[PATCH RFC 5/8] dt-bindings: display: add Unisoc's mipi dsi&dphy bindings

[Kevin Tang]

From: Kevin Tang <kevin.tang at unisoc.com>

Adds MIPI DSI Master and MIPI DSI-PHY (D-PHY)
support for Unisoc's display subsystem.

Cc: Orson Zhai <orsonzhai at gmail.com>
Cc: Baolin Wang <baolin.wang at linaro.org>
Cc: Chunyan Zhang <zhang.lyra at gmail.com>
Signed-off-by: Kevin Tang <kevin.tang at unisoc.com>
---
 .../devicetree/bindings/display/sprd/dphy.txt      | 49 ++++++++++++++++
 .../devicetree/bindings/display/sprd/dsi.txt       | 68 ++++++++++++++++++++++
 2 files changed, 117 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/display/sprd/dphy.txt
 create mode 100644 Documentation/devicetree/bindings/display/sprd/dsi.txt

diff --git a/Documentation/devicetree/bindings/display/sprd/dphy.txt b/Documentation/devicetree/bindings/display/sprd/dphy.txt
new file mode 100644
index 0000000..474c2b2
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/sprd/dphy.txt
@@ -0,0 +1,49 @@
+Unisoc MIPI DSI-PHY (D-PHY)
+============================================================================
+
+Required properties:
+  - compatible: value should be "sprd,dsi-phy".
+  - reg: must be the dsi controller base address.
+  - #address-cells, #size-cells: should be set respectively to <1> and <0>
+
+Video interfaces:
+  Device node can contain video interface port nodes according to [1].
+  The following are properties specific to those nodes:
+
+  port node inbound:
+    - reg: (required) must be 0.
+  port node outbound:
+    - reg: (required) must be 1.
+
+  endpoint node connected from DSI controller node (reg = 0):
+    - remote-endpoint: specifies the endpoint in DSI node.
+  endpoint node connected to panel node (reg = 1):
+    - remote-endpoint: specifies the endpoint in panel node.
+
+[1]: Documentation/devicetree/bindings/media/video-interfaces.txt
+
+
+Example:
+
+	dphy: dphy {
+		compatible = "sprd,dsi-phy";
+		reg = <0x0 0x63100000 0x0 0x1000>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* input port*/
+		port at 1 {
+			reg = <1>;
+			dphy_in: endpoint {
+				remote-endpoint = <&dsi_out>;
+			};
+		};
+
+		/* output port */
+		port at 0 {
+			reg = <0>;
+			dphy_out: endpoint {
+				remote-endpoint = <&panel_in>;
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/display/sprd/dsi.txt b/Documentation/devicetree/bindings/display/sprd/dsi.txt
new file mode 100644
index 0000000..1719ff5
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/sprd/dsi.txt
@@ -0,0 +1,68 @@
+Unisoc MIPI DSI Master
+=============================================================================
+
+Required properties:
+  - compatible: value should be "sprd,dsi-host";
+  - reg: physical base address and length of the registers set for the device
+  - interrupts: should contain DSI interrupt
+  - clocks: list of clock specifiers, must contain an entry for each required
+	    entry in clock-names
+  - clock-names: list of clock names sorted in the same order as the clocks
+                 property.
+  - #address-cells, #size-cells: should be set respectively to <1> and <0>
+    according to DSI host bindings (see MIPI DSI bindings [1])
+
+Optional properties:
+  - power-domains: a phandle to DSIM power domain node
+
+Child nodes:
+  Should contain DSI peripheral nodes (see MIPI DSI bindings [1]).
+
+Video interfaces:
+  Device node can contain video interface port nodes according to [2].
+  The following are properties specific to those nodes:
+
+  port node inbound:
+    - reg: (required) must be 0.
+  port node outbound:
+    - reg: (required) must be 1.
+
+  endpoint node connected from DPU node (reg = 0):
+    - remote-endpoint: specifies the endpoint in DPU node.
+  endpoint node connected to D-PHY node (reg = 1):
+    - remote-endpoint: specifies the endpoint in D-PHY node.
+
+[1]: Documentation/devicetree/bindings/display/mipi-dsi-bus.txt
+[2]: Documentation/devicetree/bindings/media/video-interfaces.txt
+
+Example:
+
+SoC specific DT entry:
+
+	dsi: dsi at 63100000 {
+		compatible = "sprd,dsi-host";
+		reg = <0 0x63100000 0 0x1000>;
+		interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
+		clock-names = "clk_aon_apb_disp_eb";
+		clocks = <&clk_aon_top_gates 2>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port at 0 {
+				reg = <0>;
+				dsi_in: endpoint {
+					remote-endpoint = <&dpu_out>;
+				};
+			};
+
+			port at 1 {
+				reg = <1>;
+				dsi_out: endpoint at 1 {
+					remote-endpoint = <&dphy_in>;
+				};
+			};
+		};
+	};
\ No newline at end of file
-- 
2.7.4