<div dir="ltr">Hi All.I have a problem with hsp profile. After connect to Philips WeCall Speaker profile headset_head_unit is available: Card #2 Name: bluez_card.0C_A6_94_25_70_DE Driver: module-bluez5-device.c Owner Module: 25 Properties: device.description = "Philips WeCall Speaker" device.string = "0C:A6:94:25:70:DE" device.api = "bluez" device.class = "sound" device.bus = "bluetooth" device.form_factor = "headset" bluez.path = "/org/bluez/hci1/dev_0C_A6_94_25_70_DE" bluez.class = "0x240404" bluez.alias = "Philips WeCall Speaker" device.icon_name = "audio-headset-bluetooth" device.intended_roles = "phone" Profiles: headset_head_unit: Headset Head Unit (HSP/HFP) (sinks: 1, sources: 1, priority: 20, available: yes a2dp_sink: High Fidelity Playback (A2DP Sink) (sinks: 1, sources: 0, priority: 10, available: yes) device.description = "Philips WeCall Speaker" off: Off (sinks: 0, sources: 0, priority: 0, available: yes) Active Profile: headset_head_unit Ports: headset-output: Headset (priority: 0, latency offset: 0 usec) Part of profile(s): headset_head_unit, a2dp_sink headset-input: Headset (priority: 0, latency offset: 0 usec) Part of profile(s): headset_head_unit I set default sink and source. After run ‘mplayer test.wav’ nothing is happens (there is no sound). In a2dp_sink profile everything works fine, but I need use microphone to record voice. I run hcidump:[root@localhost ~]# hcidump -i hci1 -XHCI sniffer - Bluetooth packet analyzer ver 2.5device: hci1 snap_len: 1500 filter: 0xffffffff< HCI Command: Exit Sniff Mode (0x02|0x0004) plen 2 handle 13> HCI Event: Command Status (0x0f) plen 4 Exit Sniff Mode (0x02|0x0004) status 0x00 ncmd 1> HCI Event: Mode Change (0x14) plen 6 status 0x00 handle 13 mode 0x00 interval 0 Mode: Active< HCI Command: Setup Synchronous Connection (0x01|0x0028) plen 17 handle 13 voice setting 0x0060 ptype 0x003f> HCI Event: Command Status (0x0f) plen 4 Setup Synchronous Connection (0x01|0x0028) status 0x00 ncmd 1> HCI Event: Synchronous Connect Complete (0x2c) plen 17 status 0x00 handle 6 bdaddr 0C:A6:94:25:70:DE type eSCO Air mode: CVSD< SCO data: handle 6 flags 0x00 dlen 48 0000: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ 0010: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ 0020: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................< SCO data: handle 6 flags 0x00 dlen 48 0000: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ 0010: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ 0020: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................< HCI Command: Disconnect (0x01|0x0006) plen 3 handle 6 reason 0x13 Reason: Remote User Terminated Connection> HCI Event: Command Status (0x0f) plen 4 Disconnect (0x01|0x0006) status 0x00 ncmd 1> HCI Event: Disconn Complete (0x05) plen 4 status 0x00 handle 6 reason 0x16 Reason: Connection Terminated by Local Host My controller - is a BCM4354 chip[bluetooth]# showController C0:97:27:4C:2E:67 Name: ARTIK10 Alias: ARTIK10 Class: 0x0c0408 Powered: yes Discoverable: no Pairable: yes UUID: Headset AG (00001112-0000-1000-8000-00805f9b34fb) UUID: Generic Attribute Profile (00001801-0000-1000-8000-00805f9b34fb) UUID: A/V Remote Control (0000110e-0000-1000-8000-00805f9b34fb) UUID: Generic Access Profile (00001800-0000-1000-8000-00805f9b34fb) UUID: PnP Information (00001200-0000-1000-8000-00805f9b34fb) UUID: A/V Remote Control Target (0000110c-0000-1000-8000-00805f9b34fb) UUID: Audio Source (0000110a-0000-1000-8000-00805f9b34fb) UUID: Audio Sink (0000110b-0000-1000-8000-00805f9b34fb) Modalias: usb:v1D6Bp0246d0524 Discovering: no My device:[Philips WeCall Speaker]# info 0C:A6:94:25:70:DEDevice 0C:A6:94:25:70:DE Name: Philips WeCall Speaker Alias: Philips WeCall Speaker Class: 0x240404 Icon: audio-card Paired: yes Trusted: yes Blocked: no Connected: yes LegacyPairing: no UUID: Headset (00001108-0000-1000-8000-00805f9b34fb) UUID: Audio Sink (0000110b-0000-1000-8000-00805f9b34fb) UUID: A/V Remote Control Target (0000110c-0000-1000-8000-00805f9b34fb) UUID: Advanced Audio Distribu.. (0000110d-0000-1000-8000-00805f9b34fb) UUID: A/V Remote Control (0000110e-0000-1000-8000-00805f9b34fb) UUID: