[Nouveau] [PATCH v2 2/2] connector: allow 225/297MHz pixel clocks for HDMI on Fermi/Kepler

Ilia Mirkin imirkin at alum.mit.edu
Tue Nov 3 17:54:05 PST 2015


Some Fermi's apparently alow allow 297MHz clocks, so create a parameter
which allows end-users to set it themselves until we have a reliable way
to determine the board's maximum pixel clocks.

Signed-off-by: Ilia Mirkin <imirkin at alum.mit.edu>
---
 drm/nouveau/nouveau_connector.c | 25 ++++++++++++++++++++++---
 1 file changed, 22 insertions(+), 3 deletions(-)

diff --git a/drm/nouveau/nouveau_connector.c b/drm/nouveau/nouveau_connector.c
index 4c8f6ef..57bea79 100644
--- a/drm/nouveau/nouveau_connector.c
+++ b/drm/nouveau/nouveau_connector.c
@@ -56,6 +56,10 @@ MODULE_PARM_DESC(duallink, "Allow dual-link TMDS (default: enabled)");
 int nouveau_duallink = 1;
 module_param_named(duallink, nouveau_duallink, int, 0400);
 
+MODULE_PARM_DESC(hdmimhz, "Force a maximum HDMI pixel clock (in MHz)");
+int nouveau_hdmimhz = 0;
+module_param_named(hdmimhz, nouveau_hdmimhz, int, 0400);
+
 struct nouveau_encoder *
 find_encoder(struct drm_connector *connector, int type)
 {
@@ -809,12 +813,23 @@ nouveau_connector_get_modes(struct drm_connector *connector)
 }
 
 static unsigned
-get_tmds_link_bandwidth(struct drm_connector *connector)
+get_tmds_link_bandwidth(struct drm_connector *connector, bool hdmi)
 {
 	struct nouveau_connector *nv_connector = nouveau_connector(connector);
 	struct nouveau_drm *drm = nouveau_drm(connector->dev);
 	struct dcb_output *dcb = nv_connector->detected_encoder->dcb;
 
+	if (hdmi) {
+		if (nouveau_hdmimhz > 0)
+			return nouveau_hdmimhz * 1000;
+		/* Note: these limits are conservative, some Fermi's
+		 * can do 297 MHz. Unclear how this can be determined.
+		 */
+		if (drm->device.info.family >= NV_DEVICE_INFO_V0_KEPLER)
+			return 297000;
+		if (drm->device.info.family >= NV_DEVICE_INFO_V0_FERMI)
+			return 225000;
+	}
 	if (dcb->location != DCB_LOC_ON_CHIP ||
 	    drm->device.info.chipset >= 0x46)
 		return 165000;
@@ -835,6 +850,7 @@ nouveau_connector_mode_valid(struct drm_connector *connector,
 	struct drm_encoder *encoder = to_drm_encoder(nv_encoder);
 	unsigned min_clock = 25000, max_clock = min_clock;
 	unsigned clock = mode->clock;
+	bool hdmi;
 
 	switch (nv_encoder->dcb->type) {
 	case DCB_OUTPUT_LVDS:
@@ -847,8 +863,11 @@ nouveau_connector_mode_valid(struct drm_connector *connector,
 		max_clock = 400000;
 		break;
 	case DCB_OUTPUT_TMDS:
-		max_clock = get_tmds_link_bandwidth(connector);
-		if (nouveau_duallink && nv_encoder->dcb->duallink_possible)
+		hdmi = !nv_connector->edid ||
+			drm_detect_hdmi_monitor(nv_connector->edid);
+		max_clock = get_tmds_link_bandwidth(connector, hdmi);
+		if (!hdmi && nouveau_duallink &&
+		    nv_encoder->dcb->duallink_possible)
 			max_clock *= 2;
 		break;
 	case DCB_OUTPUT_ANALOG:
-- 
2.4.10



More information about the Nouveau mailing list