[Openchrome-users] Questions from Argentina
Daniel Padula
paduladaniel
Fri Aug 3 11:09:54 PDT 2007
Hi!
I 'm from Argentina, sorry for my English... I have a PC-CHIPS
motherboard model P29G+ with VIA P4M890 chipset, I 've installed openchrome
SVN, with the kernel 2.6.22.1, and/or 2.6.21.1, first of all I try OpenArena
and it's worked excellent, but when y tried to watch TV from tvtime, It's
shows a green screen and whole X hang up, and the only way of continue is
restarting because I can't put X down... So, I thought that it was a capture
card problem, I took it out, and, the same problem... I opened the glxgears,
everything was good, but when I try to move the glxgears 's windows, began
to make some crazy movements, as if the window were duplicated... What
could be happening?
Thanks in advance!
This is the information of the board...
01:00.0 VGA compatible controller: VIA Technologies, Inc. Unknown device
3343 (rev 01) (prog-if 00 [VGA])
Subsystem: Elitegroup Computer Systems Unknown device 1629
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (500ns min)
Interrupt: pin A routed to IRQ 23
Region 0: Memory at a0000000 (32-bit, prefetchable) [size=512M]
Region 1: Memory at fd000000 (32-bit, non-prefetchable) [size=16M]
Expansion ROM at feaf0000 [disabled] [size=64K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [70] AGP version 3.0
Status: RQ=256 Iso- ArqSz=0 Cal=7 SBA+ ITACoh- GART64- HTrans-
64bit- FW- AGP3+ Rate=x4,x8
Command: RQ=8 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=x8
and my dmesg...
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 448076k/458368k available (1489k kernel code, 9716k reserved, 591k
data, 316k init, 0k highmem)
virtual kernel memory layout:
fixmap : 0xfffb7000 - 0xfffff000 ( 288 kB)
vmalloc : 0xdc800000 - 0xfffb5000 ( 567 MB)
lowmem : 0xc0000000 - 0xdbfa0000 ( 447 MB)
.init : 0xc030f000 - 0xc035e000 ( 316 kB)
.data : 0xc0274407 - 0xc03080e0 ( 591 kB)
.text : 0xc0100000 - 0xc0274407 (1489 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 3194.79 BogoMIPS
(lpj=1597397)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000
0000e39d 00000000 00000001
monitor/mwait feature present.
using mwait in idle threads.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 1024K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU: After all inits, caps: bfebfbff 20100000 00000000 00003940 0000e39d
00000000 00000001
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
Freeing SMP alternatives: 9k freed
ACPI: Core revision 20070126
CPU0: Intel Genuine Intel(R) CPU 2140 @ 1.60GHz stepping 02
Booting processor 1/1 eip 2000
Initializing CPU#1
Calibrating delay using timer specific routine.. 3191.56 BogoMIPS
(lpj=1595784)
CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000
0000e39d 00000000 00000001
monitor/mwait feature present.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 1024K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU: After all inits, caps: bfebfbff 20100000 00000000 00003940 0000e39d
00000000 00000001
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel Genuine Intel(R) CPU 2140 @ 1.60GHz stepping 02
Total of 2 processors activated (6386.36 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
checking TSC synchronization [CPU#0 -> CPU#1]: passed.
Brought up 2 CPUs
migration_cost=60
NET: Registered protocol family 16
EISA bus registered
ACPI: bus type pci registered
PCI: BIOS Bug: MCFG area at e0000000 is not E820-reserved
PCI: Not using MMCONFIG.
PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=3
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.NBPG._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.NBP0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs *3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11 12 14 15) *0,
disabled.
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0,
disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0,
disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0,
disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 *10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 15 devices
ACPI: ACPI bus type pnp unregistered
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a
report
pnp: 00:09: ioport range 0xa00-0xa0f has been reserved
pnp: 00:09: ioport range 0xa10-0xa1f has been reserved
pnp: 00:09: ioport range 0xa20-0xa2f has been reserved
pnp: 00:09: ioport range 0xa30-0xa3f has been reserved
pnp: 00:0a: iomem range 0xff380000-0xff3fffff has been reserved
pnp: 00:0b: iomem range 0xfec00000-0xfec00fff could not be reserved
pnp: 00:0b: iomem range 0xfee00000-0xfee00fff could not be reserved
pnp: 00:0d: iomem range 0xe0000000-0xefffffff has been reserved
pnp: 00:0e: iomem range 0x0-0x9ffff could not be reserved
pnp: 00:0e: iomem range 0xc0000-0xcffff could not be reserved
pnp: 00:0e: iomem range 0xe0000-0xfffff could not be reserved
pnp: 00:0e: iomem range 0x100000-0x1bffffff could not be reserved
Time: tsc clocksource has been installed.
