Trouble with latest modesetting branch on G965
Jesse Barnes
jbarnes at virtuousgeek.org
Thu Sep 28 17:41:53 PDT 2006
I pulled down the lateset intel driver tree and checked out the
modesetting branch. The driver recognizes my chip now, but won't
set a mode on my widescreen display. The last part of the log is
shown below. Am I doing something wrong or is this branch not
fully cooked yet?
Thanks,
Jesse
(II) I810(0): initializing int10
(WW) I810(0): Bad V_BIOS checksum
(II) I810(0): Primary V_BIOS segment is: 0xc000
(II) I810(0): VESA BIOS detected
(II) I810(0): Integrated Graphics Chipset: Intel(R) 965G
(--) I810(0): Chipset: "965G"
(--) I810(0): Linear framebuffer at 0x40000000
(--) I810(0): IO registers at addr 0x50300000
(II) I810(0): 2 display pipes available.
(II) I810(0): detected 7932 kB stolen memory.
(WW) I810(0): Detected stolen memory (7872 kB) doesn't match what the BIOS reports (7616 kB)
(II) I810(0): Kernel reported 236800 total, 1 used
(II) Loading /usr/lib64/xorg/modules/libddc.so
(II) Module ddc: vendor="X.Org Foundation"
compiled for 7.1.1, module version = 1.0.0
(II) Loading /usr/lib64/xorg/modules/libi2c.so
(II) Module i2c: vendor="X.Org Foundation"
compiled for 7.1.1, module version = 1.2.0
(II) I810(0): I2C bus "CRTDDC_A" initialized.
(II) I810(0): I2C bus "SDVOCTRL_E" initialized.
(II) I810(0): I2C device "SDVOCTRL_E:SDVO Controller B" registered at address 0x70.
(II) I810(0): I2C bus "SDVOB DDC Bus" initialized.
SDVO: W: 02 (SDVO_CMD_GET_DEVICE_CAPS)
SDVO: R: 04 AA 03 01 01 01 01 00 (Success)
(II) I810(0): SDVO device VID/DID: 04:AA.03, 01, output 1: Y, output 2: N
(II) I810(0): I2C device "SDVOCTRL_E:SDVO Controller C" registered at address 0x72.
(II) I810(0): I2C bus "SDVOC DDC Bus" initialized.
SDVO: W: 02 (SDVO_CMD_GET_DEVICE_CAPS)
SDVO: R: 04 AA 03 01 01 01 01 00 (Success)
(II) I810(0): SDVO device VID/DID: 04:AA.03, 01, output 1: Y, output 2: N
(II) I810(0): I2C device "CRTDDC_A:ddc2" registered at address 0xA0.
(II) I810(0): I2C device "CRTDDC_A:ddc2" removed.
(EE) I810(0): DDC Analog 0, 00005010
(II) I810(0): I2C device "SDVOB DDC Bus:ddc2" registered at address 0xA0.
SDVO: W: 7A 02 (SDVO_CMD_SET_CONTROL_BUS_SWITCH)
SDVO: W: 7A 02 (SDVO_CMD_SET_CONTROL_BUS_SWITCH)
(EE) I810(0): Unable to write to SDVOCTRL_E Slave 112.
SDVO: W: 7A 02 (SDVO_CMD_SET_CONTROL_BUS_SWITCH)
SDVO: W: 7A 02 (SDVO_CMD_SET_CONTROL_BUS_SWITCH)
(EE) I810(0): Unable to write to SDVOCTRL_E Slave 112.
SDVO: W: 7A 02 (SDVO_CMD_SET_CONTROL_BUS_SWITCH)
SDVO: W: 7A 02 (SDVO_CMD_SET_CONTROL_BUS_SWITCH)
(EE) I810(0): Unable to write to SDVOCTRL_E Slave 112.
