklist qmi_wwan > blacklist usb_wwan > blacklist cdc_mbim > blacklist cdc_wdm > blacklist cdc_ncm > blacklist sierra > blacklist sierra_net > [root@localhost ~]# > That looks pretty OK, and the dmesg and lsusb -t shows that the qmi_wwan is still loaded after that? I can find a bunch of cases via google when the blacklist file is not loaded, but it is depended on what linux you are running, I think a google search for your system would be a good start. -Sebastian </div></div> -----Inline Attachment Follows----- <div class="m_-7643199322062035305HOEnZb"><div class="m_-7643199322062035305h5"> _______________________________________________ libqmi-devel mailing list <a href="mailto:libqmi-devel@lists.freedesktop.org" target="_blank">libqmi-devel@lists.freedesktop.org</a> <a href="https://lists.freedesktop.org/mailman/listinfo/libqmi-devel" rel="noreferrer" target="_blank">https://lists.freedesktop.org/mailman/listinfo/libqmi-devel</a> </div></div></blockquote></div> </div> </div></div></blockquote></div> </div>