[pulseaudio-discuss] [PATCH v3 1/2] refactor default sink/source handling

[Georg Chini]

On 12.03.2017 23:07, Tanu Kaskinen wrote:
> On Sun, 2017-03-12 at 16:45 +0100, Georg Chini wrote:
>> On 16.02.2017 11:09, Tanu Kaskinen wrote:
>>
>> "Refactor" is the wrong word, you are changing the logic.
>> Maybe redesign is a better verb.
> Indeed. I think I'll change it to "improve" ("redesign" feels a bit
> strong).
>
>>> Currently the default sink policy is simple: either the user has
>>> configured it explicitly, in which case we always use that as the
>>> default, or we pick the sink with the highest priority. The sink
>>> priorities are currently static, so there's no need to worry about
>>> updating the default sink when sink priorities change.
>>>
>>> I intend to make things a bit more complex: if the active port of a sink
>>> is unavailable, the sink should not be the default sink, and I also want
>>> to make sink priorities dependent on the active port, so changing the
>>> port should cause re-evaluation of which sink to choose as the default.
>>> Currently the default sink choice is done only when someone calls
>>> pa_namereg_get_default_sink(), and change notifications are only sent
>>> when a sink is created or destroyed. That makes it hard to add new rules
>>> to the default sink selection policy.
>>>
>>> This patch moves the default sink selection to
>>> pa_core_update_default_sink(), which is called whenever something
>>> happens that can affect the default sink choice. That function needs to
>>> know the previous choice in order to send change notifications as
>>> appropriate, but previously pa_core.default_sink was only set when the
>>> user had configured it explicitly. Now pa_core.default_sink is always
>>> set (unless there are no sinks at all), so pa_core_update_default_sink()
>>> can use that to get the previous choice. The user configuration is saved
>>> in a new variable, pa_core.configured_default_sink.
>>>
>>> pa_namereg_get_default_sink() is now unnecessary, because
>>> pa_core.default_sink can be used directly to get the
>>> currently-considered-best sink. pa_namereg_set_default_sink() is
>>> replaced by pa_core_set_configured_default_sink().
>> It seems a bit strange to me, that module-default-device-restore and
>> module-switch-on-connect set the configured_default_* variables, because
>> these should be the user configured values.
>> If a user has configured his default sink/source,
>> module-switch-on-connect will change
>> it if some new device (for example a bluetooth headset) turns up. This
>> is then saved
>> as the new default sink/source, so the original user setting is lost and
>> on the next start
>> of pulseaudio, it will use the (possibly not existent) device as the
>> default.
>> It also means, that if there is no user configured value, it suddenly
>> will be there
>> because module-default-device-restore saves the current default as the
>> user default.
> I don't think this is a regression. I tried to make as few behavioural
> changes as possible. I'm aware that module-default-device-restore needs
> to be improved, which requires changes in the core too. Basically, I
> think configured_default_sink should be the sink name (a string) so
> that it can remain set even when the configured sink is not present.

Yes, it is no regression. But anyway, while you are improving it, I
would use a string for the user configured sink as you say and also
save the user configured value and the current value. When pulseaudio
is restarted you can check if the last used default sink is still available
and if not use the user default.
That change could however be done in a separate patch.

>
>> I would use two variables, user_configured_default_* and
>> system_configured_default_*
>> and let module-default-device-restore save both values. When loading the
>> configuration,
>> the module can check if the system configured default still exists and
>> else revert to
>> the user setting. Module-switch-on-connect would use the system_ variables.
>> The system_configured_default_* variables would take the role of the current
>> configured_default_* variables and the user_configured_default_*
>> variables would
>> only get copied into them if the sink/source is valid.
>>
>> This would also mean, that the user can configure any value for the
>> default, if the
>> sink or source does not exist, it won't be used. The user configured
>> value will
>> also survive any temporary changes done by module-switch-on-connect.
> I acknowledge that it feels a bit weird to have module-switch-on-
> connect set a variable that's supposed to be set by the user, but
> again, this is not a regression, and I'm not convinced that there is
> any better alternative.

It is not a regression, but it is done wrong in the current code.
I proposed the alternative to have two variables so that the user
setting will not be forgotten.

>
> Regarding your proposal, you didn't specify in detail how the system
> and user default devices are supposed to be prioritized. When a device
> is plugged in, we certainly want to override the user's previous
> configuration, which would suggest prioritizing the system default over
> the user default. But if the user then manually selects some other
> device as the default, that should override the system default. If the
> rule is "whichever was set last wins", then we lose no information by
> folding the two variables into a single default device variable.

"Whichever was set last wins" looks good to me. With the current code
you definitely lose the information what the user configured, that is
why it bothers me that the value is overwritten. Consider the following
case:
You have a system with sinks A and B where A has higher priority and
the user has chosen B as default.
If you now connect a new device, the default sink will change to it.
If you disconnect the device again, the system will go to sink A and not
to B as the user configured, because the user setting has been
overwritten.
I think that is definitely wrong behavior and needs fixing. (What's even
worse, if you have module-default-device-restore loaded, it will present
sink A as the user choice if pulseaudio is restarted at this point.)


>
>>> +void pa_core_set_configured_default_sink(pa_core *core, pa_sink *sink) {
>>> +    pa_sink *old_sink;
>>> +
>>> +    pa_assert(core);
>>> +
>>> +    old_sink = core->configured_default_sink;
>> Why do you use a new variable here? If you move the assignment after
>> the pa_log_info() the variable is not necessary. This also applies to a few
>> other functions.
> I find the extra variable to make the code a bit clearer. I don't feel
> very strongly about this, though, so if it bothers you, I can change
> it.

I don't really see how it makes things clearer, but I also don't mind 
keeping
it if you prefer.