Handsfree (0000111e-0000-1000-8000-00805f9b34fb) pulseaudio log[root@localhost audio]# journalctl -b 0 | grep -i pulseOct 09 16:10:26 localhost systemd[1]: Started pulseaudio service.Oct 09 16:10:26 localhost systemd[1]: Starting pulseaudio service...Oct 09 16:10:26 localhost pulseaudio[3416]: W: [pulseaudio] main.c: Running in system mode, but --disallow-module-loading not set!Oct 09 16:10:26 localhost pulseaudio[3416]: N: [pulseaudio] main.c: Running in system mode, forcibly disabling SHM mode!Oct 09 16:10:26 localhost pulseaudio[3416]: W: [pulseaudio] main.c: OK, so you are running PA in system mode. Please note that you most likely shouldn't be doing that.Oct 09 16:10:26 localhost pulseaudio[3416]: W: [pulseaudio] main.c: If you do it nonetheless then it's your own fault if things don't work as expected.Oct 09 16:10:26 localhost pulseaudio[3416]: W: [pulseaudio] main.c: Please read <a href="http://www.freedesktop.org/wiki/Software/PulseAudio/Documentation/User/WhatIsWrongWithSystemWide/">http://www.freedesktop.org/wiki/Software/PulseAudio/Documentation/User/WhatIsWrongWithSystemWide/</a> for an explanation why system mode is usually a bad idea.Oct 09 16:10:27 localhost kernel: [c6] lpass_set_sched: [pulseaudio] pid = 3416, prio = 49Oct 09 16:10:27 localhost kernel: [c1] lpass_set_sched: [pulseaudio] pid = 3416, prio = 49Oct 09 16:10:27 localhost kernel: [c1] lpass_set_sched: [pulseaudio] pid = 3416, prio = 49Oct 09 16:10:27 localhost kernel: [c1] lpass_set_sched: [pulseaudio] pid = 3416, prio = 49Oct 09 16:10:27 localhost kernel: [c1] lpass_set_sched: [pulseaudio] pid = 3416, prio = 49Oct 09 16:10:27 localhost kernel: [c1] lpass_set_sched: [pulseaudio] pid = 3416, prio = 49Oct 09 16:10:27 localhost kernel: [c1] lpass_set_sched: [pulseaudio] pid = 3416, prio = 49Oct 09 16:10:27 localhost kernel: [c1] lpass_set_sched: [pulseaudio] pid = 3416, prio = 49Oct 09 16:10:27 localhost kernel: [c1] lpass_set_sched: [pulseaudio] pid = 3416, prio = 49Oct 09 16:10:27 localhost kernel: [c1] lpass_set_sched: [pulseaudio] pid = 3416, prio = 49Oct 09 16:10:27 localhost kernel: [c1] lpass_set_sched: [pulseaudio] pid = 3416, prio = 49Oct 09 16:10:27 localhost kernel: [c1] lpass_set_sched: [pulseaudio] pid = 3416, prio = 49Oct 09 16:10:27 localhost kernel: [c1] lpass_set_sched: [pulseaudio] pid = 3416, prio = 49Oct 09 16:10:27 localhost kernel: [c1] lpass_set_sched: [pulseaudio] pid = 3416, prio = 49Oct 09 16:10:27 localhost kernel: [c1] lpass_set_sched: [pulseaudio] pid = 3416, prio = 49Oct 09 16:10:27 localhost kernel: [c1] lpass_set_sched: [pulseaudio] pid = 3416, prio = 49Oct 09 16:10:27 localhost kernel: [c1] lpass_set_sched: [pulseaudio] pid = 3416, prio = 49Oct 09 16:10:27 localhost kernel: [c1] lpass_set_sched: [pulseaudio] pid = 3416, prio = 49Oct 09 16:10:27 localhost pulseaudio[3416]: W: [pulseaudio] authkey.c: Failed to open cookie file '/var/run/pulse/.config/pulse/cookie': No such file or directoryOct 09 16:10:27 localhost pulseaudio[3416]: W: [pulseaudio] authkey.c: Failed to load authentication key '/var/run/pulse/.config/pulse/cookie': No such file or directoryOct 09 16:10:27 localhost pulseaudio[3416]: W: [pulseaudio] authkey.c: Failed to open cookie file '/var/run/pulse/.pulse-cookie': No such file or directoryOct 09 16:10:27 localhost pulseaudio[3416]: W: [pulseaudio] authkey.c: Failed to load authentication key '/var/run/pulse/.pulse-cookie': No such file or directory [root@localhost audio]# journalctl -b 0 | grep -i blueOct 09 16:10:24 localhost kernel: [c6] Bluetooth: Core ver 2.16Oct 09 16:10:24 localhost kernel: [c6] Bluetooth: HCI device and connection manager initializedOct 09 16:10:24 localhost kernel: [c6] Bluetooth: HCI socket layer initializedOct 09 16:10:24 localhost kernel: [c6] Bluetooth: L2CAP socket layer initializedOct 09 16:10:24 localhost kernel: [c6] Bluetooth: SCO socket layer initializedOct 09 16:10:24 localhost kernel: [c5] Bluetooth: Generic Bluetooth SDIO driver ver 0.1Oct 09 16:10:25 localhost kernel: [c0] bcm4354_bluetooth bluetooth.8: bcm4354_bluetooth_probe.Oct 09 16:10:25 localhost kernel: [c2] [BT] Bluetooth Power On.Oct 09 16:10:25 localhost