[Nouveau] [RFC PATCH] pci: prevent putting pcie devices into lower device states on certain intel bridges

[Karol Herbst]

still happens with your patch applied. The machine simply gets shut down.

dmesg can be found here:
https://gist.githubusercontent.com/karolherbst/40eb091c7b7b33ef993525de660f1a3b/raw/2380e31f566e93e5ba7c87ef545420965d4c492c/gistfile1.txt

If there are no other things to try out, I will post the updated patch shortly.

On Mon, Sep 30, 2019 at 11:29 AM Mika Westerberg
<mika.westerberg at linux.intel.com> wrote:
>
> On Mon, Sep 30, 2019 at 11:15:48AM +0200, Karol Herbst wrote:
> > On Mon, Sep 30, 2019 at 10:05 AM Mika Westerberg
> > <mika.westerberg at linux.intel.com> wrote:
> > >
> > > Hi Karol,
> > >
> > > On Fri, Sep 27, 2019 at 11:53:48PM +0200, Karol Herbst wrote:
> > > > > What exactly is the serious issue?  I guess it's that the rescan
> > > > > doesn't detect the GPU, which means it's not responding to config
> > > > > accesses?  Is there any timing component here, e.g., maybe we're
> > > > > missing some delay like the ones Mika is adding to the reset paths?
> > > >
> > > > When I was checking up on some of the PCI registers of the bridge
> > > > controller, the slot detection told me that there is no device
> > > > recognized anymore. I don't know which register it was anymore, though
> > > > I guess one could read it up in the SoC spec document by Intel.
> > > >
> > > > My guess is, that the bridge controller fails to detect the GPU being
> > > > here or actively threw it of the bus or something. But a normal system
> > > > suspend/resume cycle brings the GPU back online (doing a rescan via
> > > > sysfs gets the device detected again)
> > >
> > > Can you elaborate a bit what kind of scenario the issue happens (e.g
> > > steps how it reproduces)? It was not 100% clear from the changelog. Also
> > > what the result when the failure happens?
> > >
> >
> > yeah, I already have an updated patch in the works which also does the
> > rework Bjorn suggested. Had no time yet to test if I didn't mess it
> > up.
> >
> > I am also thinking of adding a kernel parameter to enable this
> > workaround on demand, but not quite sure on that one yet.
>
> Right, I think it would be good to figure out the root cause before
> adding any workarounds ;-) It might very well be that we are just
> missing something the PCIe spec requires but not implemented in Linux.
>
> > > I see there is a script that does something but unfortunately I'm not
> > > fluent in Python so can't extract the steps how the issue can be
> > > reproduced ;-)
> > >
> > > One thing that I'm working on is that Linux PCI subsystem misses certain
> > > delays that are needed after D3cold -> D0 transition, otherwise the
> > > device and/or link may not be ready before we access it. What you are
> > > experiencing sounds similar. I wonder if you could try the following
> > > patch and see if it makes any difference?
> > >
> > > https://patchwork.kernel.org/patch/11106611/
> >
> > I think I already tried this path. The problem isn't that the device
> > isn't accessible too late, but that it seems that the device
> > completely falls off the bus. But I can retest again just to be sure.
>
> Yes, please try it and share full dmesg if/when the failure still happens.