[Openchrome-users] Slow 2d output
julius.junghans@gmx.de
julius.junghans
Sat Sep 16 09:54:33 PDT 2006
Am Freitag 15 September 2006 18:13 schrieb julius.junghans at gmx.de:
> Hi,
>
> ive just recently changed my laptop in favour of a via nehemiah 1,2 ghz.
> the 2d output is slow - for example i can see the screen repainting when
> scrolling sites in konqueror/konsole. even the output of top when it first
> starts up fills the screen in "slow motion"... On the other side watching
> xvid movies works fine.
> I guess this behavior is not normal?
>
>
> glxgears:
> 2265 frames in 5.0 seconds = 452.874 FPS
>
>
> /etc/X11/xorg.conf
> Section "Module"
> Load "glx"
> Load "extmod"
> Load "xtrap"
> Load "record"
> Load "dbe"
> Load "dri"
> Load "freetype"
> Load "type1"
> EndSection
> Section "Device"
> Identifier "Card0"
> Driver "via"
> VendorName "Unknown Vendor"
> BoardName "Unknown Board"
> BusID "PCI:1:0:0"
> Option "EnableAGPDMA" "true"
> EndSection
> Section "Screen"
> Identifier "Screen0"
> Device "Card0"
> Monitor "Monitor0"
> DefaultDepth 16
>
> Subsection "Display"
> Depth 16
> Modes "1280x1024" "1280x960" "1024x768" "800x600"
> EndSubSection
> EndSection
> Section "dri"
> Mode 0666
> EndSection
>
>
> cat /var/log/Xorg.0.log|grep VIA
> (II) VIA: driver for VIA chipsets: CLE266, KM400/KN400, K8M800,
> (!!) VIA Technologies does not support or endorse this driver in any way.
> (II) VIA(0): VIAPreInit
> (II) VIA(0): VIAGetRec
> (**) VIA(0): Depth 16, (--) framebuffer bpp 16
> (==) VIA(0): RGB weight 565
> (==) VIA(0): Default visual is TrueColor
> (**) VIA(0): Option "EnableAGPDMA" "true"
> (==) VIA(0): Using XAA acceleration architecture
> (==) VIA(0): Using HW cursor
> (**) VIA(0): Option: EnableAGPDMA - Enabling AGP DMA
> (--) VIA(0): Chipset: "CLE266"
> (II) VIA(0): VIAMapMMIO
> (--) VIA(0): mapping MMIO @ 0xe4000000 with size 0x9000
> (--) VIA(0): mapping BitBlt MMIO @ 0xe4200000 with size 0x10000
> (II) VIA(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp->PIOOffset is
> 0x0000 (--) VIA(0): Chipset Rev.: 18
> (WW) VIA(0): Manufacturer plainly copied main PCI ids to Subsystem/Card
> ids. (--) VIA(0): Detected VIA VT3122 (CLE266)-EPIA M/MII/....
> (II) VIA(0): Detected MemClk 4
> (II) VIA(0): ViaGetMemoryBandwidth
> (II) VIA(0): Detected TV Standard: NTSC.
> (==) VIA(0): Using gamma correction (1.0, 1.0, 1.0)
> (--) VIA(0): videoram = 32768k
> (II) VIA(0): ViaI2CInit
> (II) VIA(0): ViaI2CBus1Init
> (II) VIA(0): I2C bus "I2C bus 1" initialized.
> (II) VIA(0): ViaI2cBus2Init
> (II) VIA(0): I2C bus "I2C bus 2" initialized.
> (II) VIA(0): ViaI2CBus3Init
> (II) VIA(0): I2C bus "I2C bus 3" initialized.
> (II) VIA(0): I2C device "I2C bus 1:ddc2" registered at address 0xA0.
> (II) VIA(0): I2C device "I2C bus 1:ddc2" removed.