kernel: [c5] bcm4354_bluetooth bluetooth.8: bcm4354_bluetooth_probe EndOct 09 16:10:25 localhost kernel: [c7] [BT] Bluetooth Power On.Oct 09 16:10:26 localhost dbus-daemon[3403]: Unknown username "bluealsa" in message bus configuration fileOct 09 16:10:26 localhost kernel: [c6] [BT] Bluetooth Power On.Oct 09 16:10:26 localhost systemd[1]: Starting BCM4354 Bluetooth firmware service...Oct 09 16:10:27 localhost fwdown.sh[3423]: /etc/bluetooth /Oct 09 16:10:27 localhost dbus[3403]: [system] Activating via systemd: service name='org.bluez' unit='dbus-org.bluez.service'Oct 09 16:10:27 localhost systemd[1]: Started BCM4354 Bluetooth firmware service.Oct 09 16:10:27 localhost systemd[1]: Starting Bluetooth service...Oct 09 16:10:27 localhost bluetoothd[3555]: Bluetooth daemon 5.36Oct 09 16:10:27 localhost dbus[3403]: [system] Successfully activated service 'org.bluez'Oct 09 16:10:27 localhost bluetoothd[3555]: Starting SDP serverOct 09 16:10:27 localhost systemd[1]: Started Bluetooth service.Oct 09 16:10:27 localhost kernel: [c0] Bluetooth: BNEP (Ethernet Emulation) ver 1.3Oct 09 16:10:27 localhost kernel: [c0] Bluetooth: BNEP filters: protocol multicastOct 09 16:10:27 localhost kernel: [c0] Bluetooth: BNEP socket layer initializedOct 09 16:10:27 localhost bluetoothd[3555]: Bluetooth management interface 1.3 initializedOct 09 16:10:27 localhost connmand[3419]: Method "ListAdapters" with signature "" on interface "org.bluez.Manager" doesn't existOct 09 16:10:27 localhost kernel: [c3] Bluetooth: HCI UART driver ver 2.2Oct 09 16:10:27 localhost kernel: [c3] Bluetooth: HCI H4 protocol initializedOct 09 16:10:27 localhost kernel: [c3] Bluetooth: HCI BCSP protocol initializedOct 09 16:10:27 localhost kernel: [c3] Bluetooth: HCILL protocol initializedOct 09 16:10:27 localhost kernel: [c3] Bluetooth: HCIATH3K protocol initializedOct 09 16:10:27 localhost kernel: [c3] Bluetooth: HCI Three-wire UART (H5) protocol initializedOct 09 16:10:27 localhost bluetoothd[3555]: Failed to obtain handles for "Service Changed" characteristicOct 09 16:10:27 localhost systemd[1]: Reached target Bluetooth.Oct 09 16:10:27 localhost systemd[1]: Starting Bluetooth.Oct 09 16:10:27 localhost kernel: [c0] Bluetooth: RFCOMM TTY layer initializedOct 09 16:10:27 localhost kernel: [c0] Bluetooth: RFCOMM socket layer initializedOct 09 16:10:27 localhost kernel: [c0] Bluetooth: RFCOMM ver 1.11Oct 09 16:10:27 localhost bluetoothd[3555]: hci1 Load Connection Parameters failed: Unknown Command (0x01)Oct 09 16:10:28 localhost bluetoothd[3555]: Endpoint registered: sender=:1.5 path=/MediaEndpoint/A2DPSourceOct 09 16:10:28 localhost bluetoothd[3555]: Endpoint registered: sender=:1.5 path=/MediaEndpoint/A2DPSink [root@localhost audio]# pulseaudio --versionpulseaudio 6.0 [root@localhost audio]# bluetoothctl --version5.36 I checked many different configuration. The last one is:--[root@localhost audio]# cat /etc/bluetooth/audio.conf# Configuration file for the audio service # This section contains options which are not specific to any# particular interface[General] # Switch to master role for incoming connections (defaults to true)Master=true # If we want to disable support for specific services# Defaults to supporting all implemented services#Disable=Gateway,Source,Socket#Disable=Gateway#Enable=Headset#Enable=Gateway,Source,SocketEnable=Source,Sink,Media,Socket,Headset#Enable=Source # SCO routing. Either PCM or HCI (in which case audio is routed to/from ALSA)# Defaults to HCI#SCORouting=PCM # Automatically connect both A2DP and HFP/HSP profiles for incoming# connections. Some headsets that support both profiles will only connect the# other one automatically so the default setting of true is usually a good# idea.AutoConnect=true # Headset interface specific options (i.e. options which affect how the audio# service interacts with remote headset devices)[Headset] # Set to true to support HFP, false means only HSP is supported# Defaults to trueHFP=false # Maximum number of connected HSP/HFP devices per adapter. Defaults to 1MaxConnected=1 # Set to true to enable use of fast connectable mode (faster page scanning)# for HFP when incoming call starts. Default settings are restored after# call is answered or rejected. Page scan interval is much shorter and page# scan type changed to interlaced. Such allows faster connection initiated# by a headset.FastConnectable=true # Just an example of potential config options for the other interfaces[A2DP]SBCSources=1MPEG12Sources=0 --[root@localhost audio]# cat /etc/pulse/<a href="http://system.pa">system.pa</a>#!