[PATCH 3/3] drm/exynos/decon5433: fix trigger configuration

[Inki Dae]

Hi Andrzej,

2016년 05월 10일 15:08에 Andrzej Hajda 이(가) 쓴 글:
> Hi Inki,
> 
> 
> On 05/10/2016 07:31 AM, Inki Dae wrote:
>> Hi Andrzej,
>>
>> 2016년 04월 29일 22:42에 Andrzej Hajda 이(가) 쓴 글:
>>> It seems trigger cannot be configured too early, otherwise it does not work in
>>> case of panel. The patch fixes also trigger flag logic, previously HW-TRIGGER
>>> flag was cleared in case of panel - as a result panel used always software
>> Andrzej, sorry but I can't understand what above two lines mean. Can you give me more details?
> 
> Details below.
> 
>>
>>> trigger.
>>>
>>> Signed-off-by: Andrzej Hajda <a.hajda at samsung.com>
>>> ---
>>>  drivers/gpu/drm/exynos/exynos5433_drm_decon.c | 10 ++++------
>>>  1 file changed, 4 insertions(+), 6 deletions(-)
>>>
>>> diff --git a/drivers/gpu/drm/exynos/exynos5433_drm_decon.c b/drivers/gpu/drm/exynos/exynos5433_drm_decon.c
>>> index 7b4f699..9ae913b 100644
>>> --- a/drivers/gpu/drm/exynos/exynos5433_drm_decon.c
>>> +++ b/drivers/gpu/drm/exynos/exynos5433_drm_decon.c
>>> @@ -151,11 +151,13 @@ static void decon_commit(struct exynos_drm_crtc *crtc)
>>>  	val = CMU_CLKGAGE_MODE_SFR_F | CMU_CLKGAGE_MODE_MEM_F;
>>>  	writel(val, ctx->addr + DECON_CMU);
>>>  
>>> +	if (ctx->out_type & (IFTYPE_I80 | I80_HW_TRG))
>>> +		decon_setup_trigger(ctx);
>> Shouldn't it be configured in case of using SW trigger mode also?
>>
>> Thanks,
>> Inki Dae
>>
>>> +
>>>  	/* lcd on and use command if */
>>>  	val = VIDOUT_LCD_ON;
>>>  	if (ctx->out_type & IFTYPE_I80) {
>>>  		val |= VIDOUT_COMMAND_IF;
>>> -		decon_setup_trigger(ctx);
>>>  	} else {
>>>  		val |= VIDOUT_RGB_IF;
>>>  	}
>>> @@ -380,9 +382,6 @@ static void decon_swreset(struct decon_context *ctx)
>>>  	writel(VIDCON1_VCLK_RUN_VDEN_DISABLE, ctx->addr + DECON_VIDCON1);
>>>  	writel(CRCCTRL_CRCEN | CRCCTRL_CRCSTART_F | CRCCTRL_CRCCLKEN,
>>>  	       ctx->addr + DECON_CRCCTRL);
>>> -
>>> -	if (ctx->out_type & IFTYPE_I80)
>>> -		decon_setup_trigger(ctx);
>>>  }
>>>  
>>>  static void decon_enable(struct exynos_drm_crtc *crtc)
>>> @@ -652,9 +651,8 @@ static int exynos5433_decon_probe(struct platform_device *pdev)
>>>  
>>>  	if (ctx->out_type & IFTYPE_HDMI) {
>>>  		ctx->first_win = 1;
>>> -		ctx->out_type = IFTYPE_I80;
>>>  	} else if (of_get_child_by_name(dev->of_node, "i80-if-timings")) {
>>> -		ctx->out_type = IFTYPE_I80;
>>> +		ctx->out_type |= IFTYPE_I80;
> 
> ctx->out_type was overwritten here with IFTYPE_I80. So when
> decon_setup_trigger
> were called I80_HW_TRG bit was always clear and DECON_TRIGCON was configured
> to use soft trigger.

Indeed. Then shouldn't decon_setup_trigger function be called in both cases - SW and HW trigger modes?
Is there any reason to call the function only in case of HW trigger mode?

Thanks,
Inki Dae

> 
> Regards
> Andrzej
> 
>>>  	}
>>>  
>>>  	for (i = 0; i < ARRAY_SIZE(decon_clks_name); i++) {
>>>
> 
>