[Mesa-dev] [PATCH 4/4] i965: Properly handle integer types in opt_vector_float().

[Kenneth Graunke]

Previously, opt_vector_float() always interpreted MOV sources as
floating point, and always created a MOV with a F-type destination.

This meant that we could mess up sequences of integer loads, such as:

   mov vgrf6.0.x:D, 0D
   mov vgrf6.0.y:D, 1D
   mov vgrf6.0.z:D, 2D
   mov vgrf6.0.w:D, 3D

Here, integer 0/1/2/3 become approximately 0.0f, so we generated:

   mov vgrf6.0:F, [0F, 0F, 0F, 0F]

which is clearly wrong.  We can properly handle this by converting
integer values to float (rather than bitcasting), and emitting a type
converting MOV:

   mov vgrf6.0:D, [0F, 1F, 2F, 3F]

To do this, see first see if the integer values (converted to float)
are representable.  If so, we use a D-type MOV.  If not, we then try
the floating point values and an F-type MOV.  We make zero not impose
type restrictions.  This is important because 0D would imply a D-type
MOV, but is often used in sequences such as MOV 0D, MOV 0x3f800000D,
where we want to use an F-type MOV.

Fixes about 54 dEQP-GLES2 failures with the vec4 VS backend.  This
recently became visible due to changes in opt_vector_float() which
made it optimize more cases, but it was a pre-existing bug.

Signed-off-by: Kenneth Graunke <kenneth at whitecape.org>
---
 src/mesa/drivers/dri/i965/brw_vec4.cpp | 24 ++++++++++++++++++++----
 1 file changed, 20 insertions(+), 4 deletions(-)

diff --git a/src/mesa/drivers/dri/i965/brw_vec4.cpp b/src/mesa/drivers/dri/i965/brw_vec4.cpp
index 12c3c66..2bdcf1f 100644
--- a/src/mesa/drivers/dri/i965/brw_vec4.cpp
+++ b/src/mesa/drivers/dri/i965/brw_vec4.cpp
@@ -361,9 +361,11 @@ vec4_visitor::opt_vector_float()
    int inst_count = 0;
    vec4_instruction *imm_inst[4];
    unsigned writemask = 0;
+   enum brw_reg_type dest_type = BRW_REGISTER_TYPE_F;
 
    foreach_block_and_inst_safe(block, vec4_instruction, inst, cfg) {
       int vf = -1;
+      enum brw_reg_type need_type;
 
       /* Look for unconditional MOVs from an immediate with a partial
        * writemask.  Skip type-conversion MOVs other than integer 0,
@@ -375,14 +377,26 @@ vec4_visitor::opt_vector_float()
           inst->predicate == BRW_PREDICATE_NONE &&
           inst->dst.writemask != WRITEMASK_XYZW &&
           (inst->src[0].type == inst->dst.type || inst->src[0].d == 0)) {
-         vf = brw_float_to_vf(inst->src[0].f);
+         vf = brw_float_to_vf(inst->src[0].d);
+         need_type = BRW_REGISTER_TYPE_D;
+
+         if (vf == -1) {
+            vf = brw_float_to_vf(inst->src[0].f);
+            need_type = BRW_REGISTER_TYPE_F;
+         }
+
+         /* Zero can be loaded as any type; don't impose a restriction. */
+         if (inst->src[0].d == 0)
+            need_type = dest_type;
       }
 
       /* If this wasn't a MOV, or the value was non-representable, or
-       * the destination register doesn't match, then this breaks our
-       * sequence.  Combine anything we've accumulated so far.
+       * the destination register doesn't match, or we have to switch
+       * destination types, then this breaks our sequence.  Combine
+       * anything we've accumulated so far.
        */
       if (vf == -1 ||
+          dest_type != need_type ||
           last_reg != inst->dst.nr ||
           last_reg_offset != inst->dst.reg_offset ||
           last_reg_file != inst->dst.file) {
@@ -391,7 +405,7 @@ vec4_visitor::opt_vector_float()
             unsigned vf;
             memcpy(&vf, imm, sizeof(vf));
             vec4_instruction *mov = MOV(imm_inst[0]->dst, brw_imm_vf(vf));
-            mov->dst.type = BRW_REGISTER_TYPE_F;
+            mov->dst.type = dest_type;
             mov->dst.writemask = writemask;
             inst->insert_before(block, mov);
 
@@ -405,6 +419,7 @@ vec4_visitor::opt_vector_float()
          inst_count = 0;
          last_reg = -1;
          writemask = 0;
+         dest_type = BRW_REGISTER_TYPE_F;
 
          for (int i = 0; i < 4; i++) {
             imm[i] = 0;
@@ -428,6 +443,7 @@ vec4_visitor::opt_vector_float()
          last_reg = inst->dst.nr;
          last_reg_offset = inst->dst.reg_offset;
          last_reg_file = inst->dst.file;
+         dest_type = need_type;
       }
    }
 
-- 
2.8.0