[PATCH v2 1/2] drm/mipi-dsi: add (LPM) Low Power Mode transfer support

[Andrzej Hajda]

On 07/29/2014 02:57 AM, YoungJun Cho wrote:
> Hi Andrzej,
>
> On 07/29/2014 01:09 AM, Andrzej Hajda wrote:
>> On 07/28/2014 04:00 AM, Inki Dae wrote:
>>> This patch adds below two flags for LPM transfer, and it attaches LPM flags
>>> to a msg in accordance with master's mode_flags set by LCD Panel driver.
>>>
>>> MIPI_DSI_MODE_CMD_LPM
>>> - If this flag is set by Panel driver, MIPI-DSI controller will tranfer
>>> command data to Panel device in Low Power Mode.
>> What do you mean by command data? It could be:
>> - all transfer in command mode of operations,
>> - transfer initialized by the driver by writing to DSIM registers.
> The 2nd one.
>
>>> MIPI_DSI_MODE_VIDEO_LPM
>>> - If this flag is set by Panel driver, MIPI-DSI controller will tranfer
>>> image data to Panel device in Low Power Mode.
>> What is the meaning of this flag in case of command mode of operation?
> I'm also not sure that there is a case to transfer image data in Low 
> Power Mode, but this flag is not related with 'command mode' only.
> Inki may consider generic condition.
>
>> Maybe it would be better to create flags based on source of data/FIFOs:
>> - commands send by SFR registers,
>> - commands generated from data sent from Display Controller.
>>
>>
>>> And above two flags can be combined together to transfer command and video
>>> data to Panel device.
>>>
>>> MIPI DSI spec says,
>>>       "the host processor controls the desired mode of clock operation.
>>>        Host protocol and applications control Clock Lane operating mode
>>>        (High Speed or Low Power mode). System designers are responsible
>>>        for understanding the clock requirements for peripherals attached
>>>        to DSI and controlling clock behavior in accordance with those
>>>        requirements."
>>>
>>> Some LCD Panel devices, nt35502a, would need LPM transfer support
>>> because they should receive some initial commands with LPM by default
>>> hardware setting.
>>
>> Is this requirement for initial commands, or for all commands.
>> Btw what is the mode of operation of nt35502a? What flags do you need
>> for it?
>>
> The nt35502a panel is video(RGB) mode panel and it requires low power 
> mode for initial commands, which means to initialize nt35502a panel, the 
> initial commands are transferred by LP mode(Not HS mode).
> And after initialization, its other features like gamma control or etc 
> could be controlled in HS mode.

It sounds similar to my tc358764 bridge driver [1]. The difference is that
it uses only MIPI_DSI_GENERIC_LONG_(WRITE|READ) in LPM.

As I understand nt35502a requires also different driving of
TxRequestHSClk signal
and this seems to me unrelated to LPM. As LPM is not related at all with
HS clock, AFAIK.

Regards
Andrzej

[1]: http://permalink.gmane.org/gmane.linux.drivers.devicetree/61559


>
> Thank you.
> Best regards YJ
>
>>
>>> Changelog v2: just add more descriptions.
>>>
>>> Signed-off-by: Inki Dae <inki.dae at samsung.com>
>>> Acked-by: Kyungmin Park <kyungmin.park at samsung.com>
>>> ---
>>>   drivers/gpu/drm/drm_mipi_dsi.c |    3 +++
>>>   include/drm/drm_mipi_dsi.h     |    4 ++++
>>>   2 files changed, 7 insertions(+)
>>>
>>> diff --git a/drivers/gpu/drm/drm_mipi_dsi.c b/drivers/gpu/drm/drm_mipi_dsi.c
>>> index e633df2..6b2bbda 100644
>>> --- a/drivers/gpu/drm/drm_mipi_dsi.c
>>> +++ b/drivers/gpu/drm/drm_mipi_dsi.c
>>> @@ -232,6 +232,9 @@ int mipi_dsi_dcs_write(struct mipi_dsi_device *dsi, unsigned int channel,
>>>   		break;
>>>   	}
>>>
>>> +	if (dsi->mode_flags & MIPI_DSI_MODE_CMD_LPM)
>>> +		msg.flags = MIPI_DSI_MSG_USE_LPM;
>>> +
>>>   	return ops->transfer(dsi->host, &msg);
>>>   }
>> Shouldn't this be also the same for dcs read?
>>
>> Anyway I think check in the DSIM should be used instead, as panel driver
>> can issue other dsi transfers without MIPI_DSI_MSG_USE_LPM flag set.
>>
>> Regards
>> Andrzej
>>
>>
>>>   EXPORT_SYMBOL(mipi_dsi_dcs_write);
>>> diff --git a/include/drm/drm_mipi_dsi.h b/include/drm/drm_mipi_dsi.h
>>> index 944f33f..1c41e49 100644
>>> --- a/include/drm/drm_mipi_dsi.h
>>> +++ b/include/drm/drm_mipi_dsi.h
>>> @@ -94,6 +94,10 @@ void mipi_dsi_host_unregister(struct mipi_dsi_host *host);
>>>   #define MIPI_DSI_MODE_VSYNC_FLUSH	BIT(8)
>>>   /* disable EoT packets in HS mode */
>>>   #define MIPI_DSI_MODE_EOT_PACKET	BIT(9)
>>> +/* command low power mode */
>>> +#define MIPI_DSI_MODE_CMD_LPM		BIT(10)
>>> +/* video low power mode */
>>> +#define MIPI_DSI_MODE_VIDEO_LPM		BIT(11)
>>>
>>>   enum mipi_dsi_pixel_format {
>>>   	MIPI_DSI_FMT_RGB888,
>>>
>> _______________________________________________
>> dri-devel mailing list
>> dri-devel at lists.freedesktop.org
>> http://lists.freedesktop.org/mailman/listinfo/dri-devel
>>
>