[PATCH 22/22] arm64: dts: apq8016-sbc: Add HDMI display support

[Archit Taneja]

The APQ8016-sbc provides a HDMI output. The APQ8016 display block only
provides a MIPI DSI output. So, the board has a ADV7533 DSI to HDMI
encoder chip that sits between the DSI PHY output and the HDMI
connector.

Add the ADV7533 DT node under its I2C control bus, and tie the DSI
output port to the ADV7533's input port.

Cc: Andy Gross <andy.gross at linaro.org>
Cc: Rob Herring <robh at kernel.org>
Cc: devicetree at vger.kernel.org

Signed-off-by: Archit Taneja <architt at codeaurora.org>
---
 arch/arm64/boot/dts/qcom/apq8016-sbc-soc-pins.dtsi | 48 +++++++++++++
 arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi          | 82 ++++++++++++++++++++++
 2 files changed, 130 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/apq8016-sbc-soc-pins.dtsi b/arch/arm64/boot/dts/qcom/apq8016-sbc-soc-pins.dtsi
index ee828a8..e1e6c6b 100644
--- a/arch/arm64/boot/dts/qcom/apq8016-sbc-soc-pins.dtsi
+++ b/arch/arm64/boot/dts/qcom/apq8016-sbc-soc-pins.dtsi
@@ -24,4 +24,52 @@
 			bias-pull-up;
 		};
 	};
+
+	adv7533_int_active: adv533_int_active {
+		pinmux {
+			function = "gpio";
+			pins = "gpio31";
+		};
+		pinconf {
+			pins = "gpio31";
+			drive-strength = <16>;
+			bias-disable;
+		};
+	};
+
+	adv7533_int_suspend: adv7533_int_suspend {
+		pinmux {
+			function = "gpio";
+			pins = "gpio31";
+		};
+		pinconf {
+			pins = "gpio31";
+			drive-strength = <2>;
+			bias-disable;
+		};
+	};
+
+	adv7533_switch_active: adv7533_switch_active {
+		pinmux {
+			function = "gpio";
+			pins = "gpio32";
+		};
+		pinconf {
+			pins = "gpio32";
+			drive-strength = <16>;
+			bias-disable;
+		};
+	};
+
+	adv7533_switch_suspend: adv7533_switch_suspend {
+		pinmux {
+			function = "gpio";
+			pins = "gpio32";
+		};
+		pinconf {
+			pins = "gpio32";
+			drive-strength = <2>;
+			bias-disable;
+		};
+	};
 };
diff --git a/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi b/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi
index 205ef89..5045695 100644
--- a/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi
+++ b/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi
@@ -59,6 +59,47 @@
 		/* On High speed expansion */
 			label = "HS-I2C2";
 			status = "okay";
+
+			adv_bridge: bridge at 39 {
+				status = "okay";
+
+				compatible = "adi,adv7533";
+				reg = <0x39>;
+
+				interrupt-parent = <&msmgpio>;
+				interrupts = <31 2>;
+
+				adi,dsi-lanes = <4>;
+
+				pd-gpios = <&msmgpio 32 0>;
+
+				avdd-supply = <&pm8916_l6>;
+				v1p2-supply = <&pm8916_l6>;
+				v3p3-supply = <&pm8916_l17>;
+
+				pinctrl-names = "default","sleep";
+				pinctrl-0 = <&adv7533_int_active &adv7533_switch_active>;
+				pinctrl-1 = <&adv7533_int_suspend &adv7533_switch_suspend>;
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port at 0 {
+						reg = <0>;
+						adv7533_in: endpoint {
+							remote-endpoint = <&dsi0_out>;
+						};
+					};
+
+					port at 1 {
+						reg = <1>;
+						adv7533_out: endpoint {
+							remote-endpoint = <&hdmi_con>;
+						};
+					};
+				};
+			};
 		};
 
 		i2c at 78ba000 {
@@ -164,6 +205,36 @@
 		lpass at 07708000 {
 			status = "okay";
 		};
+
+		mdss at 1a00000 {
+			status = "okay";
+
+			mdp at 1a01000 {
+				status = "okay";
+			};
+
+			dsi at 1a98000 {
+				status = "okay";
+
+				vdda-supply = <&pm8916_l2>;
+				vddio-supply = <&pm8916_l6>;
+
+				ports {
+					port at 1 {
+						endpoint {
+							remote-endpoint = <&adv7533_in>;
+							data-lanes = <0 1 2 3>;
+						};
+					};
+				};
+			};
+
+			dsi-phy at 1a98300 {
+				status = "okay";
+
+				vddio-supply = <&pm8916_l6>;
+			};
+		};
 	};
 
 	usb2513 {
@@ -178,6 +249,17 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&usb_id_default>;
 	};
+
+	hdmi-out {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con: endpoint {
+				remote-endpoint = <&adv7533_out>;
+			};
+		};
+	};
 };
 
 &smd_rpm_regulators {
-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
hosted by The Linux Foundation