SDVO: W: 7A 02 (SDVO_CMD_SET_CONTROL_BUS_SWITCH)
SDVO: W: 7A 02 (SDVO_CMD_SET_CONTROL_BUS_SWITCH)
(EE) I810(0): Unable to write to SDVOCTRL_E Slave 112.
SDVO: W: 7A 02 (SDVO_CMD_SET_CONTROL_BUS_SWITCH)
SDVO: W: 7A 02 (SDVO_CMD_SET_CONTROL_BUS_SWITCH)
(EE) I810(0): Unable to write to SDVOCTRL_E Slave 112.
(II) I810(0): I2C device "SDVOB DDC Bus:ddc2" removed.
(EE) I810(0): DDC SDVO 1, 008F6A00
(II) I810(0): Manufacturer: DEL Model: a017 Serial#: 827208275
(II) I810(0): Year: 2006 Week: 28
(II) I810(0): EDID Version: 1.3
(II) I810(0): Digital Display Input
(II) I810(0): Max H-Image Size [cm]: horiz.: 52 vert.: 33
(II) I810(0): Gamma: 2.20
(II) I810(0): DPMS capabilities: StandBy Suspend Off; RGB/Color Display
(II) I810(0): Default color space is primary color space
(II) I810(0): First detailed timing is preferred mode
(II) I810(0): redX: 0.640 redY: 0.330 greenX: 0.300 greenY: 0.600
(II) I810(0): blueX: 0.150 blueY: 0.060 whiteX: 0.312 whiteY: 0.329
(II) I810(0): Supported VESA Video Modes:
(II) I810(0): 720x400 at 70Hz
(II) I810(0): 640x480 at 60Hz
(II) I810(0): 640x480 at 75Hz
(II) I810(0): 800x600 at 60Hz
(II) I810(0): 800x600 at 75Hz
(II) I810(0): 1024x768 at 60Hz
(II) I810(0): 1024x768 at 75Hz
(II) I810(0): 1280x1024 at 75Hz
(II) I810(0): Manufacturer's mask: 0
(II) I810(0): Supported Future Video Modes:
(II) I810(0): #0: hsize: 1280 vsize 1024 refresh: 60 vid: 32897
(II) I810(0): #1: hsize: 1600 vsize 1200 refresh: 60 vid: 16553
(II) I810(0): #2: hsize: 1152 vsize 864 refresh: 75 vid: 20337
(II) I810(0): #3: hsize: 1680 vsize 1050 refresh: 60 vid: 179
(II) I810(0): Supported additional Video Mode:
(II) I810(0): clock: 154.0 MHz Image Size: 519 x 324 mm
(II) I810(0): h_active: 1920 h_sync: 1968 h_sync_end 2000 h_blank_end 2080 h_border: 0
(II) I810(0): v_active: 1200 v_sync: 1203 v_sync_end 1209 v_blanking: 1235 v_border: 0
(II) I810(0): Serial No: CC30267E1N2S
(II) I810(0): Monitor name: DELL 2407WFP
(II) I810(0): Ranges: V min: 56 V max: 76 Hz, H min: 30 H max: 83 kHz, PixClock max 170 MHz
(II) I810(0): EDID (in hex):
(II) I810(0): 00ffffffffffff0010ac17a053324e31
(II) I810(0): 1c10010380342178eeee91a3544c9926
(II) I810(0): 0f5054a54b008180a940714fb3000101
(II) I810(0): 010101010101283c80a070b023403020
(II) I810(0): 360007442100001a000000ff00434333
(II) I810(0): 3032363745314e325320000000fc0044
(II) I810(0): 454c4c20323430375746500a000000fd
(II) I810(0): 00384c1e5311000a20202020202000ca
(II) I810(0): I2C device "SDVOC DDC Bus:ddc2" registered at address 0xA0.