/usr/bin/pulseaudio -nF## This file is part of PulseAudio.## PulseAudio is free software; you can redistribute it and/or modify it# under the terms of the GNU Lesser General Public License as published by# the Free Software Foundation; either version 2 of the License, or# (at your option) any later version.## PulseAudio is distributed in the hope that it will be useful, but# WITHOUT ANY WARRANTY; without even the implied warranty of# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU# General Public License for more details.## You should have received a copy of the GNU Lesser General Public License# along with PulseAudio; if not, see <<a href="http://www.gnu.org/licenses/">http://www.gnu.org/licenses/</a>>. # This startup script is used only if PulseAudio is started per-user# (i.e. not in system mode) .nofail ### Load something into the sample cache#load-sample-lazy x11-bell /usr/share/sounds/freedesktop/stereo/bell.oga#load-sample-lazy pulse-hotplug /usr/share/sounds/freedesktop/stereo/device-added.oga#load-sample-lazy pulse-coldplug /usr/share/sounds/freedesktop/stereo/device-added.oga#load-sample-lazy pulse-access /usr/share/sounds/freedesktop/stereo/message.oga .fail ### Automatically restore the volume of streams and devicesload-module module-device-restoreload-module module-stream-restoreload-module module-card-restore ### Automatically augment property information from .desktop files### stored in /usr/share/applicationload-module module-augment-properties ### Should be after module-*-restore but before module-*-detectload-module module-switch-on-port-available ### Load audio drivers statically### (it's probably better to not load these drivers manually, but instead### use module-udev-detect -- see below -- for doing this automatically)#load-module module-alsa-sink#load-module module-alsa-source device=hw:1,0#load-module module-null-sink#load-module module-pipe-sink ### Automatically load driver modules depending on the hardware available.ifexists module-udev-detect.soload-module module-udev-detect tsched=0.else### Use the static hardware detection module (for systems that lack udev support)load-module module-detect.endif ### Automatically connect sink and source if JACK server is present.ifexists module-jackdbus-detect.so.nofailload-module module-jackdbus-detect channels=2.fail.endif ### Automatically load driver modules for Bluetooth hardware.ifexists module-bluetooth-policy.soload-module module-bluetooth-policy.endif .ifexists module-bluetooth-discover.soload-module module-bluetooth-discover##headset=native.endif ### Load several protocols.ifexists module-esound-protocol-unix.soload-module module-esound-protocol-unix.endifload-module module-native-protocol-unix ### Network access (may be configured with paprefs, so leave this commented### here if you plan to use paprefs)#load-module module-esound-protocol-tcp#load-module module-native-protocol-tcp#load-module module-zeroconf-publish ### Load the RTP receiver module (also configured via paprefs, see above)#load-module module-rtp-recv ### Load the RTP sender module (also configured via paprefs, see above)#load-module module-null-sink sink_name=rtp format=s16be channels=2 rate=44100 sink_properties="device.description='RTP Multicast Sink'"#load-module module-rtp-send source=rtp.monitor ### Load additional modules from GConf settings. This can be configured with the paprefs tool.