PCI: Bridge: 0000:00:01.0
IO window: disabled.
MEM window: fca00000-feafffff
PREFETCH window: 9ff00000-dfefffff
PCI: Bridge: 0000:00:02.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:03.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Setting latency timer of device 0000:00:01.0 to 64
ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 27 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:02.0 to 64
ACPI: PCI Interrupt 0000:00:03.0[A] -> GSI 31 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:03.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 6, 262144 bytes)
TCP bind hash table entries: 16384 (order: 5, 196608 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
checking if image is initramfs...it isn't (bad gzip magic numbers); looks
like an initrd
Freeing initrd memory: 3032k freed
audit: initializing netlink socket (disabled)
audit(1186102367.385:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: VIA PCI bridge detected. Disabling DAC.
PCI: Bypassing VIA 8237 APIC De-Assert Message
Boot video device is 0000:01:00.0
PCI: Setting latency timer of device 0000:00:02.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:02.0:pcie00]
Allocate Port Service[0000:00:02.0:pcie02]
PCI: Setting latency timer of device 0000:00:03.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:03.0:pcie00]
Allocate Port Service[0000:00:03.0:pcie02]
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
mdacon: MDA with 8K of memory detected.
Console: switching consoles 1-16 to mono MDA-2 80x25
vesafb: framebuffer at 0xa0000000, mapped to 0xdc880000, using 3072k, total
65536k
vesafb: mode is 1024x768x16, linelength=2048, pages=41
vesafb: protected mode interface info at c000:7952
vesafb: pmi: set display start = c00c79a0, set palette = c00c7a11
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
vga16fb: initializing
vga16fb: mapped to 0xc00a0000
fb1: VGA16 VGA frame buffer device
fb2: Virtual frame buffer device, using 1024K of video memory
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input0
EISA: Probing bus 0 at eisa.0
EISA: Detected 0 cards.
TCP cubic registered
Starting balanced_irq
Using IPI Shortcut mode
Switched to high resolution mode on CPU 0
Switched to high resolution mode on CPU 1
input: ImExPS/2 Generic Explorer Mouse as /class/input/input1
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 3032KiB [1 disk] into ram disk...
|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/done.
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: 316k freed
Write protecting the kernel read-only data: 443k
SCSI subsystem initialized
libata version 2.21 loaded.
sata_via 0000:00:0f.0: version 2.2
ACPI: PCI Interrupt 0000:00:0f.0[B] -> GSI 20 (level, low) -> IRQ 18
sata_via 0000:00:0f.0: routed to hard irq line 3
scsi0 : sata_via
scsi1 : sata_via
ata1: SATA max UDMA/133 cmd 0x0001ec00 ctl 0x0001e882 bmdma 0x0001e400 irq
18
ata2: SATA max UDMA/133 cmd 0x0001e800 ctl 0x0001e482 bmdma 0x0001e408 irq
18
ata1: SATA link down 1.5 Gbps (SStatus 0 SControl 300)
ata2: SATA link down 1.5 Gbps (SStatus 0 SControl 300)
NET: Registered protocol family 1
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:0f.1
ACPI: PCI Interrupt 0000:00:0f.1[A] -> GSI 20 (level, low) -> IRQ 18
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1
ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
hda: WDC WD1600BB-55RDA0, ATA DISK drive
hdb: TSSTcorpCD/DVDW SH-S182F, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
Probing IDE interface ide1...
