[PATCH v9 2/4] dt-bindings: drm/bridge: Document sn65dsi86 bridge bindings

Rob Herring robh at kernel.org
Wed Jun 13 15:03:53 UTC 2018


On Wed, Jun 13, 2018 at 5:08 AM, Sandeep Panda <spanda at codeaurora.org> wrote:
> Document the bindings used for the sn65dsi86 DSI to eDP bridge.
>
> Changes in v1:
>  - Rephrase the dt-binding descriptions to be more inline with existing
>    bindings (Andrzej Hajda).
>  - Add missing dt-binding that are parsed by corresponding driver
>    (Andrzej Hajda).
>
> Changes in v2:
>  - Remove edp panel specific dt-binding entries. Only keep bridge
>    specific entries (Sean Paul).
>  - Remove custom-modes dt entry since its usage is removed from driver also (Sean Paul).
>  - Remove is-pluggable dt entry since this will not be needed anymore (Sean Paul).
>
> Changes in v3:
>  - Remove irq-gpio dt entry and instead populate is an interrupt
>    property (Rob Herring).
>
> Changes in v4:
>  - Add link to bridge chip datasheet (Stephen Boyd)
>  - Add vpll and vcc regulator supply bindings (Stephen Boyd)
>  - Add ref clk optional dt binding (Stephen Boyd)
>  - Add gpio-controller optional dt binding (Stephen Boyd)
>
> Changes in v5:
>  - Use clock property to specify the input refclk (Stephen Boyd).
>  - Update gpio cell and pwm cell numbers (Stephen Boyd).
>
> Changes in v6:
>  - Add property to mention the lane mapping scheme and polarity inversion
>    (Stephen Boyd).
>
> Changes in v7:
>  - Detail description of lane mapping scheme dt property (Andrzej
>    Hajda/ Rob Herring).
>  - Removed HDP gpio binding, since the bridge uses IRQ signal to
>    determine HPD, and IRQ property is already documented in binding.
>
> Changes in v8:
>  - Removed unnecessary explanation of lane mapping and polarity dt
>    property, since these are already explained in media/video-interface
>    dt binidng (Rob Herring).
>
> Signed-off-by: Sandeep Panda <spanda at codeaurora.org>
> ---
>  .../bindings/display/bridge/ti,sn65dsi86.txt       | 90 ++++++++++++++++++++++
>  1 file changed, 90 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt
>
> diff --git a/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt b/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt
> new file mode 100644
> index 0000000..601454c
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt
> @@ -0,0 +1,90 @@
> +SN65DSI86 DSI to eDP bridge chip
> +--------------------------------
> +
> +This is the binding for Texas Instruments SN65DSI86 bridge.
> +http://www.ti.com/general/docs/lit/getliterature.tsp?genericPartNumber=sn65dsi86&fileType=pdf
> +
> +Required properties:
> +- compatible: Must be "ti,sn65dsi86"
> +- reg: i2c address of the chip, 0x2d as per datasheet
> +- enable-gpios: OF device-tree gpio specification for bridge_en pin (active high)
> +
> +- vccio-supply: A 1.8V supply that powers up the digital IOs.
> +- vpll-supply: A 1.8V supply that powers up the displayport PLL.
> +- vcca-supply: A 1.2V supply that powers up the analog circuits.
> +- vcc-supply: A 1.2V supply that powers up the digital core.
> +
> +Optional properties:
> +- interrupts: Specifier for the SN65DSI86 interrupt line.
> +
> +- ddc-i2c-bus: phandle of the I2C controller used for DDC EDID probing
> +
> +- gpio-controller: Marks the device has a GPIO controller.
> +- #gpio-cells    : Should be two. The first cell is the pin number and
> +                   the second cell is used to specify flags.
> +                   See ../../gpio/gpio.txt for more information.
> +- #pwm-cells : Should be one. See ../../pwm/pwm.txt for description of
> +               the cell formats.
> +
> +- clock-names: should be "refclk"
> +- clocks: Specification for input reference clock. The reference
> +         clock rate must be 12 MHz, 19.2 MHz, 26 MHz, 27 MHz or 38.4 MHz.
> +
> +- data-lanes: Specification to describe the logical to physical lane
> +             mapping scheme. See ../../media/video-interface.txt for more
> +             information.
> +- lane-polarities: Specification to describe the polarity of physical lanes.
> +                  See ../../media/video-interface.txt for more information.

You are still defining the properties here. All you need is:

data-lanes: See ../../media/video-interface.txt

Perhaps you need to say should be 4 lanes, but OTOH everything tends
to be 4 lanes.

Rob


More information about the dri-devel mailing list