### Please keep in mind that the modules configured by paprefs might conflict with manually### loaded modules..ifexists module-gconf.so.nofailload-module module-gconf.fail.endif ### Automatically restore the default sink/source when changed by the user### during runtime### NOTE: This should be loaded as early as possible so that subsequent modules### that look up the default sink/source get the right valueload-module module-default-device-restore ### Automatically move streams to the default sink if the sink they are### connected to dies, similar for sourcesload-module module-rescue-streams ### Make sure we always have a sink around, even if it is a null sink.load-module module-always-sink ### Honour intended role device propertyload-module module-intended-roles ### Automatically suspend sinks/sources that become idle for too longload-module module-suspend-on-idle ### If autoexit on idle is enabled we want to make sure we only quit### when no local session needs us anymore..ifexists module-console-kit.so#load-module module-console-kit.endif.ifexists module-systemd-login.soload-module module-systemd-login.endif ### Enable positioned event soundsload-module module-position-event-sounds ### Cork music/video streams when a phone stream is activeload-module module-role-cork ### Modules to allow autoloading of filters (such as echo cancellation)### on demand. module-filter-heuristics tries to determine what filters### make sense, and module-filter-apply does the heavy-lifting of### loading modules and rerouting streams.load-module module-filter-heuristicsload-module module-filter-apply # X11 modules should not be started from <a href="http://default.pa">default.pa</a> so that one daemon# can be shared by multiple sessions. ### Load X11 bell module#load-module module-x11-bell sample=x11-bell ### Register ourselves in the X11 session manager#load-module module-x11-xsmp ### Publish connection data in the X11 root window#.ifexists module-x11-publish.so#.nofail#load-module module-x11-publish#.fail#.endif ### Make some devices default#set-default-sink output#set-default-source inputload-module module-switch-on-connect ###load-module module-loopback ---[root@localhost audio]# cat /etc/pulse/daemon.conf# This file is part of PulseAudio.## PulseAudio is free software; you can redistribute it and/or modify# it under the terms of the GNU Lesser General Public License as published by# the Free Software Foundation; either version 2 of the License, or# (at your option) any later version.## PulseAudio is distributed in the hope that it will be useful, but# WITHOUT ANY WARRANTY; without even the implied warranty of# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU# General Public License for more details.## You should have received a copy of the GNU Lesser General Public License# along with PulseAudio; if not, see <<a href="http://www.gnu.org/licenses/">http://www.gnu.org/licenses/</a>>. ## Configuration file for the PulseAudio daemon. See pulse-daemon.conf(5) for## more information. Default values are commented out. Use either ; or # for## commenting. ; daemonize = no; fail = yes; allow-module-loading = yes; allow-exit = yes; use-pid-file = yes; system-instance = no; local-server-type = user; enable-shm = yes; shm-size-bytes = 0 # setting this 0 will use the system-default, usually 64 MiB; lock-memory = no; cpu-limit = no ; high-priority = yes; nice-level = -11 ; realtime-scheduling = yes; realtime-priority = 5 exit-idle-time = -1; scache-idle-time = 20 ; dl-search-path = (depends on architecture) ; load-default-script-file = yes; default-script-file = /etc/pulse/<a href="http://default.pa">default.pa</a> ; log-target = auto; log-level = notice; log-meta = no; log-time = no; log-backtrace = 0 ; resample-method = speex-float-1enable-remixing = yesenable-lfe-remixing = no; resample-methon = ffmpeg; flat-volumes = yes ; rlimit-fsize = -1; rlimit-data = -1; rlimit-stack = -1; rlimit-core = -1; rlimit-as = -1; rlimit-rss = -1; rlimit-nproc = -1; rlimit-nofile = 256; rlimit-memlock = -1; rlimit-locks = -1; rlimit-sigpending = -1; rlimit-msgqueue = -1; rlimit-nice = 31; rlimit-rtprio = 9; rlimit-rttime = 200000 default-sample-format = s16ledefault-sample-rate = 44100; alternate-sample-rate = 48000default-sample-channels = 2; default-channel-map = front-left,front-right default-fragments = 10default-fragment-size-msec = 10 ; enable-deferred-volume = yes; deferred-volume-safety-margin-usec = 8000; deferred-volume-extra-delay-usec = 0 </div>