hda: max request size: 512KiB
hda: 312581808 sectors (160041 MB) w/2048KiB Cache, CHS=19457/255/63,
UDMA(100)
hda: cache flushes supported
hda: hda1 hda2 hda3 < hda5 hda6 >
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
Linux agpgart interface v0.102 (c) Dave Jones
agpgart: Detected VIA P4M890 chipset
agpgart: AGP aperture is 128M @ 0xf0000000
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
Linux video capture interface: v2.00
input: PC Speaker as /class/input/input2
Real Time Clock Driver v1.12ac
parport_pc 00:08: reported by Plug and Play ACPI
parport0: PC-style at 0x378 (0x778), irq 7, dma 3
[PCSPP,TRISTATE,COMPAT,ECP,DMA]
ACPI: PCI Interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 19
ehci_hcd 0000:00:10.4: EHCI Host Controller
ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:10.4: irq 19, io mem 0xfebff800
ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
hdb: ATAPI 48X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
via-rhine.c:v1.10-LK1.4.3 2007-03-06 Written by Donald Becker
USB Universal Host Controller Interface driver v3.0
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
ungrab_winmodem: version magic '2.6.22.1 SMP preempt mod_unload PENTIUM4 '
should be '2.6.22.1 SMP preempt mod_unload CORE2 '
ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 19
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.0: irq 19, io base 0x0000dc00
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
slamr: version magic '2.6.22.1 SMP preempt mod_unload PENTIUM4 ' should be '
2.6.22.1 SMP preempt mod_unload CORE2 '
00:0c: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ACPI: PCI Interrupt 0000:00:10.1[A] -> GSI 21 (level, low) -> IRQ 19
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.1: irq 19, io base 0x0000d880
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
saa7130/34: v4l2 driver version 0.2.14 loaded
ACPI: PCI Interrupt 0000:00:10.2[B] -> GSI 21 (level, low) -> IRQ 19
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:10.2: irq 19, io base 0x0000d800
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.3[B] -> GSI 21 (level, low) -> IRQ 19
uhci_hcd 0000:00:10.3: UHCI Host Controller
uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:10.3: irq 19, io base 0x0000d480
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 23 (level, low) -> IRQ 20
eth0: VIA Rhine II at 0xfebff400, 00:19:21:1a:30:97, IRQ 20.
eth0: MII PHY found at address 1, status 0x786d advertising 05e1 Link 45e1.
ACPI: PCI Interrupt 0000:00:11.6[C] -> GSI 22 (level, low) -> IRQ 21
PCI: Setting latency timer of device 0000:00:11.6 to 64
ACPI: PCI Interrupt 0000:00:11.5[C] -> GSI 22 (level, low) -> IRQ 21
PCI: Setting latency timer of device 0000:00:11.5 to 64
ACPI: PCI Interrupt 0000:00:09.0[A] -> GSI 17 (level, low) -> IRQ 22
saa7134[0]: found at 0000:00:09.0, rev: 1, irq: 22, latency: 64, mmio:
0xfebffc00
saa7134[0]: subsystem: 17de:7128, board: UNKNOWN/GENERIC
[card=0,autodetected]
saa7134[0]: board init: gpio is c0407f
saa7134[0]: i2c eeprom 00: de 17 28 71 10 28 ff ff ff ff ff ff ff ff ff ff
saa7134[0]: i2c eeprom 10: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7134[0]: i2c eeprom 20: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7134[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7134[0]: i2c eeprom 40: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7134[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7134[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7134[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7134[0]: registered device video0 [v4l2]
saa7134[0]: registered device vbi0
Adding 506008k swap on /dev/hda5. Priority:-1 extents:1 across:506008k
EXT3 FS on hda6, internal journal
loop: module loaded
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised:
dm-devel at redhat.com
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
ACPI Warning (tbutils-0158): Incorrect checksum in table [OEMB] - 6E,
should be 61 [20070126]
ACPI: SSDT 1BFAE0B0, 01D2 (r1 AMI CPU1PM 1 INTL 20051117)
ACPI: Processor [CPU1] (supports 16 throttling states)
ACPI: SSDT 1BFAE290, 0143 (r1 AMI CPU2PM 1 INTL 20051117)
ACPI: Processor [CPU2] (supports 16 throttling states)
lp0: using parport0 (interrupt-driven).
lp0: console ready
ppdev: user-space parallel port driver
eth4: link up, 100Mbps, full-duplex, lpa 0x45E1
NET: Registered protocol family 17
[drm] Initialized drm 1.1.0 20060810
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 23
[drm] Initialized via 2.11.1 20070202 on minor 0
agpgart: Found an AGP 3.5 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode
Thanks again...
Daniel
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://wiki.openchrome.org/pipermail/openchrome-users/attachments/20070803/12d77f76/attachment-0001.html
More information about the Openchrome-users
mailing list