[PATCH 3/3] drm/exynos/decon5433: fix trigger configuration

[Andrzej Hajda]

Hi Inki,


On 05/10/2016 07:31 AM, Inki Dae wrote:
> Hi Andrzej,
>
> 2016년 04월 29일 22:42에 Andrzej Hajda 이(가) 쓴 글:
>> It seems trigger cannot be configured too early, otherwise it does not work in
>> case of panel. The patch fixes also trigger flag logic, previously HW-TRIGGER
>> flag was cleared in case of panel - as a result panel used always software
> Andrzej, sorry but I can't understand what above two lines mean. Can you give me more details?

Details below.

>
>> trigger.
>>
>> Signed-off-by: Andrzej Hajda <a.hajda at samsung.com>
>> ---
>>  drivers/gpu/drm/exynos/exynos5433_drm_decon.c | 10 ++++------
>>  1 file changed, 4 insertions(+), 6 deletions(-)
>>
>> diff --git a/drivers/gpu/drm/exynos/exynos5433_drm_decon.c b/drivers/gpu/drm/exynos/exynos5433_drm_decon.c
>> index 7b4f699..9ae913b 100644
>> --- a/drivers/gpu/drm/exynos/exynos5433_drm_decon.c
>> +++ b/drivers/gpu/drm/exynos/exynos5433_drm_decon.c
>> @@ -151,11 +151,13 @@ static void decon_commit(struct exynos_drm_crtc *crtc)
>>  	val = CMU_CLKGAGE_MODE_SFR_F | CMU_CLKGAGE_MODE_MEM_F;
>>  	writel(val, ctx->addr + DECON_CMU);
>>  
>> +	if (ctx->out_type & (IFTYPE_I80 | I80_HW_TRG))
>> +		decon_setup_trigger(ctx);
> Shouldn't it be configured in case of using SW trigger mode also?
>
> Thanks,
> Inki Dae
>
>> +
>>  	/* lcd on and use command if */
>>  	val = VIDOUT_LCD_ON;
>>  	if (ctx->out_type & IFTYPE_I80) {
>>  		val |= VIDOUT_COMMAND_IF;
>> -		decon_setup_trigger(ctx);
>>  	} else {
>>  		val |= VIDOUT_RGB_IF;
>>  	}
>> @@ -380,9 +382,6 @@ static void decon_swreset(struct decon_context *ctx)
>>  	writel(VIDCON1_VCLK_RUN_VDEN_DISABLE, ctx->addr + DECON_VIDCON1);
>>  	writel(CRCCTRL_CRCEN | CRCCTRL_CRCSTART_F | CRCCTRL_CRCCLKEN,
>>  	       ctx->addr + DECON_CRCCTRL);
>> -
>> -	if (ctx->out_type & IFTYPE_I80)
>> -		decon_setup_trigger(ctx);
>>  }
>>  
>>  static void decon_enable(struct exynos_drm_crtc *crtc)
>> @@ -652,9 +651,8 @@ static int exynos5433_decon_probe(struct platform_device *pdev)
>>  
>>  	if (ctx->out_type & IFTYPE_HDMI) {
>>  		ctx->first_win = 1;
>> -		ctx->out_type = IFTYPE_I80;
>>  	} else if (of_get_child_by_name(dev->of_node, "i80-if-timings")) {
>> -		ctx->out_type = IFTYPE_I80;
>> +		ctx->out_type |= IFTYPE_I80;

ctx->out_type was overwritten here with IFTYPE_I80. So when
decon_setup_trigger
were called I80_HW_TRG bit was always clear and DECON_TRIGCON was configured
to use soft trigger.

Regards
Andrzej

>>  	}
>>  
>>  	for (i = 0; i < ARRAY_SIZE(decon_clks_name); i++) {
>>