Cross compilation error in X11R6.7.0

[Mughilan Ramajayam]

Hi Shyjumon,

It sounds like you need to install new locale. I haven't faced such, so would suggest googling or posting the same again here in Xorg, changing the Subject line. I hope you could get help from other Xorg members too. Few good resources could pop-up.

Regarding the display, you need to figure out whether you have installed the appropriate display driver or a framebuffer driver (in case, you use a framebuffer device). And also set the display environment variable.

Regards,
Mughilan

"Shyjumon N." <shyjumon.n at ttec.soc-soft.com> wrote:     RE: Cross compilation error in X11R6.7.0     Hi Mughilan Ramajayam, JM Ibanez and group,
   Thanks for the support ..
 I have cross compiled gtk libraries with Tinyx back end for arm board and able to
  cross compile my application with the same.
 But when i am running the application on board i am getting the following error... please read the following.. any clues why the application is crashing...
 
 [root at localhost hello]# file TESTAPP_XHTL
 TESTAPP_XHTL: ELF 32-bit LSB executable, ARM, version 1 (ARM), for GNU/Linux 2.0.0, dynamically linked (uses shared libs), not stripped
 
 
 The error message in the board.... when the application is crashing is as follows...
 (TESTAPP_XHTL:68): Gdk-WARNING **: locale not supported by Xlib
 
 (TESTAPP_XHTL:68): Gdk-WARNING **: cannot set locale modifiers
 
 (TESTAPP_XHTL:68): Gtk-WARNING **: cannot open display:
 
 Thanks for the help.
 
 With regds,
 
 
 
 Shyjumon N
 Mobile: +91-9945006965
 
 
 
 -----Original Message-----
 From: Mughilan Ramajayam [mailto:mughirp at yahoo.com]
 Sent: Wed 3/28/2007 7:51 AM
 To: Shyjumon N.
 Cc: jm at orangeandbronze.com; mughirp at yahoo.com; xorg at lists.freedesktop.org
 Subject: Re: Cross compilation error in X11R6.7.0
 
 Two FP models cannot be mixed. Please check your toolchain.
 
 - Mughilan.R
 
 JM Ibanez <jm at orangeandbronze.com> wrote: "Shyjumon N."  writes:
 
 > Dear Mughilan Ramajayam,
 >    Thanks for your help.
 > I have ft2build.h in my include path and also i have installed freetype.
 > Let me show you my error while that i am getting while cross compiling fontconfig.
 > Please read the following. Something related to hardwarefp and softwarefp i am not sure about this things.
 > arm-linux-gcc -shared  .libs/fcatomic.o .libs/fcblanks.o .libs/fccache.o .libs/fccfg.o .libs/fccharset.o .libs/fcdbg.o .libs/fcdefault.o .libs/fcdir.o .libs/
 > fcfreetype.o .libs/fcfs.o .libs/fcinit.o .libs/fclang.o .libs/fclist.o .libs/fcmatch.o .libs/fcmatrix.o .libs/fcname.o .libs/fcpat.o .libs/fcstr.o .libs/fcxml.o
 > .libs/ftglue.o  -L/opt/tinyx-gtk/lib /opt/tinyx-gtk/lib/libfreetype.a -lz  -Wl,-soname -Wl,libfontconfig.so.1 -o .libs/libfontconfig.so.1.0.4
 > /root/crslib/arm/3.3.1/bin/../lib/gcc-lib/arm-linux/3.3.2/../../../../arm-linux/bin/ld: ERROR: /root/crslib/arm/3.3.1/bin/../lib/gcc-lib/arm-linux/3.3.2/crtendS.o
 > uses FPA instructions, whereas .libs/libfontconfig.so.1.0.4 does not
 > /root/crslib/arm/3.3.1/bin/../lib/gcc-lib/arm-linux/3.3.2/../../../../arm-linux/bin/ld: ERROR: /root/crslib/arm/3.3.1/bin/../lib/gcc-lib/arm-linux/3.3.2/crtendS.o
 > uses hardware FP, whereas .libs/libfontconfig.so.1.0.4 uses software FP
 > File format not recognized: failed to merge target specific data of file /root/crslib/arm/3.3.1/bin/../lib/gcc-lib/arm-linux/3.3.2/crtendS.o
 > /root/crslib/arm/3.3.1/bin/../lib/gcc-lib/arm-linux/3.3.2/../../../../arm-linux/bin/ld: ERROR: /root/crslib/arm/3.3.1/bin/../lib/gcc-lib/arm-linux/3.3.2/../../../..
 > /arm-linux/lib/crtn.o uses FPA instructions, whereas .libs/libfontconfig.so.1.0.4 does not
 > /root/crslib/arm/3.3.1/bin/../lib/gcc-lib/arm-linux/3.3.2/../../../../arm-linux/bin/ld: ERROR: /root/crslib/arm/3.3.1/bin/../lib/gcc-lib/arm-linux/3.3.2/../../../..
 > /arm-linux/lib/crtn.o uses hardware FP, whereas .libs/libfontconfig.so.1.0.4 uses software FP
 > File format not recognized: failed to merge target specific data of file /root/crslib/arm/3.3.1/bin/../lib/gcc-lib/arm-linux/3.3.2/../../../../arm-linux/lib/crtn.o
 > collect2: ld returned 1 exit status
 > gmake[2]: *** [libfontconfig.la] Error 1
 > gmake[2]: Leaving directory `/root/softwares/tinyx_gtk+res/fontconfig-2.3.93/src'
 > gmake[1]: *** [all-recursive] Error 1
 > gmake[1]: Leaving directory `/root/softwares/tinyx_gtk+res/fontconfig-2.3.93'
 > gmake: *** [all] Error 2
 
 FP --> floating point maybe?
 
 One side of the code is using floating-point assembly instructions,
 while another side is using software emulation or an incompatible
 floating-point instructions set.
 
 
 --
 JM Ibanez
 Senior Software Engineer
 Orange & Bronze Software Labs, Ltd. Co.
 
 jm at orangeandbronze.com
 http://software.orangeandbronze.com/
 
 
 
 ---------------------------------
 Now that's room service! Choose from over 150,000 hotels
 in 45,000 destinations on Yahoo! Travel to find your fit.
 
  
  

 
---------------------------------
Don't pick lemons.
See all the new 2007 cars at Yahoo! Autos.
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.x.org/archives/xorg/attachments/20070401/d22d5166/attachment.html>