[PATCH 3/3] drm/exynos/decon5433: fix trigger configuration

[Andrzej Hajda]

On 05/10/2016 08:24 AM, Inki Dae wrote:
> Hi Andrzej,
>
> 2016년 05월 10일 15:08에 Andrzej Hajda 이(가) 쓴 글:
>> Hi Inki,
>>
>>
>> On 05/10/2016 07:31 AM, Inki Dae wrote:
>>> Hi Andrzej,
>>>
>>> 2016년 04월 29일 22:42에 Andrzej Hajda 이(가) 쓴 글:
>>>> It seems trigger cannot be configured too early, otherwise it does not work in
>>>> case of panel. The patch fixes also trigger flag logic, previously HW-TRIGGER
>>>> flag was cleared in case of panel - as a result panel used always software
>>> Andrzej, sorry but I can't understand what above two lines mean. Can you give me more details?
>> Details below.
>>
>>>> trigger.
>>>>
>>>> Signed-off-by: Andrzej Hajda <a.hajda at samsung.com>
>>>> ---
>>>>  drivers/gpu/drm/exynos/exynos5433_drm_decon.c | 10 ++++------
>>>>  1 file changed, 4 insertions(+), 6 deletions(-)
>>>>
>>>> diff --git a/drivers/gpu/drm/exynos/exynos5433_drm_decon.c b/drivers/gpu/drm/exynos/exynos5433_drm_decon.c
>>>> index 7b4f699..9ae913b 100644
>>>> --- a/drivers/gpu/drm/exynos/exynos5433_drm_decon.c
>>>> +++ b/drivers/gpu/drm/exynos/exynos5433_drm_decon.c
>>>> @@ -151,11 +151,13 @@ static void decon_commit(struct exynos_drm_crtc *crtc)
>>>>  	val = CMU_CLKGAGE_MODE_SFR_F | CMU_CLKGAGE_MODE_MEM_F;
>>>>  	writel(val, ctx->addr + DECON_CMU);
>>>>  
>>>> +	if (ctx->out_type & (IFTYPE_I80 | I80_HW_TRG))
>>>> +		decon_setup_trigger(ctx);
>>> Shouldn't it be configured in case of using SW trigger mode also?
>>>
>>> Thanks,
>>> Inki Dae
>>>
>>>> +
>>>>  	/* lcd on and use command if */
>>>>  	val = VIDOUT_LCD_ON;
>>>>  	if (ctx->out_type & IFTYPE_I80) {
>>>>  		val |= VIDOUT_COMMAND_IF;
>>>> -		decon_setup_trigger(ctx);
>>>>  	} else {
>>>>  		val |= VIDOUT_RGB_IF;
>>>>  	}
>>>> @@ -380,9 +382,6 @@ static void decon_swreset(struct decon_context *ctx)
>>>>  	writel(VIDCON1_VCLK_RUN_VDEN_DISABLE, ctx->addr + DECON_VIDCON1);
>>>>  	writel(CRCCTRL_CRCEN | CRCCTRL_CRCSTART_F | CRCCTRL_CRCCLKEN,
>>>>  	       ctx->addr + DECON_CRCCTRL);
>>>> -
>>>> -	if (ctx->out_type & IFTYPE_I80)
>>>> -		decon_setup_trigger(ctx);
>>>>  }
>>>>  
>>>>  static void decon_enable(struct exynos_drm_crtc *crtc)
>>>> @@ -652,9 +651,8 @@ static int exynos5433_decon_probe(struct platform_device *pdev)
>>>>  
>>>>  	if (ctx->out_type & IFTYPE_HDMI) {
>>>>  		ctx->first_win = 1;
>>>> -		ctx->out_type = IFTYPE_I80;
>>>>  	} else if (of_get_child_by_name(dev->of_node, "i80-if-timings")) {
>>>> -		ctx->out_type = IFTYPE_I80;
>>>> +		ctx->out_type |= IFTYPE_I80;
>> ctx->out_type was overwritten here with IFTYPE_I80. So when
>> decon_setup_trigger
>> were called I80_HW_TRG bit was always clear and DECON_TRIGCON was configured
>> to use soft trigger.
> Indeed. Then shouldn't decon_setup_trigger function be called in both cases - SW and HW trigger modes?
> Is there any reason to call the function only in case of HW trigger mode?

With this patch function is called under following condition:
> +	if (ctx->out_type & (IFTYPE_I80 | I80_HW_TRG))
> +		decon_setup_trigger(ctx);

So it is called always in case of I80 mode, in such case value of I80_HW_TRG
determines if it should use sw or hw trigger.

Regards
Andrzej


>
> Thanks,
> Inki Dae
>
>> Regards
>> Andrzej
>>
>>>>  	}
>>>>  
>>>>  	for (i = 0; i < ARRAY_SIZE(decon_clks_name); i++) {
>>>>
>>