SDVO: W: 7A 02 (SDVO_CMD_SET_CONTROL_BUS_SWITCH)
SDVO: W: 7A 02 (SDVO_CMD_SET_CONTROL_BUS_SWITCH)
SDVO: W: 7A 02 (SDVO_CMD_SET_CONTROL_BUS_SWITCH)
SDVO: W: 7A 02 (SDVO_CMD_SET_CONTROL_BUS_SWITCH)
(II) I810(0): I2C device "SDVOC DDC Bus:ddc2" removed.
(EE) I810(0): DDC SDVO 2, 008F6B40
(II) I810(0): Using hsync ranges from config file
(II) I810(0): Using vrefresh ranges from config file
(II) I810(0): Printing DDC gathered Modelines:
(II) I810(0): Found BDB block type 254
(II) I810(0): Found BDB block type 1
(II) I810(0): Found BDB block type 254
(II) I810(0): Found BDB block type 2
(II) I810(0): Found BDB block type 4
(II) I810(0): Found BDB block type 254
(II) I810(0): Found BDB block type 6
(II) I810(0): Found BDB block type 7
(II) I810(0): Found BDB block type 8
(II) I810(0): Found BDB block type 10
(II) I810(0): Found BDB block type 11
(II) I810(0): Found BDB block type 12
(II) I810(0): Found BDB block type 14
(II) I810(0): Found BDB block type 15
(II) I810(0): Found BDB block type 17
(II) I810(0): Found BDB block type 18
(II) I810(0): Found BDB block type 20
(II) I810(0): Found BDB block type 22
(II) I810(0): Found BDB block type 23
(II) I810(0): Found BDB block type 24
(II) I810(0): Found BDB block type 25
(II) I810(0): Found BDB block type 26
SDVO: W: 0B (SDVO_CMD_GET_ATTACHED_DISPLAYS)
SDVO: R: 01 00 01 00 01 00 01 00 (Success)
SDVO: W: 0B (SDVO_CMD_GET_ATTACHED_DISPLAYS)
SDVO: R: 00 00 00 00 00 00 00 00 (Success)
(--) I810(0): Pre-allocated VideoRAM: 7932 kByte
(==) I810(0): VideoRAM: 65536 kByte
(==) I810(0): video overlay key set to 0x101fe
(**) I810(0): page flipping disabled
(==) I810(0): Using gamma correction (1.0, 1.0, 1.0)
Executing (ax == 0x5f01) BIOS call at i830_driver.c:500
(II) I810(0): BIOS Build: 1371
(II) I810(0): Currently active displays on Pipe A:
(II) I810(0): DFP (digital flat panel)
(II) I810(0): No active displays on Pipe B.
(==) I810(0): Display is using Pipe A
(--) I810(0): Maximum frambuffer space: 65368 kByte
(--) I810(0): Maximum space available for video modes: 7616 kByte
(II) I810(0): I2C device "SDVOC DDC Bus:ddc2" registered at address 0xA0.
SDVO: W: 7A 02 (SDVO_CMD_SET_CONTROL_BUS_SWITCH)
SDVO: W: 7A 02 (SDVO_CMD_SET_CONTROL_BUS_SWITCH)
SDVO: W: 7A 02 (SDVO_CMD_SET_CONTROL_BUS_SWITCH)
SDVO: W: 7A 02 (SDVO_CMD_SET_CONTROL_BUS_SWITCH)
(II) I810(0): I2C device "SDVOC DDC Bus:ddc2" removed.
SDVO: W: 0B (SDVO_CMD_GET_ATTACHED_DISPLAYS)
SDVO: R: 00 00 00 00 00 00 00 00 (Success)
(II) I810(0): Printing probed modes for pipe 0
(II) I810(0): I2C device "CRTDDC_A:ddc2" registered at address 0xA0.
(II) I810(0): I2C device "CRTDDC_A:ddc2" removed.
(II) I810(0): Printing probed modes for pipe 1
Fatal server error:
No modes found on either pipe
More information about the xorg
mailing list