> (II) VIA(0): Manufacturer: MAX Model: 17bb Serial#: 5539
> (II) VIA(0): Year: 2003 Week: 43
> (II) VIA(0): EDID Version: 1.3
> (II) VIA(0): Analog Display Input, Input Voltage Level: 0.700/0.700 V
> (II) VIA(0): Sync: Separate
> (II) VIA(0): Max H-Image Size [cm]: horiz.: 36 vert.: 27
> (II) VIA(0): Gamma: 2.20
> (II) VIA(0): DPMS capabilities: Off; RGB/Color Display
> (II) VIA(0): First detailed timing is preferred mode
> (II) VIA(0): redX: 0.626 redY: 0.340 greenX: 0.288 greenY: 0.608
> (II) VIA(0): blueX: 0.148 blueY: 0.064 whiteX: 0.283 whiteY: 0.298
> (II) VIA(0): Supported VESA Video Modes:
> (II) VIA(0): 720x400 at 70Hz
> (II) VIA(0): 640x480 at 60Hz
> (II) VIA(0): 640x480 at 75Hz
> (II) VIA(0): 800x600 at 75Hz
> (II) VIA(0): 1024x768 at 75Hz
> (II) VIA(0): 1280x1024 at 75Hz
> (II) VIA(0): Manufacturer's mask: 0
> (II) VIA(0): Supported Future Video Modes:
> (II) VIA(0): #0: hsize: 640 vsize 480 refresh: 85 vid: 22833
> (II) VIA(0): #1: hsize: 800 vsize 600 refresh: 85 vid: 22853
> (II) VIA(0): #2: hsize: 1024 vsize 768 refresh: 85 vid: 22881
> (II) VIA(0): #3: hsize: 1280 vsize 1024 refresh: 85 vid: 39297
> (II) VIA(0): #4: hsize: 1600 vsize 1200 refresh: 75 vid: 20393
> (II) VIA(0): Supported additional Video Mode:
> (II) VIA(0): clock: 157.5 MHz Image Size: 360 x 270 mm
> (II) VIA(0): h_active: 1280 h_sync: 1344 h_sync_end 1504 h_blank_end 1728
> h_border: 0
> (II) VIA(0): v_active: 1024 v_sync: 1025 v_sync_end 1028 v_blanking: 1072
> v_border: 0
> (II) VIA(0): Monitor name: Belinea
> (II) VIA(0): Monitor name: 106075
> (II) VIA(0): Ranges: V min: 50 V max: 160 Hz, H min: 30 H max: 98 kHz,
> PixClock max 200 MHz
> (II) VIA(0): ViaOutputsDetect
> (II) VIA(0): VIATVDetect
> (II) VIA(0): ViaVT162xDetect
> (II) VIA(0): I2C device "I2C bus 2:VT162x" registered at address 0x40.
> (--) VIA(0): Detected VIA Technologies VT1622A/VT1623 TV Encoder
> (II) VIA(0): ViaTVInit
> (II) VIA(0): ViaVT162xInit
> (II) VIA(0): VT162xSave
> (II) VIA(0): VT1622DACSense
> (--) VIA(0): VT162x: Nothing connected.
> (II) VIA(0): ViaOutputsSelect
> (II) VIA(0): ViaOutputsSelect: X Configuration: 0x00
> (II) VIA(0): ViaOutputsSelect: BIOS Initialised register: 0x00
> (II) VIA(0): ViaOutputsSelect: CRT.
> (II) VIA(0): ViaModesAttach
> (II) VIA(0): Monitor0: Using hsync range of 30.00-98.00 kHz
> (II) VIA(0): Monitor0: Using vrefresh range of 50.00-160.00 Hz
>
> ...
> (--) VIA(0): Display dimensions: (360, 270) mm
> (--) VIA(0): DPI set to (90, 96)
> (II) VIA(0): VIAUnmapMem
> (II) VIA(0): VIAScreenInit
> (II) VIA(0): VIAMapFB
> (--) VIA(0): mapping framebuffer @ 0xe0000000 with size 0x2000000
> (==) VIA(0): Write-combining range (0xe0000000,0x2000000)
> (--) VIA(0): Frame buffer start: 0xb5ae9000, free start: 0x280000 end:
> 0x2000000
> (II) VIA(0): VIAMapMMIO
> (--) VIA(0): mapping MMIO @ 0xe4000000 with size 0x9000
> (--) VIA(0): mapping BitBlt MMIO @ 0xe4200000 with size 0x10000
> (II) VIA(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp->PIOOffset is
> 0x0000 (II) VIA(0): VIASave
> (II) VIA(0): VT162xSave
> (II) VIA(0): VIAWriteMode
> (II) VIA(0): ViaModePrimary
> (II) VIA(0): ViaModePrimaryVGA
> (II) VIA(0): ViaModePrimaryVGA: Setting up 1280x1024
> (II) VIA(0): CrtcHTotal: 0x6C0
> (II) VIA(0): CrtcHDisplay: 0x500
> (II) VIA(0): CrtcHBlankStart: 0x500
> (II) VIA(0): CrtcHBlankEnd: 0x6C0
> (II) VIA(0): CrtcHSyncStart: 0x540
> (II) VIA(0): CrtcHSyncEnd: 0x5E0
> (II) VIA(0): CrtcVTotal: 0x430
> (II) VIA(0): CrtcVDisplay: 0x400
> (II) VIA(0): CrtcVSyncStart: 0x401
> (II) VIA(0): CrtcVSyncEnd: 0x404
> (II) VIA(0): CrtcVBlankStart: 0x400
> (II) VIA(0): CrtcVBlankEnd: 0x430
> (II) VIA(0): Offset: 0x140
> (II) VIA(0): Fetch Count: 0x140
> (II) VIA(0): ViaComputeDotClock 157500 : 422c : 0216
> (II) VIA(0): ViaTVPower: Off.
> (II) VIA(0): VT1622Power
> (II) VIA(0): ViaSetPrimaryFIFO
> (II) VIA(0): ViaSetPrimaryExpireNumber
> (II) VIA(0): ViaSetPrimaryDotclock to 0x000216
> (II) VIA(0): ViaSetUseExternalClock
> (II) VIA(0): 3D Engine has been initialized.
> (II) VIA(0): VIAAdjustFrame
> (II) VIA(0): VIAAdjustFrame
> (II) VIA(0): - Blanked
> (II) VIA(0): [drm] DRM interface version 1.2
> (II) VIA(0): [drm] created "via" driver at busid "PCI:1:0:0"
> (II) VIA(0): [drm] added 8192 byte SAREA at 0xf8f45000
> (II) VIA(0): [drm] mapped SAREA 0xf8f45000 to 0xb5ae7000
> (II) VIA(0): [drm] framebuffer handle = 0xe0000000
> (II) VIA(0): [drm] added 1 reserved context for kernel
> (II) VIA(0): [dri] visual configs initialized.
> (II) VIA(0): [drm] register handle = 0xe4000000
> (II) VIA(0): [drm] framebuffer handle = 0xe0000000
> (II) VIA(0): [drm] mmio Registers = 0xe4000000
> (II) VIA(0): [dri] mmio mapped.
> (II) VIA(0): - Visuals set up
> (II) VIA(0): VIAInternalScreenInit
> (II) VIA(0): - B & W
> (II) VIA(0): Using 3072 lines for offscreen memory.
> (II) VIA(0): Using XFree86 Acceleration Architecture (XAA)
> (==) VIA(0): Backing store disabled
> (II) VIA(0): - Backing store set up
> (II) VIA(0): - SW cursor set up
> (II) VIA(0): VIAHWCursorInit
> (II) VIA(0): - Def Color map set up
> (II) VIA(0): VIALoadPalette
> (II) VIA(0): - Palette loaded
> (II) VIA(0): - DPMS set up
> (II) VIA(0): - Color maps etc. set up
> (EE) VIA(0): [drm] drmAgpAcquire failed 19
> (II) VIA(0): [dri] use pci.
> (II) VIA(0): [drm] Using 22797280 bytes for DRM memory heap.
> (II) VIA(0): [dri] frame buffer initialized.
> (II) VIA(0): X context handle = 0x1
> (II) VIA(0): [drm] installed DRM signal handler
> (II) VIA(0): [DRI] installation complete
> (II) VIA(0): [dri] kernel data initialized.
> (II) VIA(0): [drm] Irq handler installed, using IRQ 12.
> (EE) VIA(0): [drm] Failed to initialize DMA ring-buffer: 14
> (II) VIA(0): direct rendering enabled
> (II) VIA(0): [Xv] Using PCI DMA for Xv image transfer.
> (II) VIA(0): Benchmarking video copy. Less is better.
> (--) VIA(0): Timed libc YUV420 copy... 4023958. Throughput: 176.9 MiB/s.
> (--) VIA(0): Timed kernel YUV420 copy... 4198106. Throughput: 169.6 MiB/s.
> (--) VIA(0): Timed SSE YUV420 copy... 2417048. Throughput: 294.5 MiB/s.
> (--) VIA(0): Timed MMX YUV420 copy... 4062189. Throughput: 175.2 MiB/s.
> (--) VIA(0): Ditch 3DNow! YUV420 copy... Not supported by CPU.
> (--) VIA(0): Timed MMX2 YUV420 copy... 2566252. Throughput: 277.4 MiB/s.
> (--) VIA(0): Using SSE YUV42X copy for video.
> (II) VIA(0): [XvMC] Registering viaXvMC.
> (II) VIA(0): [XvMC] Initialized XvMC extension.
> (II) VIA(0): - Done
>
> _______________________________________________
> openchrome-users mailing list
> openchrome-users at openchrome.org
> http://wiki.openchrome.org/mailman/listinfo/openchrome-users
> Main page:
> http://www.openchrome.org
> Wiki:
> http://wiki.openchrome.org
> User Forum:
> http://wiki.openchrome.org/tikiwiki/tiki-view_forum.php?forumId=1
Missed a line in the syslog, the bios is set to 64mb shared memory
[drm:via_initialize] *ERROR* via_initialize called with no agp memory
available
This error is about the available ram right?
Julius
More information about the Openchrome